Create/measure long time differences with picosecond (ps) resolution! ⇒ Generate time differences in picoseconds with the T560 delay/pulse generator and measure time differences in picoseconds with the MCS8A TDC/TOF.

This explains the configuration of creating a time difference with the T560 delay/pulse generator and measuring the time difference with the MCS8A multi-stop TDC/TOF.

◆T560 Delay/Pulse Generator - Delay time and pulse width can be specified individually for 4 channels, with settings possible in 10ps increments up to a maximum of 10 seconds. - Input/output delay (insertion delay): 21ns - Maximum trigger rate: 16MHz ◆MCS8A Multi-Stop TDC/TOF - An 8-input digitizer capable of recording multiple event times. - The time difference between START and STOP can be detected with a resolution of 80ps for up to 8.3 days. - STOP can be detected on the rising edge, falling edge, or both edges. - The threshold levels for START and STOP can be set in 1mV increments within the range of -1 to +1.5V. - A multi-event time digitizer with 80ps per time bin and no dead time. ◆MPA4T Combined TDC/TOF and Multi-Parameter MPA - A 5-input digitizer derived from the MCS8A, with 100ps per time bin. - Equipped with an 8-channel ADC input port, functioning as a multi-parameter data acquisition system (MPA). ⇒ Operates as a high-speed list mode system. ⇒ Each ADC input can also connect to multi-scalers or TOF devices.

• Radiation detector
• Other inspection equipment and devices
• Analytical Equipment and Devices

You can set the delay time and pulse width for each of the 4 channels in increments of 10 ps. The input/output delay is only 21 ns, generating precise output pulses.

The T560 series is a family of compact digital delay generators designed for embedded applications in OEM settings. ◆ TTL level delay output × 4 channels Each channel's delay time and pulse width can be set individually ◆ Delay time and pulse width can be set in 10ps increments Configurable up to a maximum of 10 seconds ◆ Input/output delay (insertion delay): 21ns Maximum trigger rate: 16MHz ◆ High-precision phase-locked system with low jitter Maintains delay accuracy with a crystal clock Eliminates uncertainty due to external errors ◆ Time base from an internal crystal oscillator Ability to synchronize with an external clock ◆ DDS synthesizer for internal trigger rate ◆ Operates with a standard +12V single power supply ◆ Equipped with a standard RS-232 serial interface Ethernet option also available ◆ Custom versions available for OEM packages or internal boards only

• Signal Generator

Time difference measurement TDC ⇒ The speed of the phenomenon can be measured. It detects the time difference between the START signal and eight types of STOP signals with a resolution of 80 ps.

Up to 8 types of event times can be recorded. It is a multi-event time digitizer (TDC) with 80 ps per time bin and no dead time. **Features** - It can detect pulse widths with an accuracy of 80 ps and calculate the area and height of the detector's pulses. - It can detect overlapping multiple events. - The state changes of STOP events can be evaluated at a rate of 12.5 GHz. - It achieves a constant throughput of 240 MB/s with a USB 3.0 interface. - An optional oven-stabilized clock for stable oscillation is also available.

• Time-frequency measurements
• Other electric meters

This is product information from Cremat, focusing on charge-sensitive preamplifiers for capacitive sensors.

Detectors and sensors that detect charge (charge) proportional to the strength of energy include APD (Avalanche Photodiode), PMT (Photomultiplier Tube: Photomultiplier), and MEMS capacitive accelerometers, among others. In charge-sensitive preamplifiers, the output obtained is proportional to the amount of charge received from the detector. They are categorized into four types based on differences in gain. Gaussian shaping amplifiers shape long tail pulse waveforms into Gaussian function waveforms. They are divided into eight types based on differences in shaping time. Baseline restorers are modules that correct baseline shifts and are effective for high count rate input pulses. Using evaluation boards and aluminum housings makes it easy to verify inputs from the target detectors. The finished products of charge-sensitive preamplifiers include those compatible with the high voltage bias of detectors and specialized products for photomultipliers and SiPMs. The finished products of Gaussian shaping amplifiers are available in eight types with different shaping times.

• Amplifier
• Radiation detector

In civil engineering sites such as mountainous areas and construction sites, it may be necessary to use wooden boards on slopes or inclined access roads. Hyper CLT boards are civil engineering materials utilizing wood CLT, which can be laid not only on flat ground but also on sloped terrain. They can be used for temporary roads, access routes, heavy machinery entry paths, and measures against muddy conditions, creating a driving environment that takes advantage of the unique surface characteristics of wood. The 5×10 board weighs approximately 230 kg, and the 5×20 board weighs about 460 kg, making them lightweight and easy to install and remove even with small machinery, which is a notable feature for maneuverability in narrow sites. This wooden board is registered as a technology under the Ministry of Land, Infrastructure, Transport and Tourism's NETIS system as "TH-250021-A," and can also be utilized for safety measures and innovative ideas in public works.

Metal cracks are one of the concerns in equipment maintenance operations. Repairs using conventional welding methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" or "secondary damage." Hinode Waterworks Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be performed even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

● To determine the sealing and waterproofing of sealed products based on pressure changes, it is not necessary to conduct tests that involve spraying water on the product or immersing it in water. ● Once the product is placed in a dedicated fixture within the inspection device, waterproofing can be quantitatively confirmed through automatic measurement. ● The target product size is W 300 × D 210 × H 100 mm or smaller. ● The target products include automotive cameras, smartphones, ECUs, small motors, and other packaging containers, and are effective for any products that require confirmation of sealing, waterproofing, and airtightness. ● For product specifications and details, please contact us.

The inspection targets of the "MSX-7003 series" are relatively large electronic devices. 【Inspection Targets】 - LED - Optical devices - High-frequency devices - Power semiconductors - IR sensors - Gyro sensors - Angular velocity sensors - Electrolytic capacitors, etc. The transport system is designed based on "pallet to pallet" to accommodate various types of work. The following three processes are performed automatically by the airtight inspection device: - Helium bombarding - Gross leak test - Fine leak test For packaged products smaller than 10 mm on each side, the work is set up using pallets or trays, followed by helium bombarding ↓ Then transported to the leak test process through high-speed handling ↓ Going through a continuous process from the gross leak test to the fine leak test ↓ And finally, discharged onto a pallet through high-speed handling. It also supports inline operations (the height of the pass line is 940 mm). Please watch the YouTube video from the link below.