The catalog for the ultrasonic spray nozzle has been updated!

Spraying fine particles without pressure! Atomization through the vibration of piezoelectric ceramics!! Low power consumption and low energy costs!!

Ultrasonic waves generated by piezoelectric ceramics are transmitted to the spray nozzle (atomizer), where they vibrate the liquid film to create extremely fine particles for spraying. Liquid can be supplied and sprayed into fine particles without the need for pressurization. The flow rate varies depending on the model, but it can accommodate a wide range from a minimum flow rate of 10 ml/min to a maximum of 100 ml/min. Since pressure is not applied to the liquid, there is very little splatter or rebound, eliminating waste of the applied liquid. Additionally, there is no need for a large painting booth. This achieves a reduction in capital investment and running costs. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia Corporation.

• Ultrasonic Oscillator
• nozzle
• valve

We will achieve a reduction in equipment investment and running costs.

The ultrasonic spray nozzle (atomizer) transmits vibrations from the piezoelectric ceramic, causing the liquid film to vibrate and forming fine particles for spraying. Liquid is supplied without pressure, allowing for the spraying of fine particles. It accommodates a wide range of liquid flow rates from a minimum of 10 milliliters per minute to a maximum of 100 milliliters per minute. Since no pressure is applied to the liquid, there is very little splatter or rebound, eliminating waste of the coating liquid and making large painting booths unnecessary.

• Ultrasonic Oscillator
• nozzle
• Other processing machines

A fixture for spreading wider than a wide-angle air transport fixture.

Dove Tail Spray Shaper The Dove Tail Spray Shaper is an air transport fixture, ideal for wide-angle spraying and flux coating. It can be used with all spray nozzles of NS and WS types. By changing the position of the Dove Tail Spray Shaper, it is possible to switch from a fan-shaped spray pattern to an elliptical spray pattern. *This product is a dedicated accessory for the ultrasonic spray nozzles manufactured by Sonia Corporation.

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

The Sonia Corporation's ultrasonic particle size generator transforms liquids into fine particles!

The ultrasonic particle generator transforms low-viscosity liquids into fine particles. Our company's compact 2.4MHz NO model 241T uses a Teflon-coated nebulizer. This device is fully microcontroller-based, allowing users to program operating parameters while handling various applications for actual particle generation. The front panel is equipped with an LCD that enables users to vary the particle generation rate from 0% to 100% in 5% increments. For special processes, such as applying small parts, a device is incorporated that can adjust the flow rate between 0-2 cfm to move particles out of the vessel where they are created. This air source and all other connections feature easily removable 304SS fittings and Teflon O-rings, allowing for easy adaptation to cleaning, external gas supply, or vacuum connections. The 304SS Tee (also available with Teflon coating) is designed to trap particles, with a small amount of airflow/gas/vacuum used to move particles from the device.

• Ultrasonic Oscillator
• Other physicochemical equipment
• others

Atomization of liquid without pressurization by piezo vibration. Enables uniform application while reducing power consumption and liquid waste.

Ultrasonic waves are transmitted to the nozzle through the vibration of piezoelectric ceramics, vibrating the liquid film to form and spray fine particles. It can handle a wide range of liquid flow rates from a minimum of 10 ml/min to a maximum of 100 ml/min, with a nearly constant particle size across the entire flow range. ◆Product Features◆ - Energy-saving as it can supply liquid with low power without pressurizing - Uniform atomization regardless of flow rate - Nearly constant particle size across the entire flow range - Resistant to clogging, ensuring high operational safety - Good coating efficiency due to the slow self-velocity of particles - Maximum flow rate for standard specifications is 100 ml/min - Operating frequency ranges from 20 to 130 kHz (varies by model) - Outer particle size ranges from 11.8 to 42 μm (varies by model) ◆Accessories◆ By using an air transport device, it is possible to freely change the spray shape of the applied fine particles (droplets). ◆Liquid Delivery Pump◆ Precise control is possible by using a syringe pump or similar for liquid delivery. ≪Key Point≫ Demo units are available for loan, so please feel free to contact us. ※※Ultrasonic Cleaning Equipment※※ Sonosis also manufactures and sells ultrasonic cleaning equipment.

• CMP Equipment
• spray
• Coating Machine

Atomize the coating liquid with piezo vibration! Minimal splatter and rebound without pressure! Compatible with a wide range of flow rates.

The Sonia Corporation's "Ultrasonic Spray Nozzle" utilizes piezoelectric vibrations to vibrate liquids. It forms fine particles and sprays them. It can accommodate a wide range of liquid flow rates from 10 mL/min to 100 mL/min, and since it does not apply pressure to the liquid, it features minimal splatter and rebound. There is no waste of the application liquid, and a large booth is not necessary. It is suitable for applications such as coating, humidifying, and disinfecting. 【Features】 - Resistant to clogging and has high operational safety - Uniform ultrasonic atomization regardless of liquid flow rate - Low power consumption and inexpensive running costs - Available in two types: wide spray and narrow spray. ★ We are currently offering a demo unit for you to try out! ★

• Other processing machines

Affordable and with a wide selection!

We have prepared fluororesin and silicone according to the materials to be delivered. The fluororesin tubes are available in AWG standards, while the silicone tubes are available in millimeter sizes.

• dispenser
• Dispenser
• Other physicochemical equipment

This product is suitable for applying and dispensing instant adhesives, anaerobic liquids, and solvents both manually and automatically.

By using Teflon tubes, it has become possible to apply and dispense liquids that could not be handled with conventional rubber-based tubes. Additionally, since the liquid contact part is within the tube, there is no need to directly clean the pump mechanism; simply replacing the tube suffices. To ensure that no liquid remains wasted in the tubing, a forward and reverse rotation function has been implemented in the pump mechanism, making liquid replacement very easy. If there is an AC100V power supply, work can be started immediately.

• Filling and bottling machines
• Other physicochemical equipment

A fixture for applying particles sprayed from an ultrasonic spray nozzle over a wide area.

The wide-angle air transport fixture is a device that uses gas or air to expand the spray angle. The wide-angle air transport fixture can be attached to the Narrow Spray models 60K50T and 130K50T. There is an air supply port on the side of the wide-angle air transport fixture. By injecting gas or air, the gas or air circulates inside, causing the particles sprayed from the ultrasonic spray nozzle to spread and be pushed out. By adjusting the gas volume, air volume, pressure, and the tip of the ultrasonic spray nozzle, a spray angle of up to approximately 100° can be achieved. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia.

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

Designed to use fast-reacting liquids and capable of stirring in a short time!

The Sonia dual micro feed tube is designed to use fast-reacting liquids and can be stirred in a short amount of time. The material is stainless steel. The dual micro feed tube has two liquid supply ports, one at the top and the other on the side. *This product is a dedicated accessory for Sonia ultrasonic spray nozzles.*

• nozzle
• others

Designed for ultra-low flow rates of 1 ml/min or less.

The stainless steel micro feed tube made by Sonia is designed for extremely low flow rates of less than 1 ml/min. *Of course, it can also be used at flow rates above 1 ml/min. The liquid flows through without touching the tip, which forms a uniform particle size. *This product is an accessory specifically for Sonia's ultrasonic spray nozzle.

• nozzle
• spray
• others

Designed for fluids that have a strong impact on stainless steel, such as pharmaceutical-related applications.

The Sonia Corporation's PTFE fluoropolymer microfeed tube is designed specifically for fluids that have a strong impact on stainless steel, particularly for pharmaceutical-related applications. The liquid must be completely isolated for reasons of hygiene and chemical reactions. *This product is an accessory specifically for Sonia Corporation's ultrasonic spray nozzle.

• nozzle
• Water Hydraulic Equipment
• others

It precisely sprays fine particles!

The pinpoint air transport fixture generates high-quality, fine particles and can uniformly apply them to medical coatings and other small precision devices. The spray speed is slow, making it suitable for applying expensive chemicals in a thin layer with minimal use. It excels not only in coating and manufacturing applications for medical precision instruments but also in uses such as stent coating and catheter coating, providing excellent reproducibility of spray speed and particle diameter, while significantly reducing the consumption of the coating agent. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia Corporation.*

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

Air transport fixture for spraying in a square or rectangular shape.

This is an air transport device designed to spray particles from an ultrasonic spray nozzle in a square or rectangular shape. Its main application is for coating purposes. By adding a small amount of gas or air, it applies to square, rectangular, or flat substrates. By adjusting the distance from the workpiece and the pressure of the transport gas or air, various sizes and shapes of spray patterns can be achieved with the ultrasonic spray nozzle manufactured by Sonia. *This product is a dedicated accessory for the ultrasonic spray nozzle made by Sonia.*

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

Kaitaku Co., Ltd. has recently celebrated its 23rd anniversary. We would like to express our heartfelt gratitude to all our customers, partner companies, and stakeholders who have supported us thus far. Currently, Kaitaku is focusing on the "Hyper CLT Mats," which utilize wood CLT in the civil engineering field. We are proposing a new option of wood in places where steel plates have traditionally been used, such as temporary roads, access roads, heavy machinery work yards, and material yards. These mats are lightweight and easy to install, and they possess unique characteristics of wood, such as reducing glare and noise, CO2 fixation, and consideration for aesthetics. The Hyper CLT Mats are registered technologies with the Ministry of Land, Infrastructure, Transport and Tourism under NETIS, with the **NETIS registration number "TH-250021-A."** As we mark our 23rd anniversary as a new milestone, we will continue to expand the possibilities of wood, NETIS, civil engineering, and civil engineering CLT, delivering new value to civil engineering sites across the country.

Features ● Supports Intel LGA1851 socket processor (Arrow Lake-S) (sold separately) ● Equipped with Q870 chipset ● DDR5 CSO-DIMM dual channel support, up to 96GB ● 2.5GbE x 2, HDMI x 2, DisplayPort x 2, LVDS/eDP x 1 ● USB 3.2 Gen2 x 7, USB 2.0 x 4, RS-232/422/485 x 2, RS-232 x 4 ● DC-in 12V to 36V support

Features ● Supports Intel LGA1851 socket processors (Arrow Lake-S) with W880 chipset (CPU sold separately) ● DDR5 CSO-DIMM 2 slots, up to 96GB, ECC supported (sold separately) ● 2.5GbE LAN x 2 ● HDMI x 2, DP x 1, Type-C DP x 1, LVDS/eDP x 1 ● SATA x 2, M.2 M-key 2280 x 1 (NVMe), M.2 M-key 2240 x 1 (NVMe), M.2 E-key x 1, M.2 B-key x 1, PCIe Gen5 x16 x 1 included ● USB 3.2 Gen2 x 7, USB 2.0 x 4, RS232/422/485 x 2, RS232 x 4 included ● DC 12V to 36V * This model does not include memory, storage, or OS.

Features ● Supports Intel LGA1851 Gen socket processors (Arrow Lake-S), equipped with H810 chipset (CPU sold separately) ● DDR5 CSO-DIMM x2, maximum 96GB (sold separately) ● 2.5GbE x2 ● HDMI x 2, DP x 1, Type C x 1, LVDS/eDP x 1 supported ● SATA x 2, M.2 2280 M-key x 1 (NVMe), M.2 E-key x 1, M.2 B-key x 1, PCIe Gen5 x16 x 1 ● USB 3.2 Gen2 x 4, USB 2.0 x 3, RS232/422/485 x 2, RS232 x 4 ● DC 12V to 36V input supported * This model does not include memory, storage, or OS.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can cause changes in the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.