マイクロニクス List of Products and Services

Here is an example of on-site measurement of radiated emissions in a field without a shielded environment. This is an on-site measurement system for radiated emissions for pre-compliance testing. It is very convenient for measuring EUTs (Equipment Under Test) that are difficult to bring to the test site, such as large equipment. Since it is a combination of our products, it offers excellent cost performance, and being a handheld measurement device, it allows for easy measurements outdoors. It is also possible to identify the radiation source using a near-field probe. 【Measurement Process】 (1) Measure environmental noise when EUT is powered OFF (2) Measure noise when EUT is powered ON (3) Subtract (1) from (2) to extract only the noise from the EUT *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

The system can perform relative evaluations for debugging purposes during pre-assessments before formal testing or in the event of failure. It is a popular simple measurement tool because it allows for low-cost checks of noise components and enables subsequent system upgrades. It can simply measure the frequency bands emitted by the DUT. It is particularly effective for EMC noise countermeasures, compliance with radio laws, and confirming unwanted radiation. In formal tests using a shielded room, while it may not be possible to identify absolute values, it is possible to check whether unspecified frequencies are being emitted outside the specified limits by combining a spectrum analyzer with a simple loop antenna. 【System Configuration】 ■ EMI Spectrum Analyzer [MSA438E] ■ N to SMA Coaxial Cable 1.5m ■ Small Loop Antenna (one set of two sizes) *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

This is an introduction to a case where conducted EMI (noise terminal voltage) measurement was achieved easily and inexpensively using an EMI spectrum analyzer and LISN. The EMI spectrum analyzer "MSA438E" is equipped with the necessary functions for conducting EMI tests and is designed for EMI measurements. By using the dedicated EMI measurement software "MAS430," you can simply specify the standards you want to measure, such as CISPR11, 22, EN55011, 22, FCC Part 15, and VCCI, and the required parameters like bandwidth and threshold level will be automatically set. 【System Configuration】 ■ EMI Spectrum Analyzer [MSA438E] 　/ Lithium-ion Battery [MB400] ■ MSA438E Calibration Set ■ EMI PC Software [MAS430] / USB Cable [MI400] ■ LISN [MPW201B] ■ Noise Cut Transformer ■ Connection Cable N→BNC Cable [MC102+MA306] *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

This is an introduction to field maintenance of disaster prevention administrative wireless systems using handheld signal analyzers. Handheld signal and spectrum analyzers are suitable for inspecting and maintaining radios in the field, as well as for exploring interference and jamming waves in the system. They play a crucial role in the early detection of repairs and faults during system failures and in preventing issues before they occur. 【Solution】 ■ Handheld Signal Analyzers - MSA538: Frequency range 20kHz to 3.3GHz - MSA558: Frequency range 20kHz to 8.5GHz * There is also an MSA538TG with a built-in tracking generator. * For more details, please refer to the PDF document or feel free to contact us. 【System Configuration】 ■ Handheld Signal Analyzer [MSA538] (20kHz to 3.3GHz) ■ Handheld Signal Analyzer [MSA558] (20kHz to 8.5GHz) ■ Handheld Signal Analyzer [MSA438] (50kHz to 3.3GHz) * For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

We received an inquiry asking, "Can the MSA500 series measure LoRa signals?" and conducted actual measurements. "LoRa" is one of the LPWA (Low Power Wide Area) technologies that uses the 920MHz band, allowing direct communication over distances of up to 10 km, characterized by low power consumption. LoRa signals employ a special modulation method called chirp spread spectrum. As a result of our measurements, we were able to capture LoRa signals (LPWA using the 920MHz band) using the real-time mode of our "MSA500 series signal analyzer." 【System Configuration】 ■ Handheld Signal Analyzer (MSA538) ■ Sleeve Antenna for 920MHz Band (M401) *For more details, please refer to the PDF document or feel free to contact us. 【Product Introduction】 ■ Handheld Spectrum Analyzer MSA538 ■ Portable Antenna M401~407 *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

Our company can conduct a simple "radiated immunity test" at frequencies from 80MHz to 500MHz with a field strength of 30V/m for pre-evaluation before bringing the Equipment Under Test (EUT) to the EMC test site, as well as for evaluating the effectiveness of countermeasures. To perform the radiated immunity test at low frequencies of 80MHz to 500MHz with a strong electric field of 30V/m, we use a very confined space known as a shielded box, compared to an anechoic chamber, by placing a small loop antenna close to the EUT (within ~5cm). [Test Procedure] [Calibration] 1) Set up the electric field probe at the EUT installation position for calibration. 2) Adjust the level of the signal generator to achieve the desired electric field strength. 3) Determine the level of the signal generator. [Test] 1) Install the EUT and set it to the level determined during calibration. 2) Conduct tests to check if the EUT malfunctions. 3) Repeat the test while moving the antenna up, down, left, and right. *For more details, please refer to the PDF document or feel free to contact us.

• EMC Testing

We offer a cost-effective "Electromagnetic Wave Radiation Pattern Measurement System" that requires no installation and saves space. By using this measurement system, you can measure the electromagnetic wave radiation patterns of small wireless devices and antennas. The anechoic chamber is equipped with electromagnetic wave absorbers on all six sides. It blocks unwanted external electromagnetic waves and interference waves, suppressing reflections of electromagnetic waves emitted from the EUT inside, thus providing a stable measurement environment with a wide dynamic range. 【Anechoic Chamber Specifications (Base Model: MY5310S)】 ■ External Dimensions: Approximately 1345(W) × 1220(H) × 1080(D) mm * Excluding caster height and protrusions ■ Door Opening Dimensions: Opening dimensions approximately 510(W) × 910(H) mm ■ Weight: Approximately 300–460 kg * Depends on the electromagnetic wave absorbers ■ Turntable: φ220 mm, load capacity 10 kg * For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments

We would like to introduce a system that can receive GPS signals even inside buildings where GPS signals cannot reach. With the GPS signal retransmission system, it is possible to set up in-vehicle devices that use GPS signals, such as car navigation systems and dash cameras, indoors where GPS signals are unavailable. This retransmission system receives GPS signals with an outdoor receiving antenna, amplifies them, and then retransmits them through indoor transmitting antennas. It can radiate GPS signals from up to six transmitting antennas. 【Product Introduction】 ■ GPS Signal Retransmission System "MN1600" *For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic measuring instruments

We will introduce the differences in measurement results due to antenna variations and the selection methods. In pre-compliance testing for radiated EMI (emissions), it is important not only to have high-performance measuring instruments but also to select the appropriate receiving antennas in order to measure lower levels of noise. Small and medium-sized biconical antennas have inferior performance compared to biconical antennas, but they are smaller in size and highly portable. They are convenient for field measurements where portability is essential or when used close to the equipment under test (EUT) for noise exploration. Selecting the appropriate antenna based on the usage environment is crucial. 【Solutions】 ■ Automatic measurement software ■ Spectrum analyzers ■ Various antennas *For more details, please refer to the PDF materials or feel free to contact us.

• Time-frequency measurements

The "MR2150" is a pre-compliance system for conductive EMI testing. By using this system for debugging evaluation before the official EMC tests conducted at certified EMC sites, significant reductions in development costs can be achieved. Since the spectrum/signal analyzer, LISN, and PC software are all developed in-house, the overall usability and operational stability of the system have been thoroughly verified. Additionally, each component is reasonably priced, providing a cost-effective testing environment. 【Features】 ■ Provides a reasonable and cost-effective testing environment ■ Handheld spectrum/signal analyzers that can be selected based on budget and performance/features ■ Efficiency improvements in EMI testing through rich software functionalities ■ Excellent portability of the LISN *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

The "MSA500 Series" is a handheld signal analyzer that combines real-time and sweeping methods. By incorporating both real-time processing using Fast Fourier Transform (FFT) and traditional sweeping methods, it allows for the advantages of both approaches to be utilized. 【Features】 ■ Real-time plus sweeping method ■ Comprehensive analysis functions ■ Time domain analysis that expands the capabilities of the analyzer ■ Does not miss unwanted spectra ■ Powerful triggering functions ■ Captures modulation signals from most wireless communications ■ Built-in large capacity memory of 16K frames and high-speed USB transfer ■ Average noise level of -162dBm/Hz ■ Compact and lightweight at 1.8kg ■ 4 hours of battery operation ■ Data storage on USB memory *For more details, please refer to the PDF document or feel free to contact us.

• Time-frequency measurements

The "MY2520" is a production line type of radio wave shielding box that is appropriately sized for A4 equivalent products, accommodating a wide range of applications while reducing equipment costs. Thanks to the one-touch locking mechanism, the shielding effect is maintained despite the ease of opening and closing, which also reduces the burden on operators. It is integrated with a base, allowing for anti-tipping measures that can be fixed to work desks or shelves. It can accommodate various customizations based on actual operating conditions (additional costs apply). Options include surface processing for IF modules, IFM1 to IFM6, and radio wave absorbers. 【Features】 ■ Compact radio wave shielding box for production lines of radios, terminals, modules, etc. ■ Appropriately sized for A4 equivalent products ■ One-touch locking mechanism shortens tact time ■ Improves reproducibility of various communication tests ■ Accommodates a wide range of applications while reducing equipment costs *For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic measuring instruments

The "MY5550" is a locally assembled radio wave absorption partition that realizes an ideal space for confirming the directivity and gain of antennas mounted on 5th generation mobile communications and millimeter-wave radars, simulating various communication tests, and applying and developing in-vehicle sensing technologies, all at low cost and short delivery times. By assembling six-sided partitions to create a space and fixing radio wave absorbers to the inner walls, it converts radio waves into heat, suppressing reflection and transmission of radio waves. A dedicated steel plate is laid on the floor to match the size of the partition, distributing the load. By reducing the load applied to a single point, it accommodates more locations during measurements. Since it is equipment not subject to construction industry and fire safety laws, the procedures for installation are easy. 【Features】 - Realizes an ideal space for radio waves at low cost and short delivery times - Locally assembled, no large-scale construction required - Short construction period (basic installation work takes 1 day + radio wave absorber installation takes 1 day) - Suitable for confirming the directivity and gain of antennas mounted on 5th generation mobile communications and millimeter-wave radars, simulating various communication tests, and applying and developing in-vehicle sensing technologies *For more details, please refer to the PDF document or feel free to contact us.

• Other laboratory equipment and containers

The "Taurus series" is a radio wave shielded box that allows for the easy creation of evaluation environments for wireless testing of information communication devices such as WLAN, mobile phones, WiMAX, and RFID.

• Other laboratory equipment and containers

New series for "Taurus." Offered at an even lower price. Low price, lightweight, short delivery time! Three models that meet diverse needs. The "Taurus-N series" is a shield box that allows for easy creation of evaluation environments for wireless devices such as mobile phones and wireless LAN. These three models achieve a lower price by eliminating the radio wave absorbers found in the existing "Taurus series." With a removable and interchangeable I/F module, they support a wide range of interfaces including USB, LAN, and AC power. Shielding performance is over 50dB for all models. [Lineup] ■ Ultra-lightweight and compact type at the lowest price Internal dimensions: 375×375×160mm, Weight: 1.9kg Standard price: 159,000 yen ■ Excellent workability with a front opening Internal dimensions: 515×515×515mm, Weight: 12.3kg Standard price: 348,000 yen ■ Large size and low price type Internal dimensions: 1115×615×615mm, Weight: 42kg Standard price: 770,000 yen *Please refer to the catalog for detailed specifications.

• Other laboratory equipment and containers

MY1515 offers high quality and reliability provided by a measurement instrument manufacturer. It excels in cost performance and has a short delivery time! It is a radio shield box covered with a radio wave absorber inside. It suppresses the rise in temperature inside the box, creating an ideal testing environment for long hours of continuous operation. For more details, please download the catalog or contact us. 【Features】 - High quality and reliability provided by a measurement instrument manufacturer - Excellent cost performance and short delivery time - Radio shield box covered with a radio wave absorber inside - Suppresses temperature rise inside the box, achieving an ideal testing environment for long hours of continuous operation 【Specifications】 - External dimensions: 465 (W) × 465 (D) × 214 (H) mm (excluding handles, etc.) - Internal dimensions: 400 (W) × 400 (D) × 150 (H) mm - Weight: Approximately 10 kg (excluding I/F module) - Shielding performance: 70 dB (typical value at 2.4 GHz) - Absorption performance: 20 dB or more (MYA-75: above 2.4 GHz) - Fan: 0.56 cubic m/min (maximum airflow) - Connectors: 8 SMA (8 on the back) - I/F module: 1 unit (1 on the back) ● For more details, please download the catalog or contact us.

• EMC Testing

The MY1525 has a shielding performance of 90dB (typical value). It supports various applications in a wide bandwidth of 800MHz to 6GHz. The design features a fully opening front door (left-opening) for smooth DUT replacement and other tasks. It comes standard with an exhaust fan and air intake. For more details, please download the catalog or contact us. 【Features】 ○ Shielding performance of 90dB (typical value) ○ Supports various applications in a wide bandwidth of 800MHz to 6GHz ○ The design with a fully opening front door (left-opening) allows for smooth DUT replacement ○ Standard equipped with an exhaust fan and air intake 【Specifications】 ○ External dimensions: 460 (W) × 575 (D) × 570 (H) mm (excluding handles, etc.) ○ Internal dimensions: 340 (W) × 400 (D) × 340 (H) mm ○ Weight: Approximately 17 kg (excluding I/F module) ○ Shielding performance: 90dB (typical value at 2.4GHz) ○ Absorption performance: 20dB or more (MYA-77: above 1.2GHz) ○ Fan: 0.56 cubic m/min (maximum airflow) ○ Connectors: 2 SMA (rear) and 1 dedicated I/F module (1 rear) ● For more details, please download the catalog or contact us.

• EMC Testing

The MY1520SW comes standard with a large shielded window. The internal state of the RF shielded box can be visually monitored, allowing for constant observation of the EUT's state changes from the outside. It accommodates a wide range of testing environments, including checking for display malfunctions due to the effects of radiated noise and operation verification during high-speed data communication. For more details, please download the catalog or contact us. 【Main Features】 - Standard large shielded window - Visual monitoring of the internal state of the RF shielded box, enabling constant observation of EUT state changes from the outside - Accommodates a wide range of testing environments, including display malfunctions due to radiated noise and operation verification during high-speed data communication 【Other Features】 - Shielding performance of 70 dB (typical value at 2.4 GHz) - A cover for light shielding is provided, ensuring thoroughness during illuminance and brightness measurements - Supports a variety of interfaces ● For more details, please download the catalog or contact us.

• EMC Testing

The most versatile medium size that accommodates multiple purposes! Electromagnetic Shielding Box (Shield Box) MY1520SW Devices and components that require an electromagnetic shielding box for testing, measurement, and inspection span a wide range of fields. The Taurus series provides the optimal environment to achieve this purpose. ■□■Features■□■ ■ The internal state of the electromagnetic shielding box can be visually monitored, allowing for constant observation of the EUT's condition changes. ■ Equipped with a large shielding window as standard. ■ Shielding performance ensures 70dB (typical value at 2.4GHz). ■ A cover for light shielding is provided, ensuring thoroughness during illuminance and brightness measurements. ■ For other functions and details, please download the catalog or contact us.

• Testing Equipment and Devices

Unlike conventional mechanical attenuators, this is optimal for linear wireless evaluation (such as distance attenuation and handover) without chattering or spikes during attenuator switching. Frequency correction is divided into 16 segments to achieve a flat frequency response within the band.

• Other network tools

The MAT810 adopts an electronic switching method, enabling high-speed switching of 2μs without spikes. It is ideal for handover tests, dynamic operation tests, communication simulations for low-power wireless communication devices such as WLAN, ZigBee, and weak wireless, as well as for receiving sensitivity and fault countermeasures. The MAT810 adopts an electronic switching method, enabling high-speed switching of 2μs without spikes. The frequency range is from 300MHz to 6.6GHz, with a maximum attenuation of 60dB, and the attenuation setting can be adjusted in steps of 0.05dB. It has a built-in program memory of 128k words, and arbitrary waveforms can be easily created using the included attenuation program creation software.

• Other network tools

The MAT850 is easy to operate. It is a compact and lightweight step attenuator that allows you to switch the attenuation of microwave electrical signals while confirming it with an LED display. You can manually adjust the current attenuation in 0.1 dB increments. It is ideal for evaluating call quality in mobile phones, WiMAX, PHS, etc., as well as wireless LANs and communication devices. For more details, please download the catalog or contact us. 【Main Features】 - Compact and easy to operate - Attenuation of microwave electrical signals can be switched while confirming with an LED display - Manual adjustment in 0.1 dB increments while checking the current attenuation 【Other Features】 - Wide frequency range from 300 MHz to 6.1 GHz - Minimum step of 0.1 dB for attenuation settings, maximum attenuation of 60.0 dB - Equipped with a spike noise removal circuit during attenuation switching - Easy-to-read LED display ● For more details, please download the catalog or contact us.

• Other electronic parts

This is an announcement from Micronics Corporation regarding the "EMI Measurement Spectrum Analyzer (Specan) MSA438E."

• Time-frequency measurements

This is a spectrum analyzer equipped with a TG, enabling the measurement and evaluation of the amplitude frequency characteristics of filters, amplifiers, and other electronic devices or circuits. 【Features】 ○ Compact and lightweight at 1.8kg, convenient for measurements on business trips or outdoors ○ Large color LCD display ○ Optional lithium-ion battery allows for up to 4 hours of use ○ Compatible with USB memory. Can be used as external memory, with the screen saving spectra waveforms in BMP format and setting parameters in CSV format ○ USB communication is possible. With the adoption of a USB interface, transfer speeds can reach up to 12Mbps ○ Accurate frequency measurement using a PLL synthesizer ○ Low average noise level of -127dBm at 1GHz, ensuring a wide dynamic range ○ Amplitude axis display of 100dB/10div, allowing observation of signals over a wide dynamic range ○ Easy operation with AUTO mode ● For other functions and details, please download the catalog.

• Other measurement, recording and measuring instruments

The MY5310S is a two-part assembly type of the large electromagnetic shielding box "MY5310." It maintains shielding performance while allowing for division and assembly. It is ideal for transportation via passenger elevators and installation in narrow spaces such as office buildings. For more details, please download the catalog or contact us. 【Main Features】 - Two-part assembly type of the large electromagnetic shielding box "MY5310" - Maintains shielding performance while allowing for division and assembly - Suitable for transportation via passenger elevators and installation in narrow spaces such as office buildings 【Other Features】 - Division for transportation makes it easy to install in office buildings - Can be transported using a standard 11-person elevator common in office buildings - Division and assembly can be done without specialized tools or expertise - Flexible response for relocation of the equipment ● For more details, please download the catalog or contact us.

• EMC Testing

MY5310/MY5410 is a radio wave dark box optimized for large and small EMI tests using ferrite-based radio wave absorbers. An ultra-compact, wideband antenna (30MHz to 3GHz) developed in-house is available as an option. By upgrading to the MR2300 system, EMI testing from 30MHz to 3GHz becomes possible. For more details, please download the catalog or contact us. 【Main Features】 - Uses ferrite-based radio wave absorbers - Suitable for large and small EMI tests - Offers an ultra-compact, wideband antenna (30MHz to 3GHz) as an option - Upgrading to the MR2300 system enables EMI testing from 30MHz to 3GHz 【Other Features】 - MY5310 → For large-sized EMI tests → Standard equipped with a turntable with a diameter of 220mm and a load capacity of 10kg for small EUTs - MY5410 → For extra-large-sized EMI tests → Standard equipped with a turntable with a diameter of 756mm and a load capacity of 100kg for large EUTs ● For more details, please download the catalog or contact us.

• EMC Testing

A structure with a large opening and one-touch lock, ideal for mass production lines. The latest model of a shielded box (electromagnetic shield box) with high shielding performance. By adding an optional connector box, it can utilize multiple interfaces (including AC power, USB, LAN, and D-sub 9-pin), and it is equipped with a noise filter to reduce external interference.

• Other laboratory equipment and containers

It has a three-layer structure consisting of a radio wave absorber, copper plate, and aluminum plate, covering a frequency range from low frequencies up to 18 GHz. It is a simple type of radio wave dark box that can be used on a tabletop. Additionally, an acrylic platform for placing the DUT is installed, and it is designed for easy attachment of an optional receiving antenna.

• Other laboratory equipment and containers

The ME8662 lineup includes two models: the shielded-only "ME8662N" and the radio wave dark box compatible "ME8662E." The ME8662N can block external noise to perform measurements on high-impedance circuits and components. The ME8662E is ideal for evaluating transmission and reception in coaxial cable connections for small wireless communication devices (mobile phones, wireless LANs, ETC onboard units). For more details, please download the catalog or contact us.

• EMC Testing

The ME8668 is a mass production model equipped with an automatic transport system suitable for production lines. It is ideal for technical standard compliance tests, reception sensitivity tests, EMC tests, and more. For more details, please download the catalog or contact us. 【Features】 ○ Equipped with an automatic transport system suitable for production lines ○ Model for mass production sites ○ Suitable for technical standard compliance tests, reception sensitivity tests, EMC tests, etc. 【Specifications】 ○ External dimensions: 922 (W) × 794 (H) × 731 (D) mm (excluding protrusions) ○ Automatic transport system → Dimensions: 634 (W) × 436 (H) × 260 (D) mm → Transportable item: 150 (W) × 150 (H) × 150 (D) mm ○ Internal dimensions → 801 (W) × 610 (H) × 610 (D) mm ○ Weight: Approximately 94 kg (including the automatic transport system) ○ Connectors: 2 SMA ○ Structure: Dual structure of radio wave absorber and stainless steel ○ Shielding performance: 60 dB or more @ 2.4 GHz ○ Reflection loss → 20 dB or more @ 1.2 GHz～ ● For more details, please download the catalog or contact us.

• EMC Testing

The MY5305 is a compact radio wave anechoic chamber designed for low-frequency measurements and EMC testing. The turntable is an optional feature. The wave absorber is made of ferrite, making it compact and space-saving. It is suitable for a wide range of applications, including wireless LAN and one-segment broadcasting. It is ideal for technical standard conformity tests, reception sensitivity tests, and EMC tests. For more details, please download the catalog or contact us.

• EMC Testing

ME8669 is a radio wave dark box compatible with low frequency bands (50-800 MHz) using ferrite-based radio wave absorbers. It is ideal for technical standard compliance tests, reception sensitivity tests, EMC tests, etc. For more details, please download the catalog or contact us. 【Features】 ○ Uses ferrite-based radio wave absorbers ○ Compatible with low frequency bands (50-800 MHz) ○ Suitable for technical standard compliance tests, reception sensitivity tests, EMC tests, etc. 【Specifications】 ○ External dimensions: 915 (W) × 650 (H) × 585 (D) mm (excluding protrusions) ○ Internal dimensions: 810 (W) × 506 (H) × 506 (D) mm ○ Weight: Approximately 165 kg ○ Structure: Double structure of ferrite-based radio wave absorber and stainless steel (hairline finish) ○ Shielding performance: 50 dB or more @ 300 MHz ○ Reflection loss: 20 dB or more @ 50 MHz - 800 MHz ○ Connectors: 2 SMA ○ I/F: D-sub 25 pin ● For more details, please download the catalog or contact us.

• EMC Testing

The MR2300 is an integrated system that combines our spectrum analyzer technology, anechoic chamber technology, and antenna technology. Features of the EMI Total Test System MR2300: ■ EMI total test system that requires no additional equipment A complete test system that includes not only antennas, EMI spectrum analyzers, LISN, and EMI PC software, but also an anechoic chamber. ■ In-house developed compact, wideband antenna A wideband antenna developed in-house that covers 30MHz to 1GHz. ■ Four types of anechoic chambers, large and small. ■ Simply read the measurement results directly from the PC screen. ■ Compliance with standard specifications Complies with CISPR11, CISPR22, EN55011, EN55022, VCCI (class A/B), and FCC part 15. Free demonstrations are available for those interested. For more details, please refer to the catalog.

• Other measurement, recording and measuring instruments

This is an EMS (Radiated Immunity) test device that evaluates whether the EUT (Equipment Under Test) malfunctions due to surrounding electromagnetic waves.

• EMC Testing

This system measures the electric field strength distribution of ETC/ITS spots in a short time using operational waves or CW waves, and creates electric field strength graphs and maps. Measurements can be conducted using a trolley or in-vehicle. - Measurements can be conducted using a trolley or in-vehicle, and the price of the ETC measurement system (with 9 antennas) is 2.95 million yen, which is affordable. - As an option, the electric field strength measurement function for ITS spots can be added (500,000 yen). - When measuring multiple roadside units on the main line, applying the automatic measurement mode allows for automatic measurements to be conducted while driving, according to the pre-registered measurement section locations and conditions.

• Other measurement, recording and measuring instruments

The DSRC communication unit has four models in its lineup. Broadly, they can be classified into WCN reading and electric field strength measurement. It also features data save/load and USB communication capabilities. The models include "ME9115A," which reads the WCN of the onboard unit and displays a 12-digit ID number; "ME9115AC," which measures the electric field strength between roadside units and onboard units; "ME9115A+C," a combination of ME9115A and ME9115C; and "ME9115ACN," which measures the electric field strength from moving vehicles to roadside units and can also measure the electric field strength of the onboard unit. For more details, please contact us or refer to the catalog.

• Testing Equipment and Devices

The DSRC in-vehicle device tester ME9100 is a tester that checks whether the in-vehicle device installed in a vehicle is communicating properly at the wireless level. It is an essential tool for automotive dealers, car accessory stores, or automotive maintenance companies that perform installation work, ensuring they provide customers with reliably functioning equipment. The ME9100 sends FCMC and checks whether ACTC and WCNC are correctly returned from the in-vehicle device. The power will automatically turn off after about 6 seconds from the start of the test (approximately 8 seconds for the DSRC in-vehicle device), extending battery life. It can conduct roughly 500 tests. For more details, please contact us or refer to the catalog.

• Testing Equipment and Devices

This is an announcement from Micronics Corporation regarding the "Comprehensive Catalog of Wireless Evaluation Equipment." Micronics provides measurement instruments and high-frequency related equipment to the world. ■□■Contents■□■ ■Spectrum Analyzers / Signal Analyzers ■EMC Test Systems ■Anechoic Chambers / Shielded Boxes ■ETC / DSRC Test Systems ■Variable Attenuators ■Signal Generators ■Test Accessories You can view the catalog by clicking the download button. For further details, please contact us through the document request.

• Testing Equipment and Devices

This is a notice from Micronics Corporation regarding the "Wi-Fi Evaluation Solution (Application Materials)." A system for conducting various characteristic evaluation tests for Wi-Fi (2.4GHz and 5GHz) products. ■□■ [Solution ■□■ ■ Handover characteristic evaluation ■ Fallback characteristic evaluation ■ Reception characteristic evaluation ■ For more details, please download the catalog or contact us.

• Testing Equipment and Devices

This is an announcement from Micronics Corporation regarding the "WiMAX Evaluation Solution (Application Materials)." A system for conducting various characteristic evaluation tests for WiMAX (2.5GHz band) products. ■□■Solution■□■ ■Handover characteristic evaluation ■Fallback characteristic evaluation ■Reception characteristic evaluation ■For more details, please download the catalog or contact us.

• Testing Equipment and Devices

Used for checking and maintaining retransmission signals and terminal-side reception levels, as well as measuring upstream signal interference noise on the internet, etc.

• Other measurement, recording and measuring instruments

This is a notice from Micronics Corporation regarding the "Wireless Terminal Evaluation Solution (Application Materials)." By creating an environment that minimizes unnecessary radio waves around development and production sites, this solution enables the evaluation of wireless systems for wireless terminals. ■□■ Solution ■□■ ■ Protocol (Layer 1-3) Testing via Air Connection - An environment is set up for bidirectional connection using a wireless simulator/SG and terminals installed inside a radio anechoic chamber, with transmitting and receiving antennas mounted within the chamber. - Each protocol (Layer 1-3) test is conducted using the wireless simulator. ■ Transmission Characteristics Testing of Wireless Communication Devices via Air Connection - Radio waves emitted from terminals placed on a turntable are received by a receiving antenna installed at the opposite position and output outside the radio anechoic chamber. - By connecting a spectrum analyzer or power meter to the input/output terminals, evaluations of various test items for the transmission characteristics of the wireless device can be conducted. ■ For more details, please download the catalog or contact us.

• Testing Equipment and Devices

By isolating wireless terminals and modules from unnecessary radio waves in the surrounding area and creating a radio wave anechoic environment, it becomes possible to evaluate the wireless systems of the evaluation terminals.

• Testing Equipment and Devices

By creating an environment that minimizes unnecessary radio waves around the development and production sites, it becomes possible to evaluate the wireless systems of wireless LAN devices. Evaluation of wireless LAN devices 【4×4 MIMO - Multiple Input Multiple Output】 By creating an environment that minimizes unnecessary radio waves around the development and production sites, it becomes possible to evaluate the wireless systems of wireless LAN devices. ■□■Features■□■ ■Radio Shielding Box MY5220 - A radio shielding box with high shielding performance. Ideal structure for manual work with a large opening. - Shielding performance of over 70dB @ 2.4GHz, 5GHz - Reflection loss of over 20dB @ 2.4GHz ■Programmable Attenuator MAT800/D - Ideal for handover tests and dynamic tests of wireless communication devices - No instantaneous switching spikes occur, preventing communication errors - Frequency range of 1.95 to 5.85GHz - VSWR 1.6≧ @ 2.6 to 5.2GHz / 2.1≧ @ 1.95 to 5.85GHz - Maximum attenuation of 80dB - Maximum input of 100mW ■For other functions and details, please download the catalog or contact us.

• Testing Equipment and Devices

By isolating the wireless LAN terminal from unnecessary surrounding radio waves and creating a radio anechoic environment, it becomes possible to evaluate the wireless system of the terminal. Evaluation of the wireless system of the wireless LAN terminal By isolating the wireless LAN terminal from unnecessary surrounding radio waves and creating a radio anechoic environment, it becomes possible to evaluate the wireless system of the terminal. ■□■Solution■□■ ■Transmission characteristic testing of wireless LAN terminals via air connection - The radio waves emitted from the W-LAN module installed on a turntable are received by a receiving antenna mounted at the opposite position and output outside the radio anechoic chamber. - By connecting measurement instruments such as a spectrum analyzer, the evaluation of each test item for the terminal's transmission characteristics can be conducted. ■Reception characteristic testing of wireless LAN terminals via air connection - Signals from the terminal are transmitted from the transmitting antenna through a programmable attenuator, and the baseband signal extracted from the W-LAN module is measured. - By connecting measurement instruments such as a BER (Bit Error Rate) meter, spectrum analyzer, or power meter, measurements of reception sensitivity and reception level can be conducted. ■For other functions and details, please download the catalog or contact us.

• Testing Equipment and Devices