ウェーブクレスト Product Lineup

A powerful and flexible tool for testing broadcast and RF devices. It offers reliable automatic measurements and a wealth of features, including a tracking generator and multiple operating modes.

• Other electronic measuring instruments
• EMC Testing

**Product Overview** The TBL0550-1 5µH LISN is a device necessary for setting up conducted noise measurements of electronic equipment powered by DC sources. It is designed to comply with CISPR 16-1-2, CISPR-25, EN55025, MIL-STD-461F, and ISO11452-4, and is intended for measurements in the frequency range of 150kHz to 110MHz, with limited use of DO-160 / ED-14G and ISO7637-2. The LISN is inserted into the supply line of the DUT (Device Under Test). Conducted noise present at the power terminals of the DUT can be measured using a spectrum analyzer or measurement receiver via a BNC connector. The source (power) terminal and the DUT terminal are decoupled by a 5µH inductor. By combining two TBL0550-1 units with the Tekbox LISN Mate, common mode noise and differential mode noise can be measured separately. The unit is equipped with a BNC male to N male RG232 cable, a coupling connector, and a ground bracket for connection to a ground plane.

• EMC Testing
• Testing Equipment and Devices
• Optical Measuring Instruments

【Product Overview】 The TBL5016-2 is a line impedance stabilization network designed to measure line-conducted interference in the range of 9kHz to 30MHz, in accordance with the CISPR 16-1-2 standard. This device is designed to test single-phase AC power supplies with a maximum supply voltage of 240V and 16A. Conducted noise can be measured on both the phase and neutral lines. The TBL5016-2 is equipped with a switchable limiter/attenuator and an artificial manual connection. This device is available with country-specific DUT connectors.

• EMC Testing
• Testing Equipment and Devices
• Optical Measuring Instruments

【Product Overview】 The TBLC08 50μH LISN is a line impedance stabilization network designed to measure line-conducted interference in the frequency range of 9kHz to 30MHz, in accordance with the CISPR16 standard. This device is designed to test single-phase AC power supplies with a maximum supply voltage of 240V. Conducted noise can be measured on both the phase and neutral lines. The TBLC08 features a switchable limiter/attenuator and an artificial hand connection. This device is available with country-specific DUT connectors.

• EMC Testing
• Testing Equipment and Devices
• Optical Measuring Instruments

The TBMDA4 modulated wideband power amplifier is designed to create a low-cost signal source for immunity testing of electronic building blocks and products, driven by the output of a spectrum analyzer's tracking generator. It can boost the output power of the tracking generator up to 5W within an input power range of -5 dBm to 0 dBm. It ideally complements the TBMDA3, which covers a frequency range of 10 MHz to 1 GHz from 100 kHz to 50 MHz. The TBMDA4 is ideal for driving Tekbox near-field probes to find sensitive spots in electronic circuits, creating electric fields of up to 550 V/m when driving the TEM cell TBTC0, and 300 V/m when driving TBTC1. When driving TBTC2 or TBTC3, it generates 100 V/m. The test signals for immunity testing can be CW, AM, or PM modulated, providing built-in modulation capabilities to generate 1 kHz AM or PM signals. In PM mode, the TBMDA4 can also generate a 217 Hz signal with a 12.5% duty cycle to simulate mobile phone TDMA noise.

• Other electronic measuring instruments
• EMC Testing

The TBMDA3 wideband power amplifier with modulation capability is designed to create a low-cost signal source for immunity testing of electronic building blocks and products. It is intended to be driven by the tracking generator output of a spectrum analyzer. Its high gain allows it to boost the output power of any tracking generator up to 5W. The TBMDA3 is ideal for driving Tekbox near-field probes to find sensitive spots in electronic circuits, or for generating electric fields of up to 550V/m when driving the Tekbox TEM cell TBTC0, 300V/m when driving TBTC1, and 100V/m when driving TBTC2 or TBTC3. The test signals for immunity testing can be modulated in CW, AM, or PM. As a result, the TBMDA3 provides built-in modulation capabilities to generate 1 kHz AM or PM signals. In PM mode, the TBMDA3 can also generate a 217 Hz signal with a 12.5% duty cycle to simulate mobile phone TDMA noise.

• Other electronic measuring instruments
• EMC Testing

The TBDA1/28dB wideband driver amplifier is a highly versatile building block that can be easily integrated into lab setups. With a frequency range of 40MHz to 3GHz and an output power of +22dBm at 1dB compression, these amplifiers are ideal for boosting the amplitude of low-power RF sources or driving power amplifier stages. The TBDA1 wideband amplifier is available with a gain of 28dB.

• Other electronic measuring instruments
• EMC Testing

The TBDA1/14dB wideband driver amplifier is a versatile building block that can be easily integrated into lab setups. With a frequency range of 40MHz to 3GHz and an output power of +22dBm at 1dB compression, these amplifiers are ideal for boosting the amplitude of low-power RF sources or driving power amplifier stages. The TBDA1 wideband amplifier is available with a gain of 14dB.

• Other electronic measuring instruments
• EMC Testing

The TBMDA2 wideband driver amplifier with modulation capabilities is designed to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is intended to be driven by the tracking generator output of a spectrum analyzer. With a +27dBm 1dB compression point, it can boost the output power of the tracking generator up to 500mW. The TBMDA2 can drive Tekbox near-field probes to find sensitive spots in electronic circuits, create electric fields of up to 170V/m when driving the Tekbox TEM cell TBTC0, and is optimal for 100V/m when driving TBTC1 at 50V/m. When driving TBTC2 or TBTC3, it can produce 30V/m. The test signals for immunity testing can be CW, AM, or PM. As a result, the TBMDA2 provides built-in modulation capabilities to generate 1 kHz AM or PM signals. In PM mode, the TBMDA2 can also generate a 217 Hz signal with a 12.5% duty cycle to simulate mobile phone TDMA noise.

• Other electronic measuring instruments
• EMC Testing

The TBMDA1 modulated wideband driver amplifier is designed to create a low-cost signal source for immunity testing of electronic building blocks and products. It is intended to be driven by the output of a spectrum analyzer's tracking generator. With a gain of 22 dB and a 1 dB compression point of +22 dBm, it can boost the output power of the tracking generator up to 150 mW. The TBMDA1 is ideal for driving Tekbox near-field probes to generate electric fields of up to 50 V/m when finding sensitive spots in electronic circuits or when driving the Tekbox TEM cell TBTC1, or 25 V/m when driving TBTC2, or 18 V/m when driving TBTC3. The test signals for immunity testing can be CW, AM, or PM. As a result, the TBMDA1 provides built-in modulation capabilities to generate 1 kHz AM or PM signals. In PM mode, the TBMDA1 can also generate a 217 Hz signal with a 12.5% duty cycle to simulate mobile phone TDMA noise.

• Other electronic measuring instruments
• EMC Testing

The TBHDR1 from TekBox Digital Solutions is an ideal alternative preamplifier for EMC test application spectrum analyzers and receivers due to its high IP3 and low noise figure. With its low noise figure, high IP3, and gain up to the kHz range, it also performs exceptionally well as an amplifier for active loop antennas.

• Other electronic measuring instruments
• EMC Testing

**Main Features** - Maximum output frequency of 100MHz - 500MSa/s sample rate, vertical resolution of 1μHz - 14-bit vertical resolution, 10 Marb waveform length - Comprehensive waveform output: 6 basic waveforms and 150 built-in arbitrary waveforms - Comprehensive modulation functions: AM, FM, PM, FSK, 4FSK, PSK, OSK, ASK, BPSK, PWM, sweep, burst - High-precision frequency counter integrated, supporting a range of 100mHz-200MHz - Supports SCPI and LabVIEW - 7-inch (800×480 pixels) multi-touch screen, supported

• Signal Generator

The SIGLENT SSA3000X Plus series spectrum analyzers are powerful and flexible tools for RF signal and network analysis.

• Other electronic measuring instruments
• EMC Testing

The new series recorders DAS30/50/60 are designed to meet the requirements of all applications in the industry (IEC61010, CAT. III 600V). You can view measurements (traces, digital values) and directly access recordings from internal memory or USB memory. Additionally, using Sefram software, you can easily transfer recordings to a computer.

• Recorders
• Voltage Meter
• Other measurement, recording and measuring instruments

The TBFL1 is a combination of a transient limiter, attenuator, and high-pass filter, designed to optimally protect the input of a spectrum analyzer or measurement receiver when performing conducted noise measurements or other measurements where the input level cannot be reliably predicted or where accidental overloads may occur. By combining pins and Schottky diodes with a multi-stage 10dB attenuator, it becomes a device capable of withstanding continuous RF input levels of up to 5W (37dBm). A gas discharge tube provides additional protection against high-voltage transients. Furthermore, a 9 kHz high-pass filter suppresses harmonics of the power supply voltage. With a limiting threshold of +11dBm and a flat frequency response from 9 kHz to 600 MHz, the TBFL1 limiter can be used as a protective device for the entire range of conducted noise measurements and in many other applications.

• Other electronic measuring instruments
• Other measurement, recording and measuring instruments
• EMC Testing

【Product Overview】 + Infrared thermal image resolution of 320×240 + Three fusion modes of visible and infrared + Three image enhancement modes for various applications + Customized upper and lower temperature alarms + Computer analysis software for more specialized industry applications + Multiple measurement methods to ensure temperature is not hidden anywhere + Five color palettes (Black Hot, White Hot, Rainbow, Iron, Enhanced Iron) + Large internal memory capable of storing up to 20,000 images + Temperature measurement range of -20°C to 350°C + Adjustable emissivity (0.01-0.99), default 0.95 + Image capture using three image storage for multi-view analysis + 3.5-inch TFT LCD

• Other electronic measuring instruments
• Optical Measuring Instruments
• Surveillance Cameras

【TBCP1-200】 The TBCP1-200 is a fixed aperture RF current monitoring probe. The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transmission impedance is > 14 dB ohms in the range of 40 kHz to 200 MHz. 【TBCP1-250】 The TBCP1-250 is a fixed aperture RF current monitoring probe. The probe shows a very flat response with a 3dB bandwidth of 250 MHz and is characterized and usable in the frequency range of 30 kHz to 250 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transmission impedance is > 16 dB ohms in the range of 300 kHz to 250 MHz. 【TBCP1-500】 The TBCP1-500 is a fixed aperture RF current monitoring probe. The probe shows a very flat response with a 3dB bandwidth of 500 MHz and is characterized and usable in the frequency range of 30 kHz to 500 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transmission impedance is > 15 dB ohms in the range of 300 kHz to 500 MHz.

• EMC Testing

The TBWA2 wideband RF amplifier from TekBox Digital Solutions is a versatile building block that can be easily integrated into laboratory setups. With a bandwidth of 2MHz to 6GHz, it is ideal for amplifying signals picked up by EMC near-field probes. The TBWA2 wideband amplifier is available with a gain of 20dB or 40dB.

• Other electronic measuring instruments
• EMC Testing

Set of four types of magnetic field (H) and electric field (E) probes for radiated emission EMC pre-compliance measurements.

• Other electronic measuring instruments
• EMC Testing

<Managing Indoor Environment with a Smartphone> Connect your smartphone to Aranet4 via Bluetooth using the iOS or Android app to configure device settings, view historical data, and set alarms and sensor reading frequencies. Aranet4 monitors §carbon dioxide (CO2) §temperature §humidity §atmospheric pressure. <Carbon Dioxide Monitor Aranet4 is also active in agriculture and livestock sectors!!> https://wavecrestkk.co.jp/wc/news/aranet4co2-monitor/

• Other office supplies
• Other measurement, recording and measuring instruments
• Other environmental analysis equipment

- Frequency range from 9 kHz to 1.6 GHz / 3.6 GHz - -160 dBm DANL (Displayed Average Noise Level) - Phase noise -80 dBc / Hz @ 1GHz @ 10 kHz offset - Minimum resolution bandwidth (RBW) of 10Hz - Total amplitude accuracy of 1.5dB - EMI pre-compliance test capability, optional EMC test software available - Standard pass/fail on-site test alert function - Lithium-ion battery, operating life of up to 4-6 hours - Optional 1.6GHz / 3.6GHz tracking generator, 3.6GHz signal generator - Standard GPS receiver, optional antenna, capable of recording latitude/longitude information and test information - 8-inch (1024 * 768) IPS LCD touchscreen, wider viewing angle, built-in light sensor to adjust screen backlight according to ambient light.

• Other electronic measuring instruments
• EMC Testing

- Frequency range from 9 kHz to 3.6 GHz - Displays an average noise level of 150 dBm - Phase noise -85 dBc/Hz at 1 GHz with a 10 kHz offset - Overall amplitude accuracy <1.5 dB - Minimum resolution bandwidth (RBW) of 10 Hz - EMI pre-compliance test kit - 1.5 GHz tracking generator kit - 10.4-inch display

• Other electronic measuring instruments
• EMC Testing

<Excellent Operability> - 10.1-inch display with a resolution of 1024x600 - Capacitive touchscreen that supports multi-touch gestures, allowing efficient movement or scaling of traces with finger touches - Built-in web server supports remote control of the LAN port using a web browser. <High Resolution and Low Noise> By combining 10-bit mode and zoom, waveform noise can be displayed in greater detail. The vertical and horizontal zoom functions of the SDS2000X Plus allow users to select areas and enlarge captured signals for more detailed analysis. <Power Loop Response Analysis (Board Plot)> Stability is a very important metric in power supply design. Generally, stability measurements require a special frequency response analyzer, which can be very expensive. Siglent offers an affordable solution. <Measurement of Parameters and Parameter Statistics> Parameter measurements fall into four categories: horizontal, vertical, other, and channel delay, allowing for a total of over 50 types of measurements.

• oscilloscope

The LF Personal Monitor WaveMon LF-400 monitors magnetic fields from DC to 10Hz to 400KHz. 【Main Features】 - Data logger - Relative value display design that is easy for the wearer to see - Six-level alarm LED display, alarm sound, vibration - Compliance with international standards - ICNIRP, 2013/35/EU, IEEE standards With a user-friendly design, it is gaining popularity worldwide, especially in Europe. 1. Display design that is easy for the wearer to see 2. Arm belt included 3. Ergonomic body design 4. Compact at just 194g 5. Three types of alarm methods: LED, sound, vibration 6. GPS, altimeter (optional)

• Data Logger
• EMC Testing
• Other environmental equipment

The 5G next-generation communication networks and autonomous driving technologies in the automotive field, which are being developed for practical use and commercialization in 2020, require measurement technologies for onboard millimeter-wave and sub-millimeter-wave radar. SAF's Spectrum Compact series covers a wide frequency range from 300 MHz to 87 GHz with eight models. Customers can choose the most cost-effective and optimal model tailored to their applications. The devices will not only satisfy standalone measurements in the field but will also be suitable for serious research and development with standard PC analysis software.

• Other electronic measuring instruments
• EMC Testing
• Other measurement, recording and measuring instruments

• High-precision measurement of electric and magnetic fields with a single device • Wide frequency range from DC to 90GHz (via probe) and high dynamic range • Selective and broadband measurements in all three axes through FFT processing • Weighted peak measurements in accordance with the EMF Directive 2013/35/EU • Compliance with international standards such as ICNIRP, IEC, EN, IEEE, etc. • Accurate location information can be obtained with the GPS option

• Other electronic measuring instruments
• EMC Testing
• Environmental Test Equipment

【Features】 - High dynamic range 60dB - Isotropic & effective value measurement - Excellent attenuation - International standard compliance

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

This product has also been adopted at airports in Paris. 【Features】 - High-precision measurement of electric and magnetic fields - Wide frequency range and high dynamic range - Isotropic & true RMS measurement - Spectrum analysis - Selective and broadband measurements in all three axes through FFT processing - Compliant with international standards

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

Complies with IEC/EN62233, IEC/EN62822, and IEC/EN62311 standards. Ideal for measurements where small size and spatial resolution are important. 【Main Features】 - High-precision measurement of electric and magnetic fields with a compact 3cm² electromagnetic field sensor - Isotropic & true RMS measurement - Spectrum analysis - Equipped with FFT mode - Complies with international standards IEC/EN62233, IEC/EN62822, and IEC/EN62311

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

The world's top brand in "RF Safety," Wavecontrol, introduces the portable electromagnetic field monitor WaveMon, now featuring a new personal exposure monitor for 5G frequencies ranging from 1MHz to 60GHz. 【Main Features】 - Equipped with a 3-axis sensor - Isotropic & RMS measurement - Display design that is easy to read for the user - Six levels of alarm: LED display, alarm sound, vibration - Compliant with international standards - ICNIRP, EMF Directive 2013/35/EU, FCC, SC6 Designed with the user in mind, it is gaining popularity worldwide, especially in Europe. 1. User-friendly display design 2. Includes arm belt 3. Ergonomic body design 4. Compact at just 190g 5. Three types of alarm methods: LED, sound, vibration 6. GPS, altimeter (optional)

• Data Logger
• EMC Testing
• Other environmental equipment

【Product Overview】 The MonitEM-Lab indoor EMF monitor has been specially developed for laboratories, working centers, industries, military, and airport facilities. It is optimized for high-frequency applications such as future 5G bands. 【Key Features】 ★ 24/7 Monitoring: Continuous monitoring 24 hours a day, 365 days a year ★ Alarms: Real-time audible and visual alarms ★ Wideband Measurement: Easy indoor RF monitoring of human exposure ★ Compliant with ITU-T K.83 ★ Control Center: Software for system management (optional) 【Compatible Probes】 E-Field: WPF3, WPF6, WPF8, WPF18, WPF40 H-Field: WPH1000

• Other electronic measuring instruments
• EMC Testing
• Environmental Test Equipment

The SIGLENT SSG3000X series signal generators have a frequency range of 9 kHz to 2.1 GHz / 3.2 GHz. They provide standard analog modulation such as AM, FM, and PM. Additionally, when used with baseband generators like the SDG6000X, they can generate IQ modulated signals. The SSG3000X series, with its high precision and pure output, is ideal for research and development, education, and manufacturing.

• Signal Generator

Model: TBTC0 Length: 390 mm Width: 100 mm Height: 62 mm Septum Height: 28 mm Rectangular Area Under the Septum: 19 cm x 7 cm x 2.8 cm TEM Cell Connector: N-Female Nominal Cell Impedance: 50 Ohm Wave Impedance: 377 Ohm Maximum RF Input Power: 10W (limited by supplied 50 Termination) Input Return Loss: S11 Maximum 3.15GHz < -15dB Wave Loss: Maximum 3GHz < 3dB, Maximum 6GHz < 4dB

• Other electronic measuring instruments
• EMC Testing

The eoProbe is a photoelectric field sensor that measures one axis based on electro-optical technology (the Pockels effect). This ultra-broadband sensor enables accurate measurements in almost any location and environment (air, liquid, gas, vacuum) under harsh conditions. The Kapteos system has achieved innovative electric field measurements through the electro-optical probe eoProbe and the high-end converter eoSense, utilizing this Pockels effect. Its measurement performance exceeds several MV/m and provides ultra-high bandwidth from 40 Hz to over 100 GHz, along with the most advanced features in extremely harsh environments such as underwater. <Comprehensive Measurement of Electric Field Vectors> The Pockels effect based on electro-optical technology allows for the measurement of the three components and phase of the vector electric field. Additionally, by using two types of probes—longitudinal and transverse—with the eoSensor converter, it is possible to accurately identify and measure the three-axis vector. <Non-Invasive Measurement> The active components of the sensor, which do not use metal parts, are essentially crystals. The measurement signal is transmitted by a laser within the fiber optic link. Electric field measurements inside animal tissues in MRI systems, as well as inside fruits or vegetables, are also possible.

• Optical Measuring Instruments
• EMC Testing
• probe

The SDS5000X series features Siglent's SPO technology with a maximum waveform capture rate of up to 110,000 wfm/s (up to 480,000 wfm/s in normal mode and sequence mode), a 256-level brightness grading display function, and a color temperature display mode. It also incorporates an innovative digital trigger system with high sensitivity and low jitter.

• oscilloscope

• Frequency range: 10KHz-11GHz • Laser power supply - no charging required • Extremely small size • High resolution, high speed, low noise • Electric field strength 0.1V/m-10kV/m • Wide dynamic range • Continuous real-time data streaming • PC computer interface & software included

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

.

• Other electronic measuring instruments
• oscilloscope

The Vector Signal Generator (Dual Channel Arbitrary Waveform Generator) SDG6000X, in addition to its function as an arbitrary waveform generator, is equipped with high-quality pulse generation capabilities, noise functions, IQ signals, selectable harmonics, PRBS, and other advantages. Other features include inter-channel phase locking, sweep/burst functions, channel tracking/coupling/replication, waveform overlay, and a built-in hardware frequency counter.

• Other electronic measuring instruments
• EMC Testing
• Signal Generator

A powerful and flexible tool for testing broadcast and RF devices. It offers reliable automated measurements and a wealth of features, including a tracking generator and multiple operating modes.

• Other electronic measuring instruments
• EMC Testing

The ICI 03 L-EFT set is a different set of three types of ICI sources: pulse magnetic field source, pulse electric field source, and pulse current source (FBBI). It enables very high precision and high-resolution IC analysis, and also allows for side-channel analysis, making it possible to test circuits that are critical for security. The features of the ICI 03 L-ET set include a probe tip with very high resolution (capable of testing very small areas) and a very low trigger for pulse jitter (destruction at specific points in a program sequence).

• EMC/Static electricity measuring equipment
• EMC Testing
• Other electronic measuring instruments

The world's top brand in "RF Safety," Wavecontrol, presents the portable electromagnetic field monitor, WaveMon, which continuously ensures the safety of workers operating in strong electromagnetic fields and surrounding areas. Weighing only 190g, this lightweight and compact monitor continuously monitors electromagnetic field exposure. 【Main Features】 - Equipped with a 3-axis electric and magnetic field sensor - Isotropic & RMS measurement - Relative value display design that is easy for the wearer to see - 6-level alarm with LED display, alarm sound, and vibration - Complies with international standards - ICNIRP, European Directive 2012/35/EU, FCC, SC6 relative values Designed with the user in mind, it is gaining popularity worldwide, especially in Europe. 1. Display design that is easy for the wearer to see 2. Includes arm belt 3. Ergonomic body design for easy grip 4. Compact at only 190g 5. Three types of alarm methods: LED, sound, vibration 6. GPS (optional)

• Data Logger
• EMC Testing
• Other environmental equipment

【Features】 - WiFi 2.45GHz frequency probe - Isotropic & true RMS measurement - High sensitivity 0.04V/m - High out-of-band attenuation - Electric field

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

【Features】 - Mobile frequency probe - Isotropic & true effective value measurement - High sensitivity 0.04V/m - High inter-band attenuation - Electric field measurement

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

New H-field broadband probe WPH1000 from Wavecontrol! High sensitivity of 0.018 A/m, isotropic RMS measurement, and compliant with international standards for magnetic field probe WPF1000. 【Main Features】 - High sensitivity - Isotropic & RMS measurement - Excellent attenuation - Compliant with international standards

• EMC Testing
• Strength Testing Equipment
• Other electronic measuring instruments

In the fields of medical electronics, automotive electronic components, power supply equipment, and mechanical engineering applications, high-resolution digital signal processing solutions are needed for small signal measurements and detailed signal recovery from large signals. Based on the X-Visual technology platform developed by Lilliput (OWON), the OWON XDS3000 n-in-1 on-site measurement station has been developed to meet these requirements. With three features—low background noise, a 40M record length, and a waveform refresh rate of 75,000 wfms/s—the performance of the XDS series products integrates data loggers, multimeters, waveform generators, DSO, etc., into a single device through a WiFi module that shares measurement data. This product is a "next-generation high-sensitivity n-in-1 portable digital oscilloscope" that leads a new trend in the next innovation of testing and measuring instruments.

• Other electronic measuring instruments
• oscilloscope