Analysis of mica sheet adhesive components using GC/MS.

It is possible to investigate components that cannot be identified by spectroscopy alone, as well as trace additives that cannot be detected!

This is an introduction to the analysis of the components of mica sheet adhesives using GC/MS. To investigate what components are contained in the mica sheet, spectroscopic measurements were conducted, suggesting that silicone-based adhesives are used. To examine the composition of the silicone-based adhesive, GC/MS measurements were performed. It was found that pentacyclooctasiloxane is used, and it was also discovered that dibutyl phthalate is added as a plasticizer and chain-saturated hydrocarbons such as tridecane are added as lubricants. 【Components of the mica sheet】 ■ Pentacyclooctasiloxane (cage-like polymethylsilsesquioxane) ■ Dibutyl phthalate ■ Chain-saturated hydrocarbons such as tridecane *For more details, please refer to the PDF document or feel free to contact us.

• Analytical Equipment and Devices
• Spectroscopic Analysis Equipment

Comparison of components in liquid crystal panels using gas chromatography-mass spectrometry (GC-MS) is published!

This document introduces a comparison of components in PC monitors and digital clocks using gas chromatography-mass spectrometry (GC-MS). Liquid crystal displays contain small organic substances (liquid crystal molecules). These have evolved into molecular structures suitable for product characteristics due to technological innovations. Our company clarifies these differences at the molecular level using GC-MS, allowing us to confirm that the liquid crystal molecules are appropriate for their intended use and to check for the presence of impurities. [Contents] ■ Component comparison of PC monitors and digital clocks using GC-MS ■ Case studies of GC-MS analysis of liquid crystal components We compared the number of components and characteristics of segment-type liquid crystal displays (digital clocks) and color TFT liquid crystal displays (PC monitors). *For more details, please refer to the PDF document or feel free to contact us.

• Contract Analysis

Focusing on sandalwood (Byakudan), which is used as a raw material for incense! Here is an example of component analysis using GC-MS.

Due to the risk of depletion of natural ingredients, artificially synthesized alternative components may be used, and their identification is suitable for separation and analysis using methods such as GCMS. This time, we focused on sandalwood (Byakudan), which is used as a raw material for incense. We tested whether the components of sandalwood could be detected in two types of incense (A and B) with its fragrance. In incense A, santanol was detected, while in incense B, santanol was not detected, and another fragrant component was found. Among these, bugdanol is a type of synthetic fragrance, and due to its structural characteristics, it is believed to have a sandalwood-like scent. [Components of Incense A] ■ Bugdanol: Trace amounts ■ Cedrol: None ■ α-Santalol: Present ■ β-Santalol: Present *For more details, please refer to the PDF document or feel free to contact us.

• Analytical Equipment and Devices
• Contract Analysis

The aldol reaction progresses under the influence of temperature, humidity, and light! Example of impurity analysis in ethanol and acetone.

This is an example of analyzing impurities confirmed from a solvent when high-purity products are stored in inappropriate environments, using liquid injection GC-MS. Ethanol stored in a light-protective reagent bottle in a cool, dark place was transferred to a used plastic wash bottle and left at room temperature for about a month. As a result, impurities such as triethyl borate and alkylbenzenes were detected. Additionally, acetone stored in a light-protective reagent bottle in a cool, dark place was transferred to a transparent glass bottle without light protection and left at room temperature for about a month, resulting in the detection of diacetone alcohol as an impurity. [Impurity Analysis in Ethanol] ■ Ethanol stored in a light-protective reagent bottle in a cool, dark place was transferred to a used plastic wash bottle and left at room temperature for about a month (the opening of the wash bottle was not sealed). ■ Result: Impurities such as triethyl borate and alkylbenzenes were detected. *For more details, please refer to the PDF document or feel free to contact us.

• Analytical Equipment and Devices
• Contract Analysis
• Other contract services

Introducing the sample introduction device and the types of analytical samples and analysis content that each device specializes in!

GC-MS analysis is a method commonly used for the analysis of organic components and organic structure analysis. With auxiliary devices, it is capable of a wide range of analyses, from low molecular substances like solvents to high molecular substances like plastics. In this document, we will introduce the sample introduction devices owned by Aites, as well as the types of analysis samples and analysis content that each device specializes in. We invite you to read it. 【Contents】 ■ Overview ■ Conditions ■ Samples ■ Data Obtained ■ Analysis Examples *For more details, please refer to the PDF document or feel free to contact us.

• Analytical Equipment and Devices

It is possible to analyze with good sensitivity using thermal desorption GC-MS analysis! We propose methods tailored to the symptoms of issues and objectives.

Various additives are used in polymers to improve stability and processability; however, due to environmental impact and long-term storage, additive components may precipitate on the polymer surface, or the additives themselves may undergo chemical changes, leading to discoloration and degradation. This document presents examples of analyzing the bleed-out of additives and the chemical changes of additive components due to UV irradiation using thermal desorption GC-MS. Although additive components are present in only small amounts compared to the main polymer components, they can be analyzed sensitively using thermal desorption GC-MS. We propose methods tailored to specific issues or objectives, such as predicting product degradation in combination with reliability testing, thermal analysis, and main component analysis. Please feel free to contact us. [Contents] ■ Analysis of additive components bled out from nitrile rubber ■ Analysis of additive components in nylon 66 subjected to UV irradiation *For more details, please refer to the PDF document or feel free to contact us.

• Other analyses
• Contract Analysis
• Analysis Services

By adding a special reagent to the sample and heating it, it becomes possible to detect substances that are usually difficult to detect!

In a typical thermal decomposition GCMS, samples are heated to detect volatile components; however, analyzing components that do not volatilize upon heating or those with low detection sensitivity is challenging. Therefore, by adding a special reagent to the sample and heating it, it becomes possible to detect substances that are usually difficult to identify. For example, in the analysis of polymers, thermal decomposition of the polymer results in the detection of a large number of decomposition products, and in some cases, peaks may overlap with other additives, making analysis difficult. However, by performing reactive thermal decomposition GCMS, it is possible to detect the methyl esters of monomers and to separate and analyze them from the additives. Thus, even when the target analytes are difficult to detect using conventional analysis, reactive thermal decomposition GCMS allows for sensitive detection by selecting appropriate reagents for the analytes. [Examples] - Analysis of phthalate esters (DIDP) - Analysis of polymers (polyethylene terephthalate) - Analysis of copper corrosion inhibitors (BTA) *For more details, please refer to the PDF document or feel free to contact us.

• Contract Analysis
• Analysis Services

We have added a new **"Glossary"** to the Hyper CLT sheet website. In the civil engineering and construction industries, there are many specialized terms such as "CLT," "NETIS," "temporary roads," and "wooden lightweight sheets." Therefore, we have introduced related terms in an easy-to-understand manner so that those who are encountering Hyper CLT sheets for the first time can understand the products and technologies. Hyper CLT sheets are wooden lightweight sheets for civil engineering that utilize wood CLT and are registered under the Ministry of Land, Infrastructure, Transport and Tourism's NETIS technology as **"TH-250021-A."** We hope that by not only conveying the features of the product but also sharing the underlying technologies and terminology, users will feel a closer connection to Hyper CLT sheets. We will continue to enhance our website and provide clear information related to wood, NETIS, civil engineering, and CLT.

Hotron Inc. has launched its new product, the "Vehicle Count Sensor CCS3"! This product is a ceiling-mounted sensor that combines infrared and radar technology. It reliably detects vehicles in both directions with a single unit, accommodating traffic during congestion and vehicle passing, thus achieving efficient occupancy management in large parking lots. Additionally, it can be utilized for exit warning purposes in addition to vehicle counting, contributing to the safe and smooth operation of parking facilities. 'Features' - Improved detection performance against changes in road surface during rainy weather by using both infrared and radar. - Equipped with IP67 waterproof and dustproof performance, making it effective even in salt damage areas. - Various settings can be configured from a dedicated app (for Android devices), with current settings easily understandable at a glance. - The base dimensions are the same as the previous model "CCS2," allowing for smooth replacement of existing equipment. *For more details, please refer to the product information, catalog download, or contact us.*

On September 15, 2026, we issued a press release regarding the wooden lightweight sheet "Hyper CLT Sheet." The Hyper CLT Sheet is a civil engineering sheet that utilizes CLT (Cross-Laminated Timber) stacked in an orthogonal direction. It can be used in various locations such as temporary roads, access routes, heavy machinery work yards, and material storage areas. The 5×10 version weighs approximately 230 kg, making it relatively lightweight and easy to install, remove, and relocate. Additionally, it offers environmental benefits such as reducing glare and metallic sounds typical of wood, as well as CO2 fixation. Furthermore, it can be proposed for the use of new technologies in public works as a **registered technology with the Ministry of Land, Infrastructure, Transport and Tourism "TH-250021-A."** Through this press release, we aim to expand the new wooden lightweight sheet that combines wood, NETIS, civil engineering, and CLT to more construction sites.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

The "HA-T Series" is an energy-saving automatic door sensor that opens only for those who wish to enter, whether on a busy street or in a narrow passageway. The automatic door opens simply by bringing your hand close, addressing hygiene concerns even in facilities used by a large number of people. You can choose between "Non-vision Mount Type/HA-T401" and "Non-vision Built-in Type/HA-T520" depending on the application and installation location. 【Recommended for such places!】 ☑ Entrance facing a busy corridor ☑ Presence of counters or signs near the door ☑ Buildings facing narrow passages ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors 【Features】 ● Adaptable to various door types with four detection spot settings ● Reduces unnecessary opening and closing, contributing to energy-saving by minimizing wasteful power consumption ● Equipped with a light touch function, allowing the door to open and close just by waving your hand, ensuring hygiene ● Can also be used as a wide detection range non-vision infrared sensor ◎ For more details, please download the materials or contact us.