The number of NETIS registered products has increased to 11!

Patent granted!! Formwork removal strength management system that can estimate initial strength 【NETIS registration number: KK-200048-A】

This is a formwork removal strength management system that estimates the initial strength based on the amplitude of ultrasonic waves propagating through the cured concrete. It was registered in NETIS in 2020 (registration number: KK-200048-A). Continuous measurements can be taken from the time of concrete pouring, allowing for the estimation of initial strength at any given point and confirming the achievement of the specified strength, thus enabling formwork removal.

• Strength Testing Equipment

Completely non-destructive corrosion inspection of rebar in floor slabs is possible! 【NETIS registration number: OK-170001-A】

High Bright is a ground-penetrating radar solution specialized in the early detection of deterioration in concrete bridge decks. It features a 16-channel array antenna (approximately 1 meter wide), allowing for a large area to be measured at once. The software designed specifically for bridges (GRED HD BRIDGE) enables detailed 3D fault exploration and provides three types of processing results: - Rebar corrosion map - Humidity map - Cover thickness map [Features] - Utilizes a 2GHz, 16-channel array antenna for detailed 3D fault exploration - The array antenna, measuring 1 meter in width, allows for a larger area to be measured at once, reducing inspection time to 1/16 compared to a single antenna radar [Processing result display with bridge-specific software - GRED HD -] GRED HD Bridge is designed to provide a rapid and effective bridge deck evaluation tool. The software can automatically detect rebar position, depth, asphalt thickness, and concrete slab thickness.

• Testing Equipment and Devices

By using special sealing materials, non-destructive testing can be achieved on any surface of the structure, including the top, bottom, and sides! [NETIS Registration Number: QS-170036-A]

A special sealing material is applied to the surface of the measurement area, and a double chamber is pressed against it. The outer chamber is evacuated to create suction, and then air (in the case of a permeability test) or distilled water (in the case of a water permeability test) is pressurized in the inner chamber, allowing it to permeate into the concrete using a non-destructive testing method. From the surface permeability coefficient P value, which can be measured at the construction site of concrete structures, it is possible to non-destructively inspect properties such as water tightness and durability, which are closely related to deterioration involving water.

• Testing Equipment and Devices

3D analysis using dedicated software Latest model equipped with cutting-edge technology 【NETIS registration number: CB-150009-A】

◆◇◆ Live demonstrations and on-site presentations are available. Please feel free to contact us. ◆◇◆ The "TSP303" is a cutting-edge tunnel face exploration device developed by Amberg Technology, a company specializing in tunnels and underground structures with 20 years of experience. This is the latest model in the TSP series, which has achieved numerous results both domestically and internationally. Based on the experience gained from the "TSP202," "TSP203," and "TSP203 plus," it provides more accurate and clearer data.

• Other inspection equipment and devices

Quick and easy measurement of the unit water content in fresh concrete is possible! 【NETIS Registration Number: QS-180032-VE】

"PICO-BT / SONO-WZ" is a testing device that allows for easy and rapid measurement of the unit water content in fresh concrete. It can measure with the same accuracy as a heating drying oven, regardless of the type of fresh concrete. By inputting the density of the concrete into this device, it is possible to measure the unit water content (kg/m³). The measurement time is quick, typically around 2 minutes for 5 measurements. *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

Completely non-destructive and very easy measurement of the air permeability of surface concrete! [NETIS Registration Number: QS-150029-VE]

The performance of concrete varies significantly depending on the concrete mix, placement method, type of formwork, and curing method. Therefore, verifying the quality of the surface concrete (cover concrete) is extremely important when considering durability performance. According to Swiss standard SIA 262:2003, "The impermeability of the cover concrete must be checked by permeability tests on cores taken from the structure or from the structure itself." Permatol AC+ can measure the air permeability of surface concrete completely non-destructively and very easily.

• Other inspection equipment and devices

Used for measuring post-rolling density and void ratio during asphalt laying!

No adjustments for temperature or humidity are necessary; you can easily take measurements just by pointing it at the measurement location. Its handy size allows for one-handed operation, making it easy to carry. Measurement data can be saved, and the saved data can also be printed.

• Other measurement, recording and measuring instruments

Unlike previous pull-out tests, testing can be conducted with the wall's concrete in its original position. 【NETIS Registration Number: QS-190031-A】

【Features】 ■ Complies with NEXCO Test Method 726 2009 It complies with the NEXCO test method "726 2009" and is used in many field applications. ■ No individual differences in test results Stable penetration force is achieved through air pressure, resulting in no individual differences in the results. Additionally, equipment calibration can be easily verified using a calibration test anvil. ■ Testing possible in situ There are no restrictions on the penetration direction, allowing for testing of concrete sprayed on walls in its original position. ■ Wide range of strength estimation possible By using two types of pins with different penetration resistances, strength estimation is possible in the range of 0.1 to 26 N/m².

• Other inspection equipment and devices

Concrete compressive strength testing machine capable of real-time sharing of measurement values 【NETIS registration number: QA-200024-A】

It is one of the rebound methods that estimate the compressive strength based on the height to which a hammer rebounds after striking concrete (rebound value: R value), and it is a non-destructive testing method that allows inspection without damaging the structure. It is also used for estimating the strength of rock formations in addition to concrete. The compressive strength estimation formulas presented at various academic societies are all based on test data from the Schmidt concrete test hammer. Schmidt Live automatically processes troublesome average values and angle corrections, and it also has a moisture content correction function. Since standards such as the JSCE G-504 are also registered, strength estimation is easy. It has evolved into a type that anyone can easily use without individual differences.

• Testing Equipment and Devices

Move the measurement head left and right to scan the entire face of the tunnel! 【NETIS Registration Number: QS-190038-A】

Using cutting-edge ArcSAR synthetic aperture technology, the measurement head moves left and right every 15 seconds to scan the entire face. The measurement accuracy is extremely high, capable of measuring within 0.1mm. 【Features】 - 24-hour monitoring of the face - Scans the face every 15 seconds (5,760 scans in 24 hours) - Measurement accuracy of 0.1mm - High-precision detection of minute displacements and behaviors before rockfalls - Scan data is processed in real-time and displayed on a tablet - Detects initial fluctuations and issues alarms - Data can be accessed remotely

• Testing Equipment and Devices

Automatically controls and optimizes the screed function of asphalt pavers! [NETIS Registration Number: QS-200034-A]

The Mat Tracker tracks the edges of paved asphalt lanes and automates the movement of the paver's side plates to ensure consistent overlap at joints. To ensure overlap, the screed foreman must always pay attention. By fulfilling this role, the Mat Tracker allows the operator to have time to perform other tasks. It also reduces the frequency with which the operator has to step outside the screed, significantly decreasing the risk of accidents. 【Features】 - Automation of screed side plate adjustment - Improved quality of joints - Density improvement through perfect lane overlap - Reduction of operator workload

• Testing Equipment and Devices

We have released a new video on our company’s YouTube channel. The theme of this video is "The World of Amino Acid-Based Shampoos." Amino acid-based shampoos have become popular in recent years, but the lather, feel, and finish can vary greatly depending on the cleansing ingredients used. In this video, we clearly explain the changes in user experience based on the differences in cleansing ingredients by comparing two types of amino acid-based shampoos. We hope you can use this as a hint for developing original shampoos and differentiation.

[To the owners of parking lots and parking lot construction companies] "I’m worried about not colliding with pedestrians when exiting the parking lot..." Among vehicle entrances to parking lots, stores, residences, and factories, those particularly facing sidewalks or roadways are expected to pose risks of dangerous incidents such as collisions with pedestrians or between vehicles. To alleviate such concerns, Hotron proposes a [Vehicle Exit Warning Sensor] that detects vehicle departures using various sensors and alerts the surroundings with LED lights and buzzers. The device consists of a simple configuration of "Sensor" + "Controller" + "Switching Power Supply (24V)" + "LED Rotating Light." *Please note that a separate control panel is required to include the controller and switching power supply (24V) when using the exit warning system. *We kindly ask that customers arrange for the switching power supply (24V), LED rotating light, control panel, circuit breakers, etc. Since it can be retrofitted, it can also be used for existing parking lot entrances. We hope this will contribute to safer vehicle passage for everyone. ◎ For more details, please contact us or download the catalog.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repair without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

Hotron, which manufactures and sells sensors, provides bed exit sensors for hospitals, nursing, and care facilities. Hotron offers easy-to-understand video guidance on how to use the bed exit sensors wirelessly and how to set up device connections! ▼ Video Manual (YouTube) https://www.youtube.com/playlist?list=PLNVA4mTrZDqtJa6MfFRZQxwtfCSnAfxVy 【Bed Exit Sensors】 ○ Non-contact infrared sensor, simply place it - Pole-kun HB-H1 ○ Mat sensor, foldable thin mat - Mat-kun HB-UST ○ Body movement call - Ugo-kun HB-TV3 ○ Body movement call for wheelchairs - Ayumi-chan HB-WTV3 【Options】 ○ Nurse call linked wireless set - Wireless set (transmitter/receiver) HB-RS/HB-RJ ◎ For more information about the products, please contact us or download the catalog.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding methods for repairs can cause changes in the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.