グローバル電子 List of Products and Services

The "WF50FSYFGDHGV" is a TFT display that comes with a control board supporting the HDMI signal interface (DVI only) for the Raspberry Pi system. The board features a 40-pin GPIO connector, designed for easy use with the Raspberry Pi. The control board has four mounting holes, allowing for easy implementation into your equipment and products. 【Features】 ■ Module size: 120.7×75.8×23.2mm ■ LCD type: TFT, normally black, transmissive ■ Backlight: LED, normally white ■ Panel surface treatment: Glossy ■ Contrast ratio: 1000:1 * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• LCD display
• Touch Panel
• LED Module

The "MFR070KC-IX" is a horizontal TFT LCD module with a 7.0-inch capacitive touch panel. It features a wide viewing angle of 85 degrees left/right/up/down (Typ.), high brightness of 750 cd/m² (Typ.), and a backlight lifespan of 20,000 hours (Min.). It can be utilized in measuring instruments, remote control panels, printers, and more. 【Features】 ■ Viewing Angle: 85/85/85/85 IPS ■ LCD Type: Normally Black, Transmissive ■ Backlight Type: LED, Normally Black ■ Resolution: 1024×RGB×600 ■ Storage Temperature: -30℃ to 80℃ ■ Operating Temperature: -20℃ to 70℃ * An English version of the catalog is available for download. * For more details, please refer to the PDF document or feel free to contact us.

• LCD display
• Touch Panel
• LED Module

As the market for the single-pair Ethernet standard IEEE802.3cg, which is attracting attention for its miniaturization and reduced wiring as an IoT Ethernet solution, progresses, we would like to introduce LAN transformers suitable for single-pair Ethernet transmission circuits from Bones, various common mode chokes for signal noise countermeasures, TVS diode arrays for electrostatic discharge protection, and differential choke coils for power lines when used as PoE. You can watch the archived video of the "Next Generation Communication Standard Single Pair Ethernet (SPE) Free On-Demand Seminar" hosted by Global Electronics at the URL below.

• diode
• transformer

The "PB type" is a standard small and lightweight heat sink suitable for mounting on a circuit board. It has a well-balanced fin spacing and height, providing adequate heat dissipation performance for natural air cooling, making it suitable for installation on low-power CPUs under 10W. Designed for TO-220 and TO-3P type devices, it is equipped with 4.5mm pins that can be soldered to the circuit board. It can also be applied without the pins, installed parallel to the circuit board. We also offer specifications proposals using simple calculations and simulation software. 【Features】 ■ Thin and lightweight ■ Product length: 25mm (with exceptions such as 30mm depending on the model) ■ Surface treatment: Black anodized aluminum (cut surfaces and taps are not anodized) ■ Capable of proposing suitable specifications along with thermal design and custom processing *For more details, please refer to the materials. Feel free to contact us with any inquiries.

• Other electronic parts

The "M8/M12" is a connector that can be installed on-site to achieve reliable communication. The "M8 connector" is equipped with waterproof 3-pin screws and is particularly used in industrial sensors. It is delivered pre-assembled and maintains its waterproof properties even when submerged in water. The "M12 connector," on the other hand, is a round connector with a 12mm fixed screw thread, primarily used for actuators, sensors, industrial Ethernet, and Fieldbus in factory automation. 【Features】 ■ Protection ratings of IP67 and IP68 ■ X-coded connectors to meet bandwidth needs of up to 10Gb/s ■ Available in codes A, B, D, X, S, and T ■ Connectors with silver-plated terminals for excellent conductivity *You can download the English version of the catalog. *For more details, please refer to the PDF materials or feel free to contact us.

• Sensors
• Circular Connectors
• Other Connectors

"XCede HD" is a high-density, high-speed backplane connector system that achieves 16Gbps transmission. It offers various options required for backplane systems, such as power and guides, providing flexibility and expandability through excellent combinations. Compared to conventional backplanes, it contributes to space-saving on the circuit board with its high density. 【Features】 ■ Basic configurations of 3, 4, and 6 pairs ■ Prepared with 4, 6, and 8 rows at a 1.8mm pitch ■ Capable of configuring 84 pairs of differential signals within 1 inch ■ Options available for power, guide posts, direction keys, and side walls ■ Includes the BSP series as custom modules (right angle) * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic parts

The "MSS/MOS series" is a ferrite drum core inductor with a wide range of inductance values (0.8μH to 10mH) and size variations (5 to 18mm square). It features an industry-standard footprint, high current capacity, and low DCR, resulting in minimal heat generation, making it suitable for various applications such as smoothing circuits and filters. 【Features】 ■ Ferrite drum core inductor ■ Size variations: 5 to 18mm square ■ Inductance values: 0.8μH to 10mH ■ Current capacity: up to 36A ■ Low DCR * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Inductor Coil

The "6610-5 Series" is an IDC outlet that can be equipped with a light pipe to display the status of application operations and other functions. Thanks to the crimp terminals, cable stripping and soldering are unnecessary. It also supports V-Lock, P-Lock, and TwyLock cable retention mechanisms to prevent unintended disconnection. It is well-suited for applications that require multiple power outlets, such as smart PDUs specialized in power consumption management and uninterruptible power supplies (UPS). 【Features】 ■ Connector shape: F (compliant with IEC 60320-3) ■ Rated current - IEC: 10A/250VAC; 50Hz - UL/CSA: 15A/250VAC; 60Hz * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• Other power sources
• Other electronic parts

The "MISO400-F&MISO420-F" is a module that incorporates a 4-channel transformer-isolated isolation amplifier in a compact and low-profile package. It also includes an isolated DC/DC converter to supply isolated power to both the primary and secondary sides. This enables the miniaturization of multi-channel analog signal isolation systems. 【Features】 ■ Compact 45×35mm, low-profile 12mm package ■ Input/output signal voltage range: ±10V (when power supply is +15V) ■ Gain: ×1 to ×100 ■ Isolation between input and output: AC1,000V (min) ■ Isolation between channels: AC500V (min) ■ Frequency characteristics: DC to 5kHz (typ) *For more details, please refer to the PDF document or feel free to contact us.

• Other power sources
• Other electronic parts

The "WF28KTLAJDNT0" is a 2.8-inch SPI TFT-LCD module with a resistive touch screen (RTP) in portrait mode. The resolution is 240×320 pixels. The panel surface treatment is glossy, with a viewing angle of 6 o'clock and grayscale inversion direction at 12 o'clock. Additionally, it has a contrast ratio of 500:1 and a brightness of 350 nits (Typ.), and a version without a touch panel is also available. 【Features】 ■ Module size: 50.0×69.2×3.48mm ■ LCD type: TFT, normally white, transmissive ■ Backlight: LED, normally white ■ Resolution: 240×RGB×320 pixels ■ Storage temperature: -30℃ to 80℃ ■ Operating temperature: -20℃ to 70℃ * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• LCD display

The "WF24MTLAJDNT0" is a 2.4-inch SPI TFT-LCD module with a portrait mode, equipped with a resistive touch screen (RTP). The resolution is 240x320 pixels. The surface treatment of the panel is anti-glare, with a viewing angle of 6 o'clock and grayscale inversion at 12 o'clock. Additionally, the contrast ratio is 500:1, and the brightness is 350 nits (Typ.), with a version available without a touch panel. 【Features】 ■ Module size: 42.72×60.26×3.43mm ■ LCD type: TFT, normally white, transmissive ■ Backlight: LED, normally white ■ Resolution: 240×RGB×320 pixels ■ Storage temperature: -30℃ to 80℃ ■ Operating temperature: -20℃ to 70℃ * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• LCD display

The "WEO012864Z series" is a 0.96-inch COG type OLED display equipped with a control knob. The resolution is 128x64 dots. It has a built-in SSD1306 IC, and the interface supports 4-wire SPI and I2C. The supply voltage ranges from a minimum of 1.65V to a maximum of 3.3V, with a 1/64 duty cycle. 【Features】 ■ Built-in encoder allows operation beyond touch panel ■ Display colors: three colors - white, yellow, and blue ■ Supply voltage: 1.65 to 3.3V, duty cycle is 1/64 ■ Supports 4-wire SPI and I2C interfaces ■ Storage temperature: -30℃ to 80℃ ■ Operating temperature: -20℃ to 70℃ * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• LCD display

The "USB7206C" is a low-power USB 3.2 Gen 2 hub controller that can be configured by OEMs. It is fully compliant with the "Universal Serial Bus Revision 3.2 Specification" and the "USB 2.0 Link Power Management Addendum." It features six downstream ports and advanced capabilities for embedded USB applications. 【Features】 ■ USB 3.2 Gen 2 compliant with operation at 10Gbps/5Gbps/480Mbps/12Mbps/1.5Mbps ■ Supports common USB battery charging specifications on all ports ■ Built-in microcontroller ■ 96KB RAM, 256KB ROM * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Routers, Switches, and Hubs

RRC Power Solutions' lithium-ion batteries are designed with a focus on safety and comply with safety certification standards from around the world. Additionally, as the manufacturer has a policy of not discontinuing any model, it is possible to implement these batteries with peace of mind while keeping initial costs low. By using SMBus communication to read the battery's status and information, such as operating time, temperature data, and electrical specifications, more efficient management can be achieved. 【Features】 ■ Complies with various safety certification standards such as IEC62133, PSE, and UL ■ High energy density ■ Equipped with a gas gauge (remaining capacity indicator) 【Applications】 Medical devices, measuring instruments, inspection equipment, wearable devices, wireless devices, etc. *For more details, please refer to the materials. Feel free to contact us with any inquiries.

• Secondary Cells/Batteries

We would like to introduce the Bourns product "PWR263S-DN9" that we handle. This product is a resistor with a maximum allowable power of up to 45W continuous output rating, featuring high reliability against thermal shock and durability. It is designed to withstand reflow soldering peak temperatures of 260°C. It can be used in a wide range of applications, including current measurement circuits, snubber circuits, and bleeder discharge circuits. 【Features】 ■ Compact surface mount TO263 (D^2PAK) ■ Insulated backplate ■ Low inductance ■ Maximum operating temperature of 175°C ■ Automotive compliant (AEC-Q200) planned ■ RoHS compliant product * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Resistors

We would like to introduce the 'CSS Series' manufactured by Bourns. It consists of four models: three sizes of 2-terminal products and one size of 4-terminal products. The resistive material is processed by electron beam welding onto a copper base, and it is RoHS compliant. Additionally, the operating temperature range is -55 to 170°C, and the resistance value tolerance can be selected from ±1% or ±5%. 【Features】 ■ High power handling up to 12W ■ Ultra-long-term stability ■ Low resistance, low TCR ■ Low thermal electromotive force ■ RoHS compliant products * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Resistors

The input isolation module "MISO400-F" and the output isolation module "MISO420-F" are compact, low-profile packages that incorporate a 4-channel transformer-isolated isolation amplifier. Each side, primary and secondary, contains an isolated DC/DC converter to supply isolated power, enabling the miniaturization of multi-channel analog signal isolation systems. 【Features】 ■ Compact 45×35mm, low-profile 12mm package ■ Input/output signal voltage range: ±10V (when powered at +15V) ■ Gain: ×1 to 100 ■ Isolation between input and output: AC1,000V (min) ■ Isolation between channels: AC500V (min) ■ Frequency response: DC to 5kHz (typ) *For more details, please refer to the documentation. Feel free to contact us with any inquiries.

• Amplifier

The "SurLok Plus Series" is a single-pole waterproof connector that replaces traditional crimp terminal connectors. It adopts industry-standard wiring methods (crimping/screws/busbars), allowing for on-site wiring without the need for special tools. Utilizing RADSOK technology, it can handle currents of up to 350A while being compact in size. 【Features】 ■ Adopts industry-standard wiring methods (crimping/screws/busbars) ■ Allows for on-site wiring without the need for special tools ■ Rated: 1,000V (1,500V option available), maximum 350A ■ Dust and waterproof: IP67 (IP69K available) ■ Compact and robust housing * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Waterproof Connector
• connector
• Other Connectors

We would like to introduce the "Touch Sensor Module" manufactured by Neonode, which we handle. It can be used in various applications, including elevators, kiosk terminals, delivery box operation panels, and touch panel displays. In the related videos below, we provide explanations of the sensing principles and specifications, as well as illustrations of application examples for the touch sensor module. There is also a demonstration of actual touchless operation on aerial images, so please be sure to take a look. *For more details, please refer to the related links or feel free to contact us.

• Touch Panel
• Sensors

The "MF-LSMF series" is a resettable fuse designed to protect against overcurrent or overheating due to overcurrent. Available in a 2920 inch size with 24 combinations of circuit current and voltage to choose from. It can be used in Li-ion battery packs, low-voltage telecom equipment, PC motherboards, and portable electronic devices. 【Features】 ■ Protection against overcurrent or overheating due to overcurrent ■ High-power surface mount product ■ 4.7×3.3×2.9mm (H) ■ cUL, TUV certified ■ RoHS10 compliant, halogen-free * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic parts
• fuse

The "CPS Series" is a capacitive switch that combines high durability with a housing made of stainless steel. By eliminating movable parts from the actuator section, the switching cycle achieves a product lifespan of approximately 5 million cycles, along with dust and water protection rated IP67 and shock protection rated IK09. This product is suitable for applications that require not only durability but also visibility to distinguish the operation and function of equipment through color and design. 【Features】 ■ Two shapes: Ring illumination, Area illumination ■ Colors: Choose from single colors (red, green, blue, cyan, magenta, yellow, white), two colors (ON/OFF), or multi-color (RGB) ■ Three types of switching operation: Normally open, Normally closed, Latching ■ Three sizes: Diameter φ16, φ19, φ22mm *You can download the English version of the catalog. *For more details, please refer to the PDF document or feel free to contact us.

• switch
• switch

We would like to introduce our analog gas sensor, the "1 Series." This compact and slim sensor utilizes the highly reliable City Technology. It boasts a long lifespan and can operate across a wide range of temperatures and humidity levels. It can be used in the development of gas equipment, as well as in industrial portable devices and industrial safety equipment, and gas detectors. 【Features】 ■ Utilizes highly reliable City Technology ■ Slim and lightweight (20×20×10.3mm) ■ Long lifespan ■ Surface mount spring contact ■ Compatible with a wide variety of gases (CO/H2S/O2/SO2/flammable gases) * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• Sensors
• Sensors

The "DEUTSCH BAS 9 Connector Series" features a push-pull locking system designed for blind mating. The leading grip helps prevent unintentional disconnection. It achieves high performance and reliability in harsh aerospace, defense, and space environments. We also offer a wide variety of shell types and accessories, insert arrangements (38999 Series III), and multiple surface finish options. 【Features】 ■ Locking system compatible with blind mating ■ Interface and individual wire sealing ■ Durability: 500 mating cycles, with variations up to 1500 cycles ■ Standards SAE/AS81703 Series III ■ UTE model 93422HE 311 ■ MIL-DTL 38999 *For more details, please refer to the related links or feel free to contact us.

• Other Connectors
• connector

The "Push-fit Board-to-Board Connector" is a product that excels in low cost, high reliability, and design flexibility. It is available in 1-row and 2-row configurations, with a wide range of pitches, pin counts, and component selections between boards. The rated current is 2A (Max), and the pin counts are 2p/4p/6p/8p/10p. It is effective for various applications such as sensors, modules, speakers, and motors, as well as child boards or FPCs. 【Features】 ■ Usable for power or signal line connections ■ Pitch: 0.7mm, 1.1mm, 1.25mm, 1.5mm, 1.6mm, 2.0mm ■ Type: 1-row or 2-row ■ Rated current: 2A (Max) ■ Effective for space-saving and low-profile board-to-board connections on PCBs * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Board to Board Connectors
• connector
• Other Connectors

The "SM9000 series" is a MEMS sensor that supports a low pressure range of 125Pa and features a 16-bit I2C digital interface. It is offered in a gauge pressure and differential pressure configuration in a SOIC-16 package compliant with JEDEC standards. The total error band after automatic zeroing at the board mount and system level is less than 1% FS. 【Features】 ■ Differential pressure measurement range: ±125 and ±250Pa ■ Gauge pressure range: 0–250, 0–300, 0–600Pa ■ Total error band after automatic zeroing: less than 1% FS ■ 16-bit I2C digital interface ■ Pressure calibrated and temperature compensated output * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Sensors
• Sensors

The "PD-AS-951" is a high-power active splitter that can be used as a solution for non-PoE Ethernet powered devices or when you want to split the DC power and data signal lines on the PoE receiving side. It supplies power from a PoE hub or PoE injector, allowing for functional expansion even from an existing network. You can switch between 12V or 24V depending on the specifications and applications of the receiving side. 【Features】 ■ Functional expansion possible from an existing network ■ Split voltage 12V/24V (switchable) ■ IEEE802.3af/at compatible ■ High power output supports defogging heaters and wiper drives for PTZ cameras and outdoor surveillance cameras *For more details, please refer to the related links or feel free to contact us.

• power supply
• Other network tools
• Other electronic parts

The MCP6V86 is an operational amplifier that performs input offset voltage correction due to its ultra-low offset and offset drift. It has a bandwidth of 5MHz, virtually no 1/f noise, and provides excellent PSRR and CMRR. It operates with a low single supply voltage of 2.2V, with a maximum quiescent current of only 770uA (Max) per channel. 【Features】 ■ Supply Voltage: 2.0 to 5.5V (Single Supply) ■ Provides input offset voltage correction ■ 5MHz bandwidth ■ Stable at unity gain ■ Enhanced EMI protection * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Amplifier
• Other electronic parts

The WEO012864Z is a 0.96-inch COG type OLED display equipped with a control knob. It supports 4-wire SPI and I2C interfaces. The resolution is 128x64 dots, and it has an integrated SSD1306IC. The supply voltage (VCI) ranges from a minimum of 1.65V to a maximum of 3.3V, with a 1/64 duty cycle. 【Features】 ■ Built-in encoder allows operation beyond touch panel ■ Display colors: three colors - white, yellow, and blue ■ Supply voltage: 1.65 to 3.3V, duty cycle is 1/64 ■ Storage temperature: -30℃ to 80℃ ■ Operating temperature: -20℃ to 70℃ * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Organic EL
• LCD display

The "WF70A9SWAGDNT0" is a TFT LCD equipped with an IPS panel that has a wide viewing angle. It can operate in a temperature range of -30°C to 80°C. The viewing angles are left: 80/right: 80/up: 80/down: 80 degrees (Typ.), and the contrast ratio is 1000:1 (Typ.). The surface of the panel is treated with an anti-glare finish, and the screen aspect ratio is 15:9. 【Features】 ■ Module size: 165.8×106.61×8.0mm ■ LCD type: TFT, normally black, transmissive ■ Backlight: LED, normally white ■ Power supply voltage (VCC): 2.7V to 3.6V, with Typ. at 3.3V ■ Storage temperature: -30°C to 80°C ■ Operating temperature: -30°C to 80°C *You can download the English version of the catalog. *For more details, please refer to the PDF document or feel free to contact us.

• Touch Panel
• LCD display

The "WF32DSLAJDNN0" is a high-brightness type TFT that incorporates the ILI9341 driver IC. The contrast ratio is 500:1 (Typ.), and the viewing angle is at the 6 o'clock direction (grayscale inversion at the 12 o'clock direction), with an anti-glare treatment applied to the panel surface. It can be utilized in smart home applications, as well as in medical devices, security equipment, and measurement instruments. 【Features】 ■ Module size: 50.04×77.6×2.55mm ■ LCD type: TFT, normally white, transmissive ■ Backlight: LED, normally white ■ Resolution: 240×RGB×320 pixels ■ Storage temperature: -30℃ to 80℃ ■ Operating temperature: -20℃ to 70℃ * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• LCD display
• Touch Panel

We would like to introduce the "LCD Backlight Module" that we handle. To allow customers to compare and confirm the effects of the backlight, we provide samples of glass and backlight combinations. We offer TN type, STN type, and FSTN type. If you have any specific requests regarding combinations, please feel free to contact us, and we will consider the feasibility of accommodating your needs. 【Features】 ■TN Type - TN Positive Green - TN Negative Black ■STN Type - STN Positive Gray - STN Positive Yellow-Green - STN Negative Blue *For more details, please refer to the related links or feel free to contact us.

• LED Module

The Bourns Mini Breaker SC Series is a product suitable for protecting battery cells and USB power delivery. When overheating occurs, the bimetal opens and interrupts the current, while the PTC maintains the open state until the power is cut and the temperature drops to a safe level. This operation prevents chattering and improves product lifespan compared to standard bimetal products by reducing contact wear. - Surface mount type - Reusable - Overheating and overcurrent protection - Lineup with trip temperatures ranging from 72 to 85°C - The height of "SCxxAAB" is only 0.94mm ± 0.05mm (two height options) - Since its release, there have been zero reported issues in the market as of March 2022.

• fuse
• Other electronic parts

The "Fine Pitch ZIF Connector (0.25mm & 0.3mm)" is suitable for internal connections in compact and lightweight consumer devices. It adopts a flip lock and back flip lock mechanism to facilitate the insertion of FPC/FFC, preventing half-insertion and diagonal mounting, thereby improving workability. Additionally, with both top and bottom contact types and a wide range of pin counts, it can accommodate various applications. 【Features】 ■ Two types available: top contact and bottom contact ■ ZIF (Zero Insertion Force) structure ■ Compatible with FPC/FFC cables ■ Easy operation of FPC/FFC achieved through flip lock and back flip lock * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Other Connectors
• connector
• Other electronic parts

The U5200 is a pressure transducer designed for demanding commercial and heavy industrial applications. It is suitable for measuring liquid or gas pressure and can measure challenging media such as contaminated water, steam, and mildly corrosive fluids. The wetted surface is made of 316L stainless steel, and there are no O-rings or organic materials exposed to the pressure medium, ensuring excellent durability. 【Features】 ■ Maximum accuracy of ±0.1% ■ Compact size (24×24×82mm) ■ Various pressure ports and electrical configurations ■ High robustness ■ Gauge pressure, sealed pressure, absolute pressure, compound pressure * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Converters and Transducers
• Sensors
• Sensors

The "ME550," which adopts a capacitive measurement method, is a sensor suitable for measuring very low pressures of 60 mbar. It features high pressure resistance and is well-suited for applications such as semiconductor manufacturing equipment, agricultural measurement devices, and meteorological measurement devices. The Al2O3 ceramic provides excellent chemical resistance (to corrosive gases, most solvents, acids, etc.). 【Features】 ■ Capacitive measurement method ■ Chemical resistance (acid and alkali resistance) ■ Mechanical robustness ■ Wide operating temperature range ■ Ultra-low pressure measurement: 0–60 mbar * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Sensors
• Sensors
• Safety Sensors

The "RRC1130 (3.80V/3.88Ah)" is a standard lithium-ion secondary battery designed with a focus on safety, compliant with safety certification standards from around the world. Thanks to RRC's manufacturer policy of not conducting EOL (End of Life), it is possible to introduce the product with peace of mind while keeping initial costs low. By using I2C communication to read battery information such as operating time, temperature information, and electrical specifications, more efficient management can be achieved. 【Features】 ■ Extensive adoption in medical and industrial equipment ■ Nominal voltage/rated capacity: 3.80V/3.88Ah ■ Dimensions/weight: 84.0×61.2×6.7mm/69g ■ Compliant with worldwide safety certification standards ■ No EOL as a model number * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• Secondary Cells/Batteries
• Lithium-ion battery

The RRC1120 (3.60V/2.35Ah) is a standard lithium-ion secondary battery designed with a focus on safety, compliant with safety certification standards from around the world. Thanks to RRC's manufacturer policy of not conducting EOL (End of Life), it is possible to introduce the product with peace of mind while keeping initial costs down. By reading battery information such as operating time, temperature information, and electrical specifications through I2C communication, more efficient management can be achieved. 【Features】 ■ Widely adopted in medical and industrial equipment ■ Nominal voltage/rated capacity: 3.60V/2.35Ah ■ Dimensions/weight: 52.5×35.0×11.2mm/42g ■ Compliant with worldwide safety certification standards ■ No EOL for the model number * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Secondary Cells/Batteries
• Lithium-ion battery

Neonode's "Touch Sensor Module" enables non-contact operation of touch panel displays and aerial images through sensing that utilizes its proprietary "zForce® Technology." By detecting objects within the sensing area using infrared, it allows for sensing while wearing gloves, using something other than fingers, or in combination with a hologram plate, thus enabling interaction with aerial images. We propose applications for safe and secure non-contact solutions that match the new normal era. 【Features】 ■ Sensing is possible while wearing gloves or using something other than fingers ■ Standard lineup includes 9 sensor sizes ranging from 115mm to 346mm (Please consult us for specific sensor size requests) ■ Touch interaction with aerial images using a hologram plate is possible ■ Support for large screens is possible using 2 or 4 sensors *For more details, please refer to the materials. ★ If you would like to see a demo unit, please feel free to contact us.

• Other electronic parts

The "MGS004-F" is a tool that contributes to creating a comfortable environment by visualizing air quality. To maintain a comfortable indoor environment, it is important to visualize CO2 concentration, VOCs (volatile organic compounds), temperature, and humidity, and to ensure proper ventilation. Not only does an increase in CO2 concentration raise the risk of infectious diseases, but there is also data indicating that it can lead to decreased concentration and work efficiency. This product employs a high-precision NDIR dual-wavelength method for the CO2 sensor and features an automatic calibration function, allowing for 10 years of maintenance-free use. 【Features】 ■ Maintenance-free for 10 years with automatic calibration ■ Covers an area of up to 50m2 with a single unit ■ Can be linked with a dedicated PC app for large screen display and smart plug integration ■ Compliant with subsidies for infectious disease countermeasures *For more details, please refer to the documentation. Feel free to contact us with any inquiries.

• Other measurement, recording and measuring instruments

The "ME501/ME505" is a ceramic pressure sensor that employs a piezoresistive method. It is thermally compensated by a laser-adjustable PTC resistor, ensuring high linearity across the entire range due to the use of ceramics. Measurements can be taken with minimal hysteresis effects. It has excellent chemical resistance due to the use of Al2O3 ceramics. 【Features】 ■ Excellent durability, corrosion, and wear resistance ■ Measurement of absolute pressure ■ Thermal compensation ■ Extensive customization ■ Wide measurement range *You can download the English version of the catalog. *For more details, please refer to the PDF materials or feel free to contact us.

• Sensors

The "42F Series" is the shortest RJ45 magjack offered by YDS. Therefore, we strongly recommend it to customers who are concerned about space in their designs. We offer both products with and without LED. They comply with IEEE 802.3 and ANSI X3.263, and are RoHS directive compliant. With a shielded case, it is less susceptible to noise interference from devices. 【Features】 ■ Low profile at 11.3mm ■ Compatible with 10/100 Base-T ■ Built-in pulse transformer for a good space factor ■ Shielded case minimizes noise interference from devices ■ 100% electrical characteristic testing before manufacturer shipment * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Other Connectors

The product "13F-66BNDK2NL" is our number one selling RJ45 modular jack. As such, it is a versatile component with proven performance in various applications and is compatible with major PHYs. This product features a compact design that saves space on PCB boards. It complies with IEEE 802.3 and ANSI X3.263 and is RoHS directive compliant. 【Features】 ■ Supports 10/100 Base-T ■ Built-in pulse transformer for good space factor ■ Shielded case to minimize the impact of device noise ■ 100% electrical characteristic testing before manufacturer shipment ■ Our number one selling RJ45 modular jack ■ Versatile component with proven performance in various applications * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Other Connectors

The UCS3205 is a 5A, 22V bidirectional load switch equipped with a fast role swap feature. It includes Fast Role Swap (FRS) functionality, bidirectional current capability, configurable overcurrent protection, automatic recovery fault handling, overvoltage lockout, reverse voltage protection, slew rate control, fast output discharge, and scaled analog. 【Features】 ■ Bidirectional channel load switch from 2.85 to 22V ■ Supports 5A continuous current ■ 30mΩ typical on-resistance ■ Current limiting can be set with external resistors ■ Fast role swap feature (FRS) compliant with USB * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• power supply
• switch

The "0.4mm Fine Pitch Board-to-Board Connector" has been developed for internal connections in compact or slim portable devices. It features a space-saving design and a terminal locking mechanism with a double contact structure, ensuring high reliability during mating. Additionally, the contact terminals of the receptacle are plated with a nickel barrier to improve the assembly process, such as preventing solder wicking. 【Features】 ■ SMT method compatible with high-density mounting ■ Rated current: 0.3A ■ Rated voltage: 30VAC ■ Number of pins: 8p, 10p, 30p, 34p, 40p * You can download the English version of the catalog. * For more details, please refer to the PDF document or feel free to contact us.

• Other Connectors

The "Spring Finger Terminal" can be used in PCBs across various industrial fields. It can be utilized as a ground to prevent EMI noise and static electricity generated from vibrating components such as speakers, motors, and microphones, as well as for antenna feeding or low-voltage connection applications. It features a closed-loop contact design that ensures reliable connections to the PCB, excellent resistance values, and high current capacity. 【Features】 ■ Used as a ground between the device and the PCB ■ Market-leading compact size of 1.7mm², effective for PCB space saving ■ Cost-effective solution for various types of devices ■ Usable heights from 0.4mm to a maximum of 7mm * You can download the English version of the catalog. * For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic parts