The product page for 【Suntool】 has been newly added with the case study "Hot Melt Adhesion of Masking Tape"!

This is a case study introducing solutions for manufacturers of paper products and packaging materials. The introduction of the E-Coater coating system has achieved a reduction in manufacturing costs.

[Consultation from a manufacturer of paper products and packaging materials] We were contacted by a manufacturer who is currently applying water-based solvent adhesives to washi paper to produce masking tape. They wish to switch to hot melt adhesive application equipment to reduce material costs. [Introduced System] E Coater Head (coating width 310mm) Coating amount: 20g/m2 VH60WSS tank [Features] - Uniform coating is possible - Special coater head for on-roll coating - Maximum coating width: 600mm - Ideal for laminating thin films as it does not create lines or unevenness on the surface of the sheet after laminating printed sheets (films) [Implementation Effects] Achieved increased production speed and reduced manufacturing costs. *For more details, please download the PDF or feel free to contact us.

• Other mounting machines
• Painting Machine
• Other painting machines

There are methods for applying with tension between rolls and on-roll application, allowing for continuous/intermittent (partial application) depending on the purpose!

This is a method for applying hot melt adhesive in a uniform width, over a surface, or in stripes. There are methods for applying it under tension between rolls and on-roll application, which can be continuous or intermittent (partial application) depending on the purpose. 【Features】 ■ Coater head for contact-type application ■ The application pattern can be arbitrarily set according to the shim pattern. ■ High-speed intermittent adhesion is possible, accommodating adhesives from high viscosity to low viscosity. ■ Beautiful coating with thin film adhesion. ■ There are measures to prevent winding during application and to address clumping of hot melt adhesives (using hot air). * For more details, please download the PDF or feel free to contact us.

• Painting Machine
• spray
• Other painting machines

● What is a packaging container air leak test device? It is a leak testing device that identifies the peeling, tearing, and presence of pinholes in packaging containers for pharmaceuticals and other products, conducting a Container Closure Integrity Test (CCIT). It can be applied to a wide variety of packaging containers, including flexible packaging, bottle containers, and glass containers, primarily in pharmaceutical packaging. The measurement method employs the <sealed chamber method (pressure change leak testing method 1)>. A sample is placed in the chamber, and by applying pressure or vacuum and measuring the pressure change within the chamber, quantitative inspection is performed. It can be used in various scenarios, including offline manufacturing, inline manufacturing, CMC laboratories, quality control laboratories, and stability testing. * The containers subject to inspection are referred to as "work" or "samples." Here, specific samples are referred to as "samples" to differentiate the terminology.

The pinhole inspection for packaging engineering is fully automated, eliminating packaging defects based on certain quality standards. The judgment results and operational status can be managed via a monitor screen. - Quantitative management of quality standards for the pinhole inspection process - Ensuring the quality of the product's shelf life - Establishing evaluation criteria for the manufacturing process, achieving quantitative quality assurance - Slim and space-saving design that can be connected to existing production lines - Quick changeover for product variety switching can be handled in a short time by exchanging chambers - Fully domestically produced, allowing for rapid maintenance and troubleshooting - Example target works: pillow packaging, packaged rice (packaged cooked rice), etc. *Please consult us regarding the use of this product for pharmaceuticals.

Hotron Inc. has launched its new product, the "Vehicle Count Sensor CCS3"! This product is a ceiling-mounted sensor that combines infrared and radar technology. It reliably detects vehicles in both directions with a single unit, accommodating traffic during congestion and vehicle passing, thus achieving efficient occupancy management in large parking lots. Additionally, it can be utilized for exit warning purposes in addition to vehicle counting, contributing to the safe and smooth operation of parking facilities. 'Features' - Improved detection performance against changes in road surface during rainy weather by using both infrared and radar. - Equipped with IP67 waterproof and dustproof performance, making it effective even in salt damage areas. - Various settings can be configured from a dedicated app (for Android devices), with current settings easily understandable at a glance. - The base dimensions are the same as the previous model "CCS2," allowing for smooth replacement of existing equipment. *For more details, please refer to the product information, catalog download, or contact us.*

In civil engineering projects conducted in mountainous areas, there are construction conditions that differ from flat land, such as narrow access roads and limited working space. The "Hyper CLT Mats," made from CLT (Cross Laminated Timber), excel in these situations. The 5×10 mats weigh approximately 230 kg, making them relatively lightweight and easy to install, remove, and relocate even with small machinery, depending on the site conditions. They can be utilized in various locations in mountainous areas, such as unpaved access roads, temporary roads, material storage areas, and heavy machinery workspaces. Additionally, they offer environmental benefits such as harmony with the natural landscape, reduction of metal noise and summer glare, and CO2 sequestration. The Hyper CLT Mats are registered under the Ministry of Land, Infrastructure, Transport and Tourism's NETIS technology "TH-250021-A." As a wooden lightweight mat combining wood, NETIS, civil engineering, and CLT, it is a new option that is easy to use even in the challenging construction conditions of mountainous sites.

Introducing a "non-destructive testing device as an alternative to the submerged test" for pharmaceutical packaging products. "Complete vial leak testing device | MSQ-2002 series" Fully automating leak tests for various vials, bottles, eye drops, and cylindrical containers. Please check the link below for videos and catalogs.