レイマック Product Lineup

As a characteristic of infrared light with a wavelength of 1100nm, it can pass through silicon materials. It also falls within the sensitivity range of CMOS cameras, allowing for transmission inspection without the need for expensive infrared-only cameras like InGaAs cameras. Please also consider the Infrared series and the Infrared3 series of long-wavelength infrared lighting. What is infrared light? We will introduce examples of circuit pattern inspection using infrared lighting. Infrared light has a longer wavelength than visible light (light visible to the human eye) and is not visible to the human eye. Compared to ultraviolet and visible light, infrared light has a very low scattering rate, resulting in a high transmission rate, allowing it to pass through liquids and inks. In particular, light with a wavelength of 1100nm has the characteristic of passing through silicon. Additionally, unlike halogen, the wavelength range is limited, so it does not affect photosensitive work.

• Lighting for image processing

The blending of light colors can be freely adjusted according to the inspection purpose. Red, blue, and green LEDs are integrated into a single lighting unit. With the combination of red, blue, and green wavelengths, it provides full-color visible light illumination, covering a very wide range of wavelengths. Since dimming can be independently controlled for each wavelength, subtle composite lighting colors are achievable.

• Lighting for image processing

The blending of light colors can be freely adjusted according to the inspection purpose. LEDs in red, white, blue, green, and infrared can be combined and implemented in a single lighting unit. By combining the three wavelengths of red, blue, and green, full-color visible light illumination is achieved, and adding infrared allows for a very wide range of wavelengths to be covered. Each wavelength can be dimmed independently, enabling subtle combinations of lighting colors. Various shapes can be manufactured according to your preferences, including direct dome shape, direct ring shape, low-angle ring shape, and direct bar shape.

• Lighting for image processing

The flight state of inkjet droplets can be imaged from a single droplet due to nanosecond light emission.

• Lighting for image processing

Up to 8 million lx!(※ ISSDBA-C90/20W,LWD=30mm) By combining with a dedicated controller, the steady-state light ratio is 137 to 16 times that of conventional strobe lights, and 3 to 25 times that of conventional strobe lights, compared with lighting of the same shape and approximate size. Super strobe lighting that makes maximum use of LED device specifications by original design using power LED. ※Cannot be used as constant lighting. Please use the dedicated controller IJS-SS series, ILS-SS series.

• Lighting for image processing

Compact and low-cost digital PWM controller By increasing the density of the implemented components and optimizing the design, we have achieved a compact size that is approximately 1/6 of the conventional size, making it the smallest in the industry for 30W 2CH. It features a highly visible digital display that allows for dimming with 1000 levels of gradation. The input voltage is DC24V, and the lineup includes the ILP-30M2 with an output voltage of DC12V and a total capacity of 30W, and the ILP-60M2-24 with an output voltage of DC24V and a total capacity of 60W.

• Other image-related equipment

The minimum output voltage has been expanded from 12V to 6V for the SAG2 series power supply, allowing output control from lower light levels. The emission time can be set in finer increments of 1μs compared to conventional products. Tool-free and easy connection with push-in connectors.

• Other image-related equipment

The GigE Vision Interface makes installation and operation as easy as a camera! This is the first lighting controller from a domestic manufacturer to support the general software interface standard GenICam. It allows control of other companies' cameras and lighting equipment using the same commands from applications compatible with GigE Vision/GenICam.

• Other image-related equipment

Power-free pulse and strobe (overdrive) dimming controller. Intelligent lighting realized through PoE (Power over Ethernet). By integrating control via Ethernet, the lighting system becomes more advanced. Not only does it enhance control flexibility, but it also supports advanced image processing applications, small-batch and diverse manufacturing, and streamlines system development and production, contributing to cost reduction as a total system. Dimming parameter control during variety switching is possible from a computer. By switching preset data using pattern data, it processes 8 patterns of dimming data at high speed. Ensures reproducibility and responsiveness in the performance of strobe (overdrive) lighting.

• Other image-related equipment

Two output voltage options (12 V DC, 24 V DC), three controller output power options (30 W, 50 W, 100 W), three channel options (2-channel, 4-channel, 8-channel), and three external control methods (TP, S2, PV)— a total of 42 models compatible with “AC 100–240 V input voltage,” as well as models with a 24 V DC output voltage, two controller output power ratings (50W, 150W), three channel configurations (2CH, 4CH, 8CH), and an external control method of LAN communication (TP), for a total of 3 models in the “DC 24V Input Voltage Compatible” series, and two output voltage options (DC 12V, DC 24V), a controller output capacity of 100W, 8 channels, and external control via LAN communication (TP)—a total of 2 models in the “High-Speed Synchronized Imaging System Compatible” series. This completes our full lineup of 47 models. You can select the optimal controller based on your lighting configuration and environment.

• Other image-related equipment

Dimming from 0 to 100% is possible with PWM control at approximately 80 kHz. It comes standard with an external ON/OFF control terminal. It supports an input voltage of AC 100 to 240V. *The standard included power cable is for AC 100V.

• Other image-related equipment

A constant-current dimming controller compatible with various external interfaces and capable of powering a wide range of lighting fixtures In addition to supporting connection with the IHV Series, IBF Series, IHVA-SP Series, and IHV-FX Series, other compact DC 12V-powered lighting fixtures can be connected to each CH　DC12V output connector. For external control, you can select from analog 0–5 V, 8-bit parallel, RS-232C, or LAN communication depending on the operating environment. By setting the maximum output current, you can simultaneously connect lighting fixtures designed for specific current control. The maximum output current can be set individually for each channel from 100 to 1,000 mA, allowing multiple lights to be turned on at the same time. The dimming range is adjustable in 256 steps from 0 mA up to the set maximum output current. *Lighting fixtures with a rated power of 1.2 W or less may trigger an error due to the automatic no-load detection function and may not be usable. The lineup includes four types compatible with various external control methods. External control options include 8-bit parallel, analog 0–5 V, RS-232C, and Ethernet. You can select the external control method that best suits your network environment.

• Other image-related equipment

A dedicated controller for the IDBC-LSRH/IDBB-LSRH series that allows individual output control in 100mm increments. Output control is available in 1,000 steps, enabling fine-tuning of uniformity on the lighting side. It is also possible to increase or decrease (offset) the overall output value while maintaining the illuminance balance set for each channel.

• Other image-related equipment

A high-performance constant-voltage controller ideal for line sensor illumination. Its variable output voltage makes it ideal for line sensor cameras and high-speed shutter cameras. The product lineup includes models powered by 24 V DC that can connect to lighting fixtures with power consumption of up to 300 W or 600 W, making them suitable for a wide variety of lighting applications. External output control can be switched between LAN and parallel communication using a switch.

• Other image-related equipment

High capacity controller ideal for line sensors and large surface illumination. Ideal for line sensor cameras and high-speed shutter cameras due to variable output voltage. The product range includes a digital type that can switch between LAN communication and parallel communication for external output control and an analog type of analog 0-5V.

• Other image-related equipment

This lineup has a total capacity of 30W with four channel choices of 2CH/3CH/4CH/6CH. It is more compact than the conventional SAG Controller. Dimming in 256 levels of 6V to set SAG value. There are four connection ports which can each be controlled with four computers. A larger current than regular lighting flows instantaneously. It can be used at up to approximately four times the current. Please consider the general-purpose type SAG2 series, LAN communication type SAG-TP series, large-capacity type SAG-HP series, and small DC24V input ILS series.

• Other image-related equipment

The overdrive setting (SAG value) can be adjusted in 256 steps from 10 V to 36 V. The output voltage can be controlled in 256 steps from 10 V up to the overdrive setting (SAG value). It features an internal control mode operated via switches on the front panel and an external control mode via LAN communication. It is equipped with four connection ports, allowing output settings to be configured from up to four computers. The trigger mode can be selected from internal trigger mode (fixed at 100 Hz) and external trigger mode. Overdrive Effect It can be connected to ISS series lighting fixtures, enabling illumination that is more than 16 times brighter than continuous light and more than three times brighter than conventional strobes.

• Other image-related equipment

Most of our standard LED illuminations can be stroboscopically triggered by an external trigger signal. Corresponding to the light emission time of 10μs-990μs by external trigger. Easy synchronization of light emission and camera exposure timing for high-speed mobile imaging applications. The LED element generates less heat, resulting in a longer life and stable light intensity. By releasing a larger current instantly, it can be used up to 4 times more than when used as constant lighting.* The maximum load varies depending on the illumination. Please consider the small IJS series dedicated to LAN control, and DC24V input compact ILS series.

• Other image-related equipment

Output voltage can be adjusted freely from a minimum of 10V to 36V. The compact body allows for easy storage within panels. The illumination time can be set in finer increments of 1μs compared to conventional products. The push-in connector requires no tools for easy connection.

• Other image-related equipment

Optimization of shooting timing: Synchronization control of lighting on/off, and trigger output to the camera is possible. Scalability: High flexibility allows for connection of units, enabling use of up to 40 channels. Lighting control: ON/OFF control of lighting is possible via LAN communication. Reduced wiring: Control of up to 40 channels is possible with a single LAN cable. Expanded lineup: Both base units and edge units are available in two types, 4-channel and 8-channel specifications, with two output voltage options of 12V and 24V, allowing for individual combinations of connections. Programming function: Control of multiple inspection stages is possible with a single trigger input for inspection timing. Space-saving design: Designed for installation in control panels using DIN rail mounting. Interface standards: Compatible with GigE Vision and GenICam (Generic Interface for Cameras).

• Other image-related equipment

It is possible to easily evaluate image synthesis algorithms represented by multiple imaging synchronized with the switching of the illumination direction and stereo with brightness differences. This is effective for tasks that are difficult with standard imaging, such as character inspection for glossy metals and resins, inspection of castings and patterned surfaces for engravings and dents, and detection of fine scratches. We provide hardware, software, and algorithms such as [split lighting], [controller], [I/O cable], and [sample program] all in one.

• Image Processing Equipment

The lighting can be easily and automatically controlled ON/OFF in conjunction with the camera's exposure time. It can be easily connected via I/O to cameras from various manufacturers such as Basler, Toshiba Teli, Omron Sentech, and FLIR. The 1-channel lighting control adapter, with a DC24V output and a maximum capacity of 36W, weighs about 40g, making it effective when combined with robots and other devices.

• Image Processing Equipment

Achieves 1.8 million lux with natural air cooling. *WD=50mm By using the app of the compatible controller, individual control every 100mm is possible from a computer. The light-emitting size is available up to 3,00mm in 100mm intervals. Compared to the conventional IDBB-LSRH series: - Brightness has improved by about 1.8 times in white comparison - Achieved approximately 30% weight reduction - Compact design with 3mm in the lighting height direction and 10mm in the lighting length direction - Unlike before, it is easy to add or replace various diffusion plates with different transmittance Since it is a natural air-cooled type, it can be used in environments such as clean rooms.

• Lighting for image processing

Achieving astonishing brightness High uniformity line lighting with compact size, power consumption, and weight The lineup includes the following four types. ● High intensity type　　 ： IDBC-LSRC series ● High intensity condensing type ： IDBC-LSRC-IL series ● High uniformity type　　 ： IDBC-LSRC-S series ● High uniformity condensing type ： IDBC-LSRC-S-IL series High intensity type is available in two colors, red and white, and high uniformity type is available in three colors, red, white, and blue. Size variations are lined up as High intensity type/High uniformity type is available in 100mm increments up to 2,000mm, High intensity condensing type/High uniformity condensing type is available in 100mm increments up to 1,000mm.

• Lighting for image processing

The new Briback Line Illumination is now even brighter! Compared to previous models, ・The IDBC-RE-H Series achieves 1.9 times (red) to 5.1 times (blue) higher luminance than the IDBB-RE Series ・The IDBC-RE series achieves 1.3 times (red) to 3.8 times (blue) higher luminance compared to the IDBB-RE-S series (WD=50mm) Available in white, red, and blue; lighting lengths can be selected in 100mm increments up to a maximum of 1,800mm.

• Lighting for image processing

8-Channel Segmented Lighting with Low-Angle Direct Ring Illumination. Even for workpieces prone to glare, it is possible to capture images with reduced glare by individually illuminating them from eight directions and then combining the resulting images. It is also ideal for visual inspection of workpieces with uneven surfaces.

• Lighting for image processing

8-channel split lighting with a horizontal orientation. By individually illuminating workpieces prone to halation from 8 directions and synthesizing the resulting images, it is possible to capture images while suppressing halation. It is also ideal for the appearance inspection of uneven workpieces.

• Lighting for image processing

Reimac will sell SmartVisionLights products from the American company "SmartVisionLights" as their Japanese distributor. SmartVisionLights (hereinafter referred to as SVL) is a company that develops products primarily focused on high-speed/high-output lighting for logistics. ■ Unique Features of SVL, Built-in Controller ・ "DUAL OVERDRIVE" DUAL OVERDRIVE is a feature that combines two OVERDRIVE functions, allowing for more powerful light emission in a shorter time. ・ "HIDDEN STROBE" The bright lighting from OVERDRIVE may require measures against glare (such as the use of light shields or invisible light) for people near the lighting, but this feature eliminates that need. SVL has received the "inVISION TOP Innovation 2024" award for this technology. ・ Built-in Controller The lighting has a built-in controller, making it easy to use the above features simply by wiring the camera and lighting together.

• Lighting for image processing

When adopting segmented lighting, the wiring tends to increase in proportion to the number of lighting channels, but this product achieves significant wiring reduction. 1. Achieves overwhelming wiring reduction: The configuration allows the cables for the robotic arm to be managed with "only one LAN cable." 2. Compatible with any industrial camera: There is no need to purchase cameras from specific manufacturers; existing cameras can be used. 3. Synchronized lighting can be achieved with just camera settings: Since the lighting has a controller (control device) built-in, complex programming is unnecessary.

• Lighting for image processing

Constant voltage controller with external 0-5V control function. The IMAR series, IDHM series, IFVA series, and IFHA series are variable constant voltage output controllers that can be easily connected and operated. Equipped with external ON/OFF and external 0-5V control functions.

• Other lighting equipment