Product condition and underfloor environment of the Dry Pro Type-C after approximately 2.5 years of use.

Contributes to the prevention of condensation and mold under the floor. A new model compatible with the foundation packing method has been introduced.

The "DRY PRO" Ver3 is an electronic dehumidifying and blowing unit for underfloor use, combining a Peltier cooling device with a dedicated stirring and diffusion-type blower. In addition to the diffusion-type model "TYPE-D" for foundation insulation construction, a new model "TYPE-C" compatible with foundation packing construction has been added to the lineup. It can dehumidify even in areas where moisture tends to accumulate by stirring a wide range of air. It helps suppress moisture and condensation under the floor, contributing to the prevention of mold, pests, and decay fungi in wooden parts under the floor. Furthermore, with the version upgrade in June 2024, a powerful dehumidification operation mode will be added. The surrounding temperature range for dehumidification operation (low-temperature dehumidification operation range) has been expanded, allowing operation at surrounding temperatures down to 5°C. 【Features】 ■ Easy installation with a φ22 drainage hole (no drainage pump required) ■ Automatic operation possible with a dedicated indoor controller ■ The direction of the aluminum duct of the blower can be set freely ■ Dehumidification capacity of 1800mL per day (depending on conditions) ■ Uses fluorine-free electronic cooling technology ■ Compatible with underfloor flooding sensors (optional) *For more details, please refer to the PDF document or feel free to contact us.

• Dehumidifier

Measures against condensation in summer! Condensation and corrosion within wall structures are often difficult to detect.

In 2020, the "mandatory energy-saving standards for housing" are scheduled to be implemented, and it is expected that Japanese homes will increasingly aim for high airtightness and high insulation. However, at the same time, measures against condensation during the summer must be considered. In a site where glass wool was filled using the 2x4 construction method and a vapor barrier was installed on the interior side, significant corrosion due to condensation occurred. It is believed that the interior became hot and humid, leading to condensation as it was cooled by the air conditioner on the inside. The hold-down hardware also showed white mold, and if corrosion progresses like this, it will pose problems for the durability of the building. This type of summer condensation particularly occurs in regions with high temperatures and humidity, like Japan. Therefore, it is necessary to implement sufficient measures against winter condensation while simultaneously preventing summer condensation. *For more details, please refer to the PDF document or feel free to contact us.

• others

【Demo available】Powerfully disperses dehumidified air over a wide area with strong airflow! Easily installable by making a Φ22 hole for the drain pipe.

The "Dry Pro" electronic dehumidifying and air-blowing unit for underfloor use combines a Peltier cooling device with a diffusion-type blower to dehumidify the entire underfloor area, suppressing the occurrence of moisture and condensation! This system is designed to dehumidify the space between the foundation and the floor, suitable for housing construction methods that lack ventilation openings. On humid days during the rainy season or summer: ● Powerful dehumidification with a large airflow of 1800 ml/day Effectively eliminates moisture and condensation, and is effective against mold, pests, and decay fungi in underfloor wooden components. [Features] ■ Easy installation by simply drilling a Φ22 drain hole! ■ Circulates dehumidified air widely with the blower ■ Equipped with fitonchid, which has deodorizing effects, as standard ■ Patent and design applications pending ■ Fully automatic operation with a dedicated controller *Please note that [demo visits] may not be available in certain regions. Thank you for your understanding in advance. *For more details, please refer to the PDF materials or feel free to contact us.

• Dehumidifier

The cause is a large amount of water vapor! The challenge is how to remove humidity and suppress mold and decay.

Foundation insulation is a method of insulating the foundation that faces the outside air. The period when the risk of condensation and mold is highest with foundation insulation is from June to September of the first year after completion. The main cause is the large amount of water vapor that comes from the concrete floor. Especially, wood that contains a lot of moisture significantly deteriorates in strength, so it is important to be cautious considering durability against earthquakes and typhoons. As a solution to these moisture problems, our company has developed a dedicated underfloor dehumidifier called "Dry Pro." It effectively eliminates moisture and condensation, and is useful for preventing mold, pests, and decay fungi in the underfloor wooden components. (Patent and design application pending) 【Features of Dry Pro】 ■ Dehumidification capacity of approximately 400-600cc per day on humid days during the rainy season and summer ■ Circulates dehumidified air widely using a blower ■ Quiet design: 45/44dB ■ Equipped with fittonia, which has deodorizing effects as standard *For more details, please refer to the PDF document or feel free to contact us.

• Dehumidifier

After about one month, a drier condition (wood moisture content 12%) was confirmed!

"Dry Pro" is a floor dehumidifying blower that effectively eliminates moisture and condensation, and is useful for preventing mold, pests, and decay fungi in the wooden parts under the floor. Assuming the early stages of new construction for homes with foundation insulation methods, 36 liters of water were sprinkled on the foundation under each building, and dried wood (cedar) was installed to measure the moisture content of the wood and the humidity under the floor. As a result, the buildings where this product was installed gradually dried out by repeatedly operating the dehumidification process every day, and after about two months, an average of approximately 70% RH in a dried state was confirmed even outside of the dehumidification operation hours. [Experiment] ■ Test House A - Floor area approximately 10 tsubo - Foundation insulated underfloor (Dry Pro installed) ■ Test House B - Floor area approximately 10 tsubo - Foundation insulated underfloor (no dehumidifying blower) *For more details, please refer to the PDF document or feel free to contact us.

• Dehumidifier

We have added a new **"Glossary"** to the Hyper CLT sheet website. In the civil engineering and construction industries, there are many specialized terms such as "CLT," "NETIS," "temporary roads," and "wooden lightweight sheets." Therefore, we have introduced related terms in an easy-to-understand manner so that those who are encountering Hyper CLT sheets for the first time can understand the products and technologies. Hyper CLT sheets are wooden lightweight sheets for civil engineering that utilize wood CLT and are registered under the Ministry of Land, Infrastructure, Transport and Tourism's NETIS technology as **"TH-250021-A."** We hope that by not only conveying the features of the product but also sharing the underlying technologies and terminology, users will feel a closer connection to Hyper CLT sheets. We will continue to enhance our website and provide clear information related to wood, NETIS, civil engineering, and CLT.

Hotron Inc. has launched its new product, the "Vehicle Count Sensor CCS3"! This product is a ceiling-mounted sensor that combines infrared and radar technology. It reliably detects vehicles in both directions with a single unit, accommodating traffic during congestion and vehicle passing, thus achieving efficient occupancy management in large parking lots. Additionally, it can be utilized for exit warning purposes in addition to vehicle counting, contributing to the safe and smooth operation of parking facilities. 'Features' - Improved detection performance against changes in road surface during rainy weather by using both infrared and radar. - Equipped with IP67 waterproof and dustproof performance, making it effective even in salt damage areas. - Various settings can be configured from a dedicated app (for Android devices), with current settings easily understandable at a glance. - The base dimensions are the same as the previous model "CCS2," allowing for smooth replacement of existing equipment. *For more details, please refer to the product information, catalog download, or contact us.*

On September 15, 2026, we issued a press release regarding the wooden lightweight sheet "Hyper CLT Sheet." The Hyper CLT Sheet is a civil engineering sheet that utilizes CLT (Cross-Laminated Timber) stacked in an orthogonal direction. It can be used in various locations such as temporary roads, access routes, heavy machinery work yards, and material storage areas. The 5×10 version weighs approximately 230 kg, making it relatively lightweight and easy to install, remove, and relocate. Additionally, it offers environmental benefits such as reducing glare and metallic sounds typical of wood, as well as CO2 fixation. Furthermore, it can be proposed for the use of new technologies in public works as a **registered technology with the Ministry of Land, Infrastructure, Transport and Tourism "TH-250021-A."** Through this press release, we aim to expand the new wooden lightweight sheet that combines wood, NETIS, civil engineering, and CLT to more construction sites.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

The "HA-T Series" is an energy-saving automatic door sensor that opens only for those who wish to enter, whether on a busy street or in a narrow passageway. The automatic door opens simply by bringing your hand close, addressing hygiene concerns even in facilities used by a large number of people. You can choose between "Non-vision Mount Type/HA-T401" and "Non-vision Built-in Type/HA-T520" depending on the application and installation location. 【Recommended for such places!】 ☑ Entrance facing a busy corridor ☑ Presence of counters or signs near the door ☑ Buildings facing narrow passages ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors 【Features】 ● Adaptable to various door types with four detection spot settings ● Reduces unnecessary opening and closing, contributing to energy-saving by minimizing wasteful power consumption ● Equipped with a light touch function, allowing the door to open and close just by waving your hand, ensuring hygiene ● Can also be used as a wide detection range non-vision infrared sensor ◎ For more details, please download the materials or contact us.