[Improvement Case] The catalog for the GME-S series mist collector, which does not accumulate cut glass or abrasive particles internally with its "One-Way Flow" system, is now available!

We have successfully reduced the maintenance frequency of the mist collector in processes such as polishing, where not only oil mist but also chips and abrasive particles are generated simultaneously.

This is an example from a grinding factory. In grinding, not only oil mist but also chips and abrasive particles are generated together. Therefore, traditionally, even if a mist collector was installed, it would quickly become clogged, allowing mist to spread throughout the factory. 【Proposed Solution Example】 ■ Traditional Method - Use of filter-type mist collectors ■ Issues - The mist collector's filter quickly clogs due to the suction of oil mist containing chips and abrasive particles - Frequent maintenance of the mist collector is required - Oil mist disperses, causing odor and haze ■ Ideal Condition - The mist collector's filter does not clog even when sucking in oil mist mixed with chips and abrasive particles - Oil mist is effectively collected and does not disperse within the factory - Longer maintenance cycles with reduced labor ■ Apiste's Proposal - Installation of the GME-S series mist collector, which adopts a "one-way flow system" that does not accumulate chips and abrasive particles internally, allowing for longer maintenance cycles ■ Benefits - Reduction in labor due to extended maintenance cycles - Environmental improvement due to reduced mist leakage outside the processing machine

• Oil Mist Collector

Achieving a reduction in man-hours due to the extension of maintenance cycles, a decrease in mist leakage outside the processing machine, and improvement of mist within the factory!

【Proposed Solutions】 ■Conventional Methods 　・Using filter-type mist collectors 　・Using cyclone-type mist collectors ■Issues 　・Frequent maintenance required for mist collectors 　・Oil mist disperses, causing slippery factory floors ■Ideal Condition 　・Oil mist is effectively collected and does not disperse within the factory 　・Longer maintenance cycles with reduced labor ■Our Proposal 　・Install the GME series mist collectors with longer maintenance cycles 　・Recalculate the required airflow for each processing machine and survey the current airflow ■Benefits 　・Reduction in labor due to extended maintenance cycles 　・Decrease in mist leakage outside processing machines by maintaining airflow 　＋α Achieve significant energy savings (※Models equipped with energy-saving mode) ※For more details, please refer to the related product catalog or feel free to contact us.

• Oil Mist Collector

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repair without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

Thank you very much for visiting our company website and catalog, and for your interest in our diesel engine generators. From customer surveys, we received the following feedback as the most common requests: - I want to see the actual generators that have been installed. - I want to see the operation under actual load. - I want to hear the opinions of companies that have installed the generators. - I want to see the operating generators before making a purchase. After all, it’s understandable to be concerned about purchasing a generator without seeing the actual unit first, right? As the saying goes, "Seeing is believing..." we will be holding this tour. It is located in that area of the Kanto region where the maximum temperature exceeds 40°C during the summer. We successfully operated it again this summer, so we are confident about handling the heat (sweat)... Furthermore, it has been confirmed that it is "fuel-efficient" due to the world-leading "Scania engine" installed. This will surely help reduce daily operating costs. Please note that while we will provide kind and courteous assistance, the meeting point and dispersal will be at the site (transportation costs and other expenses will be borne by the customer), so please understand this in advance. Contact: Kaneko

The non-contact beam touch sensor "HA-T401/HA-T520" has a compact detection range, making it an ideal automatic door sensor for installation on automatic doors facing narrow corridors or busy streets. Depending on the application and installation location, you can choose between "non-vision mounting type" and "non-vision built-in type." 【Features】 ● With the beam touch sensor, you can open and close the automatic door simply by bringing your hand close without touching it, ensuring hygiene. ● Depending on the installation environment, such as single sliding or bi-parting doors, the detection range can be set in four ways: left, center, right, with 4 spots and 12 spots settings. ● Two types of activation row settings are available to reduce unnecessary opening and closing of the automatic door due to cross traffic, contributing to energy-saving effects. ● The touch switch and infrared sensor are integrated, allowing for a switch between beam touch and infrared sensor modes with a single model. 【Recommended for such places!】 ☑ Entrances facing busy corridors ☑ Counters or signs near the door ☑ Buildings facing narrow corridors ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors ◎ For more details, please download the materials or contact us.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.