Strain measurement in thermal shock testing.

Observing the behavior of strain in thermal shock testing! The test materials used are FR-1 and FR-4.

We would like to introduce the "Strain Measurement of Thermal Shock Testing" conducted by our company. A sample with a strain gauge attached was set up in the thermal shock testing device, and the wiring of the strain gauge was connected to an external data logger to record the strain data in real-time during the test. The strain behavior during the thermal shock test was observed for two types of copper-clad laminates, and it was noted that significant strain occurred with changes in temperature. It was found that FR-1 exhibited greater strain compared to FR-4. [Test Conditions] ■ Temperature Cycle: -30°C to 120°C ■ Exposure Time at Each Temperature: 30 min ■ Test Materials - FR-1 Paper Phenolic (Double-sided board) - FR-4 Glass Epoxy (Double-sided board) ■ Strain Gauge: Foil strain gauge for printed circuit boards *For more details, please refer to the PDF document or feel free to contact us.

• Contract Analysis

Not only the joints of electronic components, but also the evaluation of fixed parts such as screws!

At AITES Co., Ltd., we conduct "Thermal Shock Testing." By repeatedly exposing samples to high and low temperatures, not only does stress occur due to thermal effects, but also due to the expansion and contraction of various parts. Repeated stress also adds to the overall stress. This test is conducted not only for the joints of electronic components but also for evaluating fixed points such as screws. 【Main Specifications of the Thermal Shock Testing Equipment】 ■ Internal dimensions: W650×H460×D370mm, Temperature range: -65 to 0/+60 to 200℃ ■ Internal dimensions: W650×H460×D670mm, Temperature range: -65 to 0/+60 to 200℃ ■ Internal dimensions: W970×H460×D670mm, Temperature range: -65 to 0/+60 to 200℃ *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

Applicable to change observation, with support for additional analysis! We evaluate the subject in a time series and non-destructive manner.

During reliability testing, the samples change continuously. Do you have any questions such as "At what point did the crack occur?", "How does the degradation progress?", or "How much has it changed from the initial state?" By combining this with reliability testing, we will evaluate the subject in a time-series and non-destructive manner. 【Features】 ■ Applicable for observing changes in whiskers, migration, pressure resistance, solder evaluation, chemical erosion tests, and aging products in the market ■ Environmental tests and observation frequency will be conducted according to customer requirements ■ Additional analyses such as electrical characteristics, SEM observation, elemental analysis, and cross-sectional observation are also available *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices
• Other inspection equipment and devices
• Contract Inspection

In-Situ Continuous Measurement Reliability Evaluation Testing Service

In-situ continuous measurement reliability evaluation tests involve applying stress while measuring characteristics to conduct reliability assessments. ● Accurate understanding of failure time is possible In a read-out method where samples are taken from a stress environment at a fixed time, failure can only be understood at the timing of the read-out, making it impossible to know the exact failure occurrence time. In-situ measurement allows for an accurate understanding of failure time. ● Detection of recoverable failures is possible Recoverable failures can cause significant issues in the market. In most cases, the read-out method makes it nearly impossible to detect these recoverable failures, whereas in-situ measurement enables the detection of recoverable failures, allowing for accurate judgment and assessment. ● Monitoring of stress application conditions on samples is possible The stress application status and measurement data can be confirmed in real-time.

• Testing Equipment and Devices
• Other inspection equipment and devices
• Contract Inspection

We conduct environmental testing, as well as non-destructive observation and electrical property measurements.

At AITES, we use environmental testing equipment that conforms to standard specifications such as JIS, JEDEC, and MIL, and we accept commissioned testing for reliability evaluation of various electronics products, components, and materials. We offer a range of tests including electrical testing, non-destructive observation, and power cycle testing. 【Environmental Testing】 ■ Highly Accelerated Life Testing ■ Constant Temperature and Humidity Testing ■ Thermal Shock Testing ■ Liquid Bath Thermal Shock Testing ■ Temperature and Humidity Cycle Testing ■ In-Situ Continuous Measurement Reliability Evaluation Testing Service *For more details, please refer to the PDF materials or feel free to contact us.

• Analytical Equipment and Devices
• Analysis Services

Dear Sir/Madam, I hope this message finds you well and thriving. I would like to express my sincere gratitude for your continued support. We would like to inform you that our company will be closed for summer vacation during the following period: ■ Summer Vacation Period From Saturday, August 8, 2026, to Sunday, August 16, 2026. We will resume normal operations on Monday, August 17, 2026. Inquiries received during the vacation period will be addressed sequentially after the start of business. We apologize for any inconvenience this may cause and appreciate your understanding.

What is a sealed product air leak test device? It is an air leak test device that inspects the airtightness, sealing performance, and waterproofness of electrical equipment and packaging containers (cosmetics, food). It tests for leaks in products such as smartphones, tablet devices, keyless switches, wristwatches, bottle containers, and cosmetic containers (eyeliner, mascara).

Fukuda's new flagship model. - Masterless type (FLA-0200 series) - General type (FLA-0201 series) Two models of air leak testers. With the mastering correction function, high-precision measurements can be achieved in a short time. Please take a look at the catalog.

Fukuda Co., Ltd., which develops, manufactures, and sells leak testing equipment to inspect airtightness and sealing performance, provides a technical document that clearly explains the methods and theories of airtight testing, titled "Technical Manual." We are offering it as a PDF file. Please take this opportunity to download and view it!

What is an Air Leak Tester? An "Air Leak Tester" is a device that pressurizes the inside (or outside) of a sealed workpiece with air and determines the presence of leaks based on pressure changes. When a master with no leaks and a workpiece with leaks are pressurized, the pressure on the workpiece side decreases, creating a pressure difference between the two. By measuring this pressure difference, the presence of leaks can be determined. Generally, differential pressure air leak testing is widely used, but Fukuda also offers products that utilize direct pressure leak testing and flow meters according to the leak rate, in addition to differential pressure leak testers. Since the air leak tester uses air as the measurement medium, it incurs no running costs and is environmentally friendly.