エルムテクノロジー Product Lineup

The ELM631FA is a synchronous buck-boost converter that incorporates four switch transistors. It can continuously boost and buck over a wide range of input and output voltages. With peak current mode and fixed off-time control, it enables smooth voltage control in all modes: boost, buck-boost, and buck. It employs a current detection method based on the DC resistance of the coil, allowing for high-efficiency control without current sensing resistors. An external phase compensation circuit enables stable control under a wide range of operating conditions. It includes built-in features such as a soft-start circuit, maximum switch current limit, input voltage drop detection, overvoltage output detection, overload-output short protection, and overheat protection. The rich built-in features facilitate power system configuration, reduce the need for external components, and allow for a smaller footprint. The ELM631FA uses a 28-pin QFN package measuring 5mm x 5mm.

• converter

The ELM615DA is a high-efficiency synchronous buck DC-DC converter that can accept input voltages from 4V to 36V and incorporates two switch transistors for high-side and low-side operation. It demonstrates excellent transient response to input and load variations due to its 180kHz COT control method. The use of slew rate control and a 3kHz 6% frequency modulation spectrum spreading technique reduces unwanted radiation. The output voltage range is from 0.8V to VIN, and it can provide output currents up to 5A. It includes a circuit that compensates for output voltage drop due to wiring resistance on the output side, which is effective for USB devices and can compensate for voltage drops at the load end. Additionally, it features independent dual-channel current monitoring capabilities, allowing for overcurrent protection for two separate loads.

• converter

The ELM624BA provides a power solution for electronic devices that use 1-cell, 2-cell, or 3-cell alkaline batteries, nickel-hydrogen batteries, or 1-cell lithium-ion or lithium-polymer batteries. The output current varies based on the input-to-output voltage ratio; for example, it can achieve 5V/100mA output with a 1.2V input. It can start at a low voltage of 0.7V under light load. It employs a high-efficiency synchronous rectification current mode control pulse width modulation method. The output voltage can be programmed using external resistor voltage division. During shutdown, it stops circuit operation to minimize current consumption. In shutdown mode, the ELM624BA directly connects the battery input to the output, allowing the input battery to be used directly as a backup or real-time clock power source. The ELM624BA is available in a compact 6-pin SOT-26 package.

• converter

The ELM77xxxxxC is a dual CMOS voltage detector for battery-operated devices. Unlike general voltage detectors, this IC incorporates two comparator circuits that simultaneously and independently monitor Vdetn2 (Vdd level) and Vdetn1 (Vdet level). This allows the output to remain in a detected state even when the Vdet level drops to 0V. The package is SOT-25, SC-75. We also have a wide range of standard power supply voltage devices available. Please check our website for more information. For more details on the ELM77 series, please refer to the catalog or feel free to contact us.

• Other semiconductors

The ELD6501A is a laser diode module that integrates a 650nm wavelength, 5mW rated output laser chip, a monitor diode, and an APC drive circuit into a TO-56 metal can package. Since it has all the APC circuits built-in, it can output APC-controlled laser light using only a laser light output setting resistor. The integration into a TO-56 package allows for miniaturization and weight reduction of laser application devices. With the built-in APC circuit, it enables shorter development times and improved reliability due to metal can sealing. Additionally, it can block external surges from the laser chip, enhancing electrostatic discharge resistance during assembly and transportation.

• diode

**Overview** The ELM185xB is a bipolar structure laser diode driver IC that incorporates an APC circuit consisting of a reference voltage source and an error amplifier. It stabilizes the laser output against changes in supply voltage and temperature using the reference voltage source within the IC. The driver output can drive laser currents of up to 400mA. Due to its compact package, it allows for implementation in a minimal area. As a protective feature, it includes a cutoff circuit for abnormal high temperatures and has the capability to limit the laser drive current in case of control loop failure. The current limit value can be set using an external resistor. It also has a built-in surge-absorbing Zener diode (Vz≈7V) between the power supply (VCC-GND) to prevent laser diode damage. It can drive multiple types of laser diode modules (LDM). Furthermore, it is possible to use the built-in constant current setting function for open-loop constant current driving, rather than driving through APC control, allowing it to be used as an open-loop constant current driver for laser diodes, high-brightness LEDs, and more. *For more details, please refer to the catalog or feel free to contact us.*

• diode
• Dedicated IC
• Other semiconductors

【Overview】 This IC incorporates an APC circuit that maintains a constant laser output and can control a forward current of up to 120mA for the LD. It includes a bandgap reference voltage circuit and an APC laser drive circuit, allowing the laser output to be set arbitrarily by an external resistor. Additionally, this IC is implemented in a compact SC-70-5 package, requiring few external components and enabling very small PCB footprints. Four types of ELM186C1A, ELM186C2A, ELM186C3A, and ELM186C4A are available, capable of driving all types of laser diode modules (LDM) with different polarities. Each type of LDM has one common pin, with four combinations available based on the selection of the anode or cathode on the LD side and the anode or cathode on the MD side. *For more details, please refer to the catalog or feel free to contact us.*

• diode
• Other semiconductors
• Dedicated IC

The single power MOSFET series is a high-current MOSFET with characteristics of low input capacitance, low voltage drive, and low ON resistance. The single N-channel ELM43400CB is a high-current MOSFET with the same characteristics of low input capacitance, low voltage drive, and low ON resistance. Some products are ESD resistant due to protective circuits. Please check our website for more information. *For more details on the 43400CB, please refer to the catalog or feel free to contact us.

• Transistor

The single power MOSFET series is a high-current MOSFET with characteristics of low input capacitance, low voltage drive, and low ON resistance. The single P-channel ELM43401CA is a high-current MOSFET with the same characteristics of low input capacitance, low voltage drive, and low ON resistance. Some products are ESD resistant due to protective circuits. Please check our website. *For more details on the 43401CA, please refer to the catalog or feel free to contact us.

• Transistor

**Overview** We offer the ELM7SH series as high-speed logic ICs. The ELM7SH series consists of single-gate CMOS high-speed logic ICs. The packages are compact SOT-25 and SC-70-5 (SOT-353), allowing for placement of as many as needed, significantly reducing the mounting area and wiring distance. Additionally, the input terminal protection circuit adopts a design without protection diodes on the power supply voltage side, allowing for the acceptance of signal inputs with voltages higher than the power supply voltage (input tolerant). *For more details, please visit our website or feel free to contact us.*

• Transistor

**Overview** The ELM6M003SA is a 5V 1.5A synchronous rectification buck DC/DC converter module that integrates a switching regulator IC, inductor, and output capacitor. The input voltage range is 2.5V to 6.0V, and the output voltage can be set within the range of 0.6V to the input voltage (maximum duty cycle of 100%). The constant on-time (COT) control method simplifies loop compensation and achieves high-speed load transient response characteristics. Additionally, the quiescent current is very low at 15μA (typ.), resulting in excellent light-load efficiency. Furthermore, the unique adaptive on-time control ensures that the switching frequency remains nearly constant across all load ranges. Protection features include current limiting per PWM cycle and hiccup mode, which protect the IC from overload or short-circuit conditions. The package is a compact and thin 7-pin LGA measuring 3mm x 3mm. *For more details, please refer to the catalog or feel free to contact us.*

• converter

The "ELM84 series" is a CMOS voltage regulator with a high output current of 1.2A and low dropout. It features a built-in current limiting protection circuit to restrict output current and a thermal shutdown circuit to prevent damage from overheating. The output voltage supports 1.2V, 1.8V, 3.3V, and 5.0V, and semi-custom ICs are also available in the range of 0.8 to 5.0V. 【Features】 ■ Overheat protection function ■ Current limiting function ■ Short-circuit protection function ■ Output voltage range: 0.8 to 5.0 V (in 0.1V increments) *For more details, please refer to the catalog. Feel free to contact us with any inquiries.

• Other electronic parts

The ELM73 series is a CMOS voltage detector IC with a delay function, and the delay time can be adjusted with an external capacitor. It operates with a very low supply current (Typ. 260nA). The ELM73xxxBxxA series features a manual reset function, allowing for manual resets at any time. There are two output styles: N-channel open-drain output and CMOS output. When the supply voltage Vdd drops below the detection voltage, the output level goes low. The detection voltages available as standard are 2.2V, 2.7V, 3.0V, and 4.0V, but they can be customized in the range of 1.4V to 5.0V in 0.1V increments. Since March 2019, a new pin configuration has been established for the SC-70-5 package, making it pin-compatible with NJU770x from NJ Corporation, thus enhancing usability.

• Dedicated IC

It is a low power consumption type with an output current of 150mA and a typical consumption current of 1μA. You can choose whether or not to include the chip enable function. The output voltage can be set in increments of 0.1V within the range of 1.5V to 5.0V. It supports thermal shutdown and current limiting protection circuit functions. It is a space-saving design that can use low ESR ceramic capacitors for input and output capacitors.

• Dedicated IC
• Other semiconductors