Broad Discのメーカーや取扱い企業、製品情報、参考価格、ランキングをまとめています。
イプロスは、 製造業 ・ BtoB における情報を集めた国内最大級の技術データベースサイトです。

Broad Disc - メーカー・企業と製品の一覧

Broad Discの製品一覧

61～75 件を表示 ／ 全 83 件

表示件数
0397 Prevention of bridge formation of dust containing glass fibers

0397 Prevention of bridge formation of dust containing glass fibers

Prevention of dust containing glass fibers! An example of applying a blow disk to the hopper section of a dust collector.

This is a case where a blow disk was adopted for application to new equipment. The application location is the dust collector hopper section. Since the blow disk injects air along the inner surface of the hopper, it is generally the case that the effectiveness does not change significantly even if the installation position is slightly off. The key point this time is that due to the properties of the target material, the air pressure used is high, the air ON time is short, and air aeration is performed in a pulsed manner. [Overview] ■ Hopper approximate dimensions: 2000×2000 (discharge section 200×200) ■ Blow disk arrangement - 3 units per 4 sides, with 1 unit on the lower level and 2 units on the upper level per side (However, only 2 units are installed on one side due to the inspection port) - Both lower and upper levels are positioned quite low, near the discharge port * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous implementation examples. You can check them from the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0409 Using a fertilizer mixing scale

0409 Using a fertilizer mixing scale

We recommend testing by borrowing the equipment, and you were able to confirm its effectiveness!

This is an introduction to a case where a customer who has been using our equipment for some time expressed the desire to install an absolute blow disk because the target material has a high moisture content and also contains oil. When we first made contact, regardless of whether they would adopt our equipment, we recommended testing it by lending it out, which allowed them to confirm its effectiveness. Since then, they have been using our products repeatedly. 【Overview】 ■ Installed under a two-way switching damper ■ Hopper size is approximately 1000×500 ■ Quantity: 4 units × 2 hoppers ■ Product specifications: Blow disk BD-15S-B, 8 units *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous implementation examples, which can be checked via the link below.

  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0411　サービスステーション（セメント）向けに納入

0411　サービスステーション（セメント）向けに納入

稼働後の状況はもちろん良好！　プラント設備工事業者様にご採用いただいた事例のご紹介です

SS向けの案件で、従来使用していた「〇〇レーション」というブリッジ防止機器が調達できないとのことで代替え用としてお問い合わせいただきました。 きっかけは、代替品としてのお問い合わせでしたが、ご使用条件などをもとに、当社ブローディスクの配置や設置方法についてお打合せを進めると、設置数量・機器コスト面・取付工事の面などでメリットが生まれることが判明。 稼働後の状況は、もちろん良好でユーザー様にもご満足いただいています。 【概要】 ■直径3800φサイロの下方に（今回はかなり下のほうのみです） 　4個×2段に配置 ■製品仕様：ブローディスク BD-15S-B 8個 ※詳しくはPDF資料をご覧いただくか、お気軽にお問い合わせ下さい。 ※当社ホームページに多数の実施例を掲載しています。 　下記リンクよりご確認いただけます。

  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0412 Measures to Prevent Clogging of Tapioca Flour

0412 Measures to Prevent Clogging of Tapioca Flour

The result is OK! This is a project that adopted the load disk (mini) and controller.

This is an introduction to a case where the powder did not drop at all from the hopper, and despite various attempts, nothing worked. Knockers and vibrators were not effective, and a homemade aeration system created by modifying the piping also had no effect. We received a call expressing interest in trying a blow disk. After discussing the situation and receiving examples of what did not work from the customer, we decided on the arrangement and quantity of our equipment, lent out product samples, and conducted a trial. The result was positive; the blockage was resolved, and the customer decided to adopt the blow disk (mini) and controller. [Overview] ■ Material: Tapioca flour (also corn starch) ■ Hopper diameter: 300φ ■ Discharge diameter: 100φ * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them out via the link below.

  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0419 Resolving blockages of crushed material + virgin raw materials

0419 Resolving blockages of crushed material + virgin raw materials

We have been evaluated as having resolved the issue of clogging, and you have adopted our equipment.

This is a case adopted by a business primarily engaged in the molding of resin products. When introducing a new hopper, the mixing ratio of crushed material and virgin material was changed, which led to the occurrence of bridging that had not happened with this material before. They contacted us expressing a desire to try the BroaDisk. After receiving information about the hopper and materials, we promptly decided to send a demo unit. After providing the ideal arrangement for the BroaDisk (mini), the user experimented with various air pressures and aeration times, and they evaluated that the issue of clogging was resolved, leading to the adoption of our equipment. 【Overview】 ■ Hopper diameter: Approximately 300φ ■ Discharge diameter: Approximately 30φ ■ Inclined section: More gentle than typical ones * For more details, please refer to the PDF materials or feel free to contact us. * Our website features numerous implementation examples. You can check them from the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0429 Promote the discharge of fly ash

0429 Promote the discharge of fly ash

We have adopted a blow disk to improve the emission defects occurring on the fly ash side!

This is an inquiry made through a trading company regarding an issue at an existing plant. A single round silo is divided into two sections by an internal partition, and this equipment was introduced to improve the discharge issues occurring on the fly ash side of one half. The plant originally had aeration nozzles installed, but since that was not effective, this equipment was adopted. After the introduction of this equipment, it has been operating without any problems. 【Overview of Blower Disk Installation】 ■ 8 standard blower disks installed in the silo section (Arranged in 3 tiers: 3 + 2 + 3) ■ 2 standard blower disks installed in the chute section (The chute section has sufficient slope, so 2 disks are installed at different heights) * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0425 Solving the bridge for sawdust (fuel)

0425 Solving the bridge for sawdust (fuel)

This is an example of installing a Brody disk to address the issue of poor discharge of sawdust.

A machinery device manufacturer has consulted us, expressing concerns about ongoing troubles with past projects, asking if there is anything that can be done. The customer requested to install not only at the bottom of the hopper but also at the top, based on their own experience, and we installed 8 units. After installation, we received feedback that the discharge issues were completely resolved. 【Overview】 ■ Hopper to be installed ・1200×1200 (Capacity: 2.5m³) ・2-sided slope (slope 60°) ・Screw discharge 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of the risk of foreign matter contamination, as well as strength and durability. The silicone disk of this equipment is exceptionally strong and durable. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please refer to the PDF materials or feel free to contact us. *Our website features numerous case studies. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0498 Prevention of clogging of flake-shaped chemical products

0498 Prevention of clogging of flake-shaped chemical products

The discharge issues have been resolved, and operations are running smoothly! It is possible to provide examples of arrangements and controls that are considered suitable, including costs.

Here is a case study of a major chemical company that adopted our solution. Despite the hopper's apex angle being approximately 30° (with an inclination of about 75° from the horizontal plane), they consulted us due to difficulties in discharge. Using a hopper that the customer had (not an actual machine), we conducted tests with our loaned equipment, and after subsequent discussions, they adopted our BroaDisk. After the adoption, the discharge issues were resolved, and it has been operating smoothly. 【Case Overview】 ■ Material: Chemical product flakes (approximately 10mm, easily breakable flakes) ■ Hopper ・Diameter: φ1800 ・Discharge diameter: 200A ■ Equipment arrangement: A total of 12 units installed in 4 tiers, with 3 units placed every 120° on the same circumference. *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0537 Residual measures for the dust collector hopper section

0537 Residual measures for the dust collector hopper section

Since configurations are important, we kindly ask customers who are interested to please consult with us, even if it may be a bit of a hassle!

A blower disk has been installed to prevent residuals that occur at the discharge bridge and in the four corners of the existing dust collector. This equipment has a simple structure, but it generally offers sufficient effectiveness. However, since the arrangement is important, we encourage interested customers to consult with us, even if it may be a bit of a hassle. We can provide specific advice. 【Product Specifications】 ■ Blower Disk: BD-15S-B, 8 pieces 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign matter contamination. The silicone disk in this equipment excels in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF materials or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0547 Measures to prevent clogging of talc (discharge section φ50)

0547 Measures to prevent clogging of talc (discharge section φ50)

The blockage near the discharge section has been resolved! Please feel free to consult us about specific arrangements and controls.

You are already using BroaDisk in other material tanks. This was a consultation from a user. They requested, "The diameter of the hopper discharge section is small, causing bridging, so I would like to try the BroaDisk Mini and request to borrow the equipment." After discussing various conditions, we recommended the arrangement and quantity (4 BroaDisk Minis) and sent the equipment. As a result of the test, the clogging near the discharge section was resolved, but there were concerns about rat holes above that, and ultimately, 4 BroaDisk Minis were installed near the discharge section, with 2 BroaDisks placed above them. 【Product Specifications】 ■ BroaDisk: BD-15S-B 2 units ■ BroaDisk Mini: BD-08S-B 4 units ■ Controller: C-SV4 1 unit *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0550 Applicable to the hopper for resin compound + glass powder.

0550 Applicable to the hopper for resin compound + glass powder.

Testing conducted by the user, results are good, and implementation! Introducing case studies of Brodisk adoption.

We received an inquiry and a request for a loan through the trading company, and it was later adopted. After your inquiry, we reviewed the hopper diagram and the sample of the target material, and provided guidance on the applicable models, quantities, and layout (arranging 4 standard Brodisks). Based on the above information, we loaned the Brodisks for testing by the user, and the results were favorable, leading to implementation. The sample was a type of powder with quite poor conditions, so for air control, it is ideal to turn on the air for each of the 4 Brodisks one at a time with a time delay. However, in the test conducted this time, it worked well even with all 4 being turned ON/OFF simultaneously. 【Product Specifications】 ■ Brodisk: BD-15S-W x 4 ■ Controller: C-SV1 x 1 *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
Delivery to pharmaceutical manufacturer.

Delivery to pharmaceutical manufacturer.

A bridge occurred with the hopper! Introduction of a case where the Brody Disk Mini for pharmaceutical applications was implemented.

We would like to introduce a case regarding "delivery to pharmaceutical manufacturers" handled by Minagi Co., Ltd. We received an inquiry from a customer stating that a bridge occurs in a Ø300 hopper and they wanted to verify if it could be addressed with a Brody disk. They requested to borrow our equipment for this verification. After the customer disclosed various conditions (hopper drawings and details of the items), we proposed models, configurations, and quantities, with the intention of minimizing the number of units, leading to the implementation of four proposals. [Case Summary] ■ Issue - A bridge occurs in a Ø300 hopper, and they want to verify if it can be addressed with a Brody disk. ■ Result - After disclosing various conditions, we proposed models, configurations, and quantities, resulting in the implementation of four proposals. *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0564 Installation on food additive containers

0564 Installation on food additive containers

First, we installed it on one of the many containers! The bridge was resolved without any issues using a Brody disk.

The equipment was installed in a container for food additives (one of many). Although the interior was polished with a #400 buff to improve sliding, it was found that the bridge could not be eliminated, so it was first installed in one of the many containers. It was discovered that the bridge could be resolved without any issues using a blow disk, and subsequently, it has been installed in all of the many containers. [Container Overview] ■ Size: Approximately 1000×1000 ■ Discharge Section: Ø200 [Number of Blow Disks Installed] ■ Per Container: 4 units [Control] ■ Controlled by a C-SV4 controller with 4 built-in solenoid valves. Although there are many containers, since there is only one discharge station, one controller is sufficient. *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0570 Solving suction issues caused by resin chips/bridges

0570 Solving suction issues caused by resin chips/bridges

Installed and tested by the user! A case where this device solved the issue of being unable to perform suction transport.

This is an example of a solution provided by our equipment for a bridge formation in the hopper of crushed resin pellets, which prevents suction transport. The Brody Disk can be widely used to prevent clogging and bridging caused by materials such as powders, granules, pellets, and film crushings. 【Overview】 ■ Target Material - Pellets: Up to 8mm (often pointed) ■ Hopper - Size: 500×500 - Shape: 3 sides inclined, 1 side vertical - Discharge section: Suction from the horizontal bottom with Ø50 ■ Equipment Arrangement - A total of 3 units, one on each inclined surface (standard Brody Disk) ■ Introduction Flow - The user requests a loan of the equipment, installs the required quantity for testing - If results are satisfactory, the equipment, including the controller, is introduced *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録
0578 Measures for Hanging Storage of Incineration Ashes

0578 Measures for Hanging Storage of Incineration Ashes

Arranging 14 Brodisk BD-15S-B units! A case study targeting high-moisture incineration ash.

The measures for the shelf suspension of incineration ash have been adopted. We received contact from the customer stating, "The hopper's slope is 45° and is too gentle, causing bridging." As a countermeasure, they had already decided to modify the hopper (by adding steel plates to create a steep slope), but they also expressed a desire to add our equipment in line with this. Since it was mentioned that the incineration ash had a high moisture content, we provided a proposal for installation considering this. A total of 14 blow discs were arranged on the 2500 surface (2 surfaces). [Case Overview] ■ Hopper Size: Approximately 1500×2500 ■ Target Material: Incineration Ash (high moisture content) ■ Equipment Arrangement - Installed on the 2500 surface (2 surfaces) - 3 units on the lower level and 4 units on the upper level per surface / Total of 14 units arranged *For more details, please refer to the PDF document or feel free to contact us.

  • Vibration motor
  • Other contract services
  • Other machine elements

ブックマークに追加いたしました

ブックマーク一覧

ブックマークを削除いたしました

ブックマーク一覧

これ以上ブックマークできません

会員登録すると、ブックマークできる件数が増えて、ラベルをつけて整理することもできます

無料会員登録

Broad Discの関連カテゴリ

COPYRIGHT © 2001-2025 IPROS CORPORATION ALL RIGHTS RESERVED.