Lightweight even though it's made of steel! Lightweight steel sliding door.

Sleek and lightweight steel sliding door.

The door interior is a lightweight steel sliding door that uses an aluminum frame with honeycomb material and foam-type insulation. It can be used for a wide range of applications, from human traffic to the entry of large machinery. The interior consists of a lightweight steel sliding door made of an aluminum frame, honeycomb material, and styrene foam, with surface materials made of thin steel plates ranging from 0.4mm to 0.8mm, allowing for easier opening and closing compared to standard steel sliding doors. There are three types of opening and closing mechanisms available: manual, self-closing, and automatic. The rail cover can also be optionally equipped with a sanitary cover (sloped cover). The guide block is stored inside, and a rubber seal is used to enhance airtightness at the opening. In addition to being shipped with rust-proof paint, it can also be shipped with baked-on paint in specified colors. It is possible to change the viewing window and edge materials to stainless steel, making it a highly customizable lightweight steel sliding door. *1 Two locations (one set) at the door head and door tail. * This door does not qualify as a specific fire protection facility or fire protection equipment. Customers considering its use as fire protection equipment according to structural regulations should contact our sales representative. * A 1.6mm thick steel edge material surrounds the door body.

• others

Lightweight and smart stainless steel sliding door

This is a stainless steel sliding door with excellent weather resistance. Except for some visible parts, it is made entirely of stainless steel, making it suitable for rooms where aluminum or steel cannot be used due to chemical resistance and other factors. The surface material of the door itself is made of stainless steel sheet as thin as 0.5mm, and the interior consists of an aluminum frame and either paper honeycomb or styrene foam, allowing for very lightweight opening and closing compared to typical stainless steel doors. It is available in three types: manual, self-closing, and automatic, and the stainless steel rail cover can optionally accommodate a sanitary cover (sloped cover). The guide block is stored inside, and the opening is sealed with a rubber flap to enhance airtightness. *The surface material can also be color-coated steel or aluminum in addition to stainless steel sheet. It can accommodate different surface materials on either side, such as one side being stainless steel and the other side being color-coated steel. *There are two guide blocks (one set) at the leading and trailing edges.

• stainless
• Other clean room equipment and facilities
• others

Individually certified fire protection equipment 'Legacy Shield' series! Individually certified product with transparent glass, 60-minute fire-resistant specific fire sliding door.

This is a steel self-closing sliding door that has been certified by the Minister of Land, Infrastructure, Transport and Tourism as a specific fire prevention device (fire door). It features transparent glass without mesh, ensuring a clear view even in fire compartments. Since it is a type that attaches the rail directly to the wall, it can also be installed later. Additionally, it has a three-sided frame without a bottom frame, allowing for a smooth passage for carts and other items without any steps. *For more details, please refer to the PDF materials or feel free to contact us.*

• others

Supports lightweight partitions! Utility ultra-lightweight steel sliding door.

This is a versatile sliding door that accommodates lightweight partitions and RC structures, suitable for a wide range of applications from standard door sizes to large sizes for the entry and exit of heavy machinery. It is an ultra-lightweight steel sliding door that can be used for various purposes, from pedestrian access to large doors for heavy machinery. The frame of the opening can be selected from aluminum, steel, or stainless steel, all of which feature a rubber seal that closes the gap between the door and the frame. The opening and closing methods include manual, self-closing, and automatic options. Additionally, it is possible to have the rail cover as a sanitary cover (sloped cover) as an option. The guide blocks are stored inside the door at two locations, at the leading and trailing edges, per set.

• Other clean room equipment and facilities

Automatic sliding door with automatic closure during emergencies and fire protection equipment compatibility.

Automatically closes even in emergencies with automatic opening and closing! This is an automatic sliding door that complies with fire protection equipment and specific fire protection equipment regulations. It automatically closes upon receiving signals from fire alarms or smoke detectors, and as a standard feature, it is equipped with an emergency battery, allowing it to close automatically even if power is cut off during a fire. The automatic door engine is compatible with products from Fuso Electric Industry and Hashida Giken. *1 We believe that it meets the requirements for specific fire protection equipment, but interpretations may vary depending on the inspecting administrative agency, so please be sure to check with the relevant administrative agency in your installation area in advance. *2 It can also be configured without a battery.

• others

Fire-resistant equipment compatible! Directly mounted rail type self-closing steel sliding door.

A direct-attach steel sliding door that can be added to fireproof insulated panels! This is a type of steel sliding door that is directly attached to the wall with rails. It is designed with the installation on fireproof insulated panels in mind*1, and can be used as fire protection equipment (with or without a 6.8mm wire glass window) or as specific fire protection equipment (only without a window)*2. It supports both single and double sliding configurations. *1 It can also be adapted for walls other than fireproof insulated panels. Please contact us for details. *2 While we believe it meets the requirements for fire protection equipment and specific fire protection equipment, interpretations may vary depending on the inspecting administrative agency, so please be sure to confirm with the relevant administrative agency in your installation area beforehand.

• others

Fire-resistant equipment compatible! Lightweight partition wall storage type steel sliding door.

A built-in steel sliding door that fits neatly within the wall! This is a type of sliding door that is stored within a lightweight partition wall. Since the overhead rail is also built into the wall, it is designed to minimize dust accumulation on the top of the rail, making it easy to clean. It comes standard with a sliding closer without a rail stop, and the surface material is made of 1.6mm steel plate. It can be used with a window as a fire protection device, or without a window as a specific fire protection device. *1 The compatible thickness for the lightweight partition wall is only 115mm. *2 Only 6.8mm wired glass is available. *3 This product meets the requirements of relevant laws and regulations for specific fire protection devices and fire protection devices; however, interpretations of the law may vary depending on the administrative agency conducting the inspection. It is recommended to confirm the legal compliance of this product with the administrative agency in the area where it will be installed.

• others

High airtightness and thermal insulation doors and windows available! Custom sizes can be ordered in 1mm increments.

Our company offers a wide range of specialized fixtures such as "doors" and "windows" that have higher functionality than those for general buildings, used in factories, clean rooms, and various testing laboratories! 【Example of fixtures featured in the catalog】 ◎ Ideal for low-temperature clean rooms: "Insulated Resin Flush Door" ◎ Lightweight with a smart appearance: "Aluminum Frame Sliding Door" ◎ Suitable for large machinery loading and unloading: "Removable Machine Hatch" ◎ Fusion of sliding and flush doors: "Sliding Plus Door" ◎ No glass work required! Easy installation: "Aluminum FIX Window" Most products can be custom-made to the millimeter! ★ Currently, we are offering a 'Comprehensive Catalog' that covers all products ★ You can view an excerpt version from "Download." If you would like the complete version, please request it from "Contact Us."

• Clean Booth
• Other clean room equipment and facilities
• Office furniture

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repair without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or variations in dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding methods for repairs can change the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Waterworks Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repairs without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

Fukuda Corporation has been pursuing leak detection for 60 years and is dedicated to advancing the future of leak testing. 【 Supporting Various Leak Tests: Air Leak Test / Gas Leak Test (Hydrogen Gas, Helium Gas) 】 We develop, manufacture, and sell leak testing equipment to inspect airtightness and sealing performance. We will propose suitable testers and devices for each inspection target. 【 Target Industries and Examples of Inspection Targets 】 - Automotive Industry: Engines, FC components, valves and piping, various parts - Electronic Components Industry: Smartphones, keyless switches, various small sensors - Pharmaceuticals / Food / Cosmetics Industry: Bottle containers, syringes, vials, eye drop containers, pillow packaging, PTP packaging We will propose the most suitable leak testers for each industry. 【 ISO Certification 】JIS Q 9001:2015 (ISO 9001:2015)

This is a collection of links to Fukuda's technical columns. It covers various topics related to leak tests and more... Please check the related links for more information.