篠原電機 List of Products and Services

The "Card Holder (Adhesive Fixed Type with Screw Combination)" has a strong double-sided adhesive tape applied to the back, providing very strong adhesion and eliminating the need for drilling holes and tapping. It does not corrode the adhesive surface. It is resistant to temperature and humidity, and can easily adapt to slightly rough surfaces while also allowing for screw installation. 【Features】 ■ Strong adhesion due to the double-sided adhesive tape on the back ■ Eliminates the need for drilling holes and tapping ■ Does not corrode the adhesive surface ■ Resistant to temperature and humidity, and can easily adapt to slightly rough surfaces while allowing for screw installation *For more details, please refer to the PDF document or feel free to contact us.

• others

The "SS Bushing" can be used as an introduction bushing for the lock shaft that opens and closes the doors of distribution boards and similar equipment. 【Features】 1. When locking the door, the taper of the "bushing" smoothly guides the shaft into the lock hole. 2. It prevents noise caused by vibrations. 3. It eliminates paint peeling around the lock hole due to the opening and closing of the lock shaft, preventing rust formation. 4. The installation of the SS bushing can be done with a simple push, making it a one-touch operation. *For more details, please refer to the PDF document or feel free to contact us.

• Control Panel

The "Bracket for Mounting Protection Plates" can be used as a bracket (suspension device) for mounting protection plates (charging area protection barriers) inside cubicles and similar enclosures. 【Features】 1. The protection plate can be suspended, eliminating the need for troublesome processing such as daruma holes. 2. Since it is a suspension type, there is no need for complicated screw processing like tapping on the panel side. (It can be attached with a single touch.) 3. Installation and removal are easy, improving work efficiency and reducing maintenance time for inspections and cleaning. 4. No mounting screws are required, so there is no worry about losing screws during work, allowing for safe operations. 5. Products with insulated protection plates (barrier plates) can also be manufactured. Please specify the dimensions. *For more details, please refer to the PDF materials or feel free to contact us.

• Control Panel

The "Hook Stick Display Label" is a label that can be used to indicate storage on a panel equipped with a hook stick for operating circuit breakers. It has been laminated, making it suitable for outdoor use. The base paper is transparent PET, so it blends well with the panel's paint color. It is based on the "Guidelines for Certification of Cubicle-Type Emergency Power Supply Receiving Equipment" published by the Japan Electric Association. 【Features】 ■ Display label based on the "Guidelines for Certification of Cubicle-Type Emergency Power Supply Receiving Equipment" published by the Japan Electric Association ■ Laminated for outdoor use ■ The base paper is transparent PET, ensuring no discomfort with the panel's paint color *For more details, please refer to the PDF document or feel free to contact us.

• Control Panel

We also offer a "holder and tray for hook rods" that can be used for the opening and closing operation of electrical circuit breakers. 【Features】 ■ For hook rods used in the opening and closing operation of electrical circuit breakers ■ Environmentally friendly, electro-galvanized trivalent chromate treatment *For more details, please refer to the PDF document or feel free to contact us.

• Control Panel

The "Disconnect Switch Hook Rod (Hook Rod for Operating Disconnect Switches)" can be used for opening and closing operations of electrical circuit disconnect switches. 【Features】 1. Complies with JIS-C-4510 standards. 2. Made of plastic, it has excellent insulation properties and is non-absorbent. 3. Lightweight and easy to operate. 4. Uses a danger color yellow pipe. 5. With a pipe diameter of 32mm, it has excellent strength. * The FBK type has a longer hook section, making it easier not only to open and close the disconnect switch but also to operate the cutout. * For more details, please refer to the PDF document or feel free to contact us.

• Control Panel

"Decorative screws" can be used for distribution and control panels, etc. *For more details, please refer to the PDF document or feel free to contact us.

• Control Panel

The "Parts Box" is a storage box for spare parts used in equipment such as distribution boards, control panels, and operation panels. Made of transparent plastic, the contents can be seen from the outside. The opening and closing mechanism is one-touch, making it easy to access spare parts. It becomes even more convenient when used in combination with a drawing holder. It can be attached with double-sided adhesive tape and can also be secured with screws. It is lightweight and there is no worry about it breaking. 【Features】 ■ Transparent plastic allows visibility of contents from the outside ■ One-touch opening and closing makes it easy to access spare parts ■ Can be attached with double-sided adhesive tape and secured with screws ■ Lightweight with no risk of breaking *For more details, please refer to the PDF document or feel free to contact us.

• Storage

【Features】 1. The earth wire is built into the plastic pipe, providing excellent insulation and safety. 2. The earth wire and clips at the bottom of the pipe are covered with an insulating tube, allowing for safe use. 3. It is lightweight and easy to operate. 4. The pipe is made of a hazardous color, yellow. *For more details, please refer to the PDF document or feel free to contact us.

• others

【Features】 ■Made to order (e.g., AT-200 × 5 units) *For more details, please refer to the PDF document or feel free to contact us.

• Other terminal blocks

The "Low Voltage Branch Terminal Block" is a terminal block that can connect up to 7 branches as a low voltage branch terminal block. It has an insulation voltage of 2.5kV and a creepage distance of more than 20mm. 【Features】 ■ Can connect up to 7 branches as a low voltage branch terminal block (for 200A) ■ Insulation voltage of 2.5kV ■ Creepage distance of more than 20mm *For more details, please refer to the PDF document or feel free to contact us.

• Other terminal blocks

The "Stud Terminal Block" is a terminal block that can be used as a junction, branch, or support for wires, copper busbars, etc. Without changing the dimensions of the main body, there are three types of screw diameters: M6, M8, and M10. It has excellent insulation properties, is lightweight, and does not break. 【Features】 ■ Choose from three types of screw diameters: M6, M8, and M10 without changing the dimensions of the main body ■ Excellent insulation properties, lightweight, and unbreakable ■ Green type also available for the main body ■ RoHS compliant *For more details, please refer to the PDF document or feel free to contact us.

• Other terminal blocks
• Terminal Blocks

The "Ground Terminal Panel" is a ground terminal panel based on the "Guidelines for Certification of Cubicle-Type Emergency Power Supply Receiving Equipment" issued by the Japan Electric Association. We use our ground terminal blocks AT-50/100/200. Depending on the application, you can choose from six combinations regarding the number of ground terminal blocks, the presence of separators, and the presence of test terminals. 【Features】 ■ For certified cubicles ■ Uses ground terminal blocks "AT-50/100/200" ■ Choose from six combinations based on application *For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic parts

The "Back Wiring Type Ground Terminal Block" is a terminal block that allows for easy wiring when using rear-wired devices. By opening the movable bar, it is possible to easily measure the resistance on the ground electrode side. Additionally, by short-circuiting each of the T1, T2, and T3 terminals, the resistance on the ground electrode side can be easily measured. 【Features】 ■ Easy wiring when using rear-wired devices ■ Easy measurement of resistance on the ground electrode side by opening the movable bar ■ Easy measurement of resistance on the ground electrode side by short-circuiting each of the T1, T2, and T3 terminals *For more details, please refer to the PDF document or feel free to contact us.

• Other terminal blocks

The "ground terminal block" is a terminal block that allows for easy measurement of the resistance on the grounding side by opening the movable bar. By short-circuiting the EA, EB, and ED terminals, the resistance on the grounding side can be easily measured. There is also a type with a two-tier movable bar (AT-200W) available for use according to your conditions. 【Features】 ■ Easy measurement of the resistance on the grounding side by opening the movable bar ■ Easy measurement of the resistance on the grounding side by short-circuiting the EA, EB, and ED terminals ■ A type with a two-tier movable bar (AT-200W) is also available in the lineup ■ The base is available in black and green types *For more details, please refer to the PDF document or feel free to contact us.

• Other terminal blocks

Since the copper plate and steel plate are brazed together, they will not come apart due to the heat from welding. We offer a variety of options from one hole to four holes, rated for a current of up to 400A. Additionally, the "ECK type" is convenient for use in narrow areas where it is difficult to tighten bolts, such as corner sections. 【Features】 ■ Complies with Ministry of Land, Infrastructure, Transport and Tourism standards ■ Brazed copper and steel plates do not come apart due to welding heat ■ Various options available from one hole to four holes, rated for a current of up to 400A *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "surface heater" is a surface heating element with a patterned nickel alloy resistor arranged between silicone rubber sheets. The outer layer is reinforced with glass cloth, providing excellent mechanical strength. High-efficiency far-infrared radiation is emitted from the surface, making it suitable for far-infrared heating of polymer materials. Compared to conventional ceramic far-infrared radiators, it is lighter, softer, and lower in cost. 【Features (Silicone Rubber Heater)】 ■ Shapes and patterns can be freely designed and manufactured according to application ■ Fits heated surfaces such as curved and cylindrical shapes ■ Excellent thermal responsiveness and rapid heating capability *For more details, please refer to the PDF materials or feel free to contact us.

• Board materials

The "Thermostat PTSC-090S" can be used for temperature control (turning the power on and off) of space heaters, ventilation fans, and more. It can be mounted on a DIN rail (it can be installed at the center of the thermostat body). In addition, we also offer the "TS-120S," which allows for continuous and stepless temperature adjustment from 0 to 120°C using a dial, and the "ITS-050L." *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Space Heater" is a product that can be installed inside various panels to prevent condensation and humidity. It can also be used as a heating device or an open duct heater for drying purposes. The heating element is fixed by wrapping electric heating alloy wire around a mica plate, which is then sealed with either zinc-coated steel plate (chrome-free) or stainless steel plate. 【Features】 ■ Prevents condensation and humidity inside various panels ■ Heating element is fixed by wrapping electric heating alloy wire around a mica plate ■ Sealed with zinc-coated steel plate (chrome-free) or stainless steel plate *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "SSH Type and TSSH Type Space Heater Specifications" are equipped with a heat dissipation cover attached to the space heater, which can be used to prevent condensation and reduce humidity inside the panel. By using the space heater, the total length is shortened by only 200W, allowing for space-saving solutions. This product incorporates a space heater into a heat dissipation cover made of punched steel plate, making it easy to install with four screws. 【Features】 ■ Shortened total length for space-saving solutions ■ Space heater integrated into a punched steel plate heat dissipation cover ■ Easy installation with four screws *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

【Features】 1. The space heater (terminal block type) that has been loved for years has been significantly downsized! It is suitable for compact control panels and operation panels. 2. It also contributes to space-saving in various other panels. 3. It comes with a cover made of punched steel plate to prevent any risk of direct contact with the heat source. 4. It is equipped with a terminal block as standard, making it easy to connect power lines. *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

It can be used as a heater to prevent condensation and reduce humidity inside the panel. A terminal block is incorporated into the wire connection part, making work easy. 【Features】 ■ Heater for preventing condensation and reducing humidity inside the panel ■ Terminal block incorporated into the wire connection part ■ Easy to work with ■ Terminal block: Rated 600V/25A, made of polycarbonate *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Space Heater with Heat Dissipation Cover" is a space heater equipped with a heat dissipation cover, designed for use to prevent condensation and humidity inside the panel. It is made by incorporating a space heater into a heat dissipation cover made of punched steel plate, allowing for easy installation with two or four screws. It is designed and manufactured to be extremely safe, ensuring that there is no risk of direct contact with the heat source. 【Features】 ■ Incorporates a space heater into the heat dissipation cover ■ Easy to install ■ Safe design that prevents direct contact with the heat source *For more details, please refer to the PDF materials or feel free to contact us.

• Board materials

【Features】 1. The grip section is designed with curves to fit comfortably in the hand when held. 2. It has a height that accommodates four fingers of an average adult male, making it very easy to grip. *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

【Features】 ■ The resin cover has a magnet attached, making installation and removal easy. SWCK-90 (Compact Type) 1. The resin cover has a magnet attached, making installation and removal easy. 2. It is almost the same size as the conventional model (SWC-90), but the coverage area has been expanded. 3. The adhesion strength of the neodymium magnet reduces the likelihood of the cover shifting or falling off due to accidental contact. 4. Each side has a 30mm wide notch, allowing it to bypass simulated busbars. SWC-60 The height has been reduced compared to the conventional model, making it suitable for cam switches with a depth of 50mm. SWC-74K 1. The resin cover has a magnetic catch attached, making installation and removal easy. 2. It has been made more compact compared to the conventional model and is sized to fit approximately 55mm square escutcheons. 3. A push-in spacer can be installed in the center, helping to prevent forgetting to push it in after pulling the handle. *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Push Button Cover Mounting Base" is a product used as an attachment when you want to install our push button cover "SWC-88" on a non-magnetic housing such as SUS304. Since it is installed by being fastened together with the equipment, no additional processing is required. We offer three types of hole diameters to match the size of the button. The area between the bracket and the panel surface is protected by an acrylic plate, so the magnet of the bracket and the push button cover does not come into direct contact with the panel surface. It protects not only non-magnetic housings but also existing panels and painted surfaces of steel panels from scratches. 【Features】 ■ The bracket is made of ferrite stainless steel (SUS430) ■ No additional processing is required as it is installed by being fastened together with the equipment ■ Three types of hole diameters are available to match the size of the button ■ The area between the bracket and the panel surface is protected by an acrylic plate *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

It can be used as a cover to prevent accidental operation of push buttons and operation switches. The resin cover comes with a magnet, making it easy to attach and detach. 【Features】 ■ Cover to prevent accidental operation of push buttons and operation switches ■ Comes with a magnet on the resin cover ■ Easy to attach and detach *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Drawing Bag" can be used as a storage bag to keep drawings and specifications for distribution boards, cubicles, control panels, operation panels, etc., within the panel. It is suitable for storage as it is transparent and allows for easy visibility of the contents, and it also has an excellent aesthetic appearance. The buckle design makes it easy to open and close. The top cover helps prevent dust and other contaminants. Additionally, it comes with a spare card holder, which can be used for the administrator's business cards. 【Features】 ■ Transparent for easy visibility of contents ■ Excellent aesthetic appearance ■ Easy to open and close due to the buckle design ■ Top cover prevents dust and other contaminants ■ Includes a spare card holder *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Drawing Holder" can be used to store drawings and specifications for distribution boards, cubicles, control panels, operation panels, etc., within the panel. It is suitable for storage as it is transparent and allows for easy visibility of the contents, and it also has excellent aesthetics. It is lightweight and safe, with no risk of breaking, making it easy to handle. Installation is simple as it can be attached with double-sided adhesive tape. Additionally, there are guide holes for screws, allowing for screw fastening as well. 【Features】 ■ Transparent and allows for easy visibility of contents ■ Excellent aesthetics ■ Safe and easy to handle ■ Easy installation with double-sided adhesive tape ■ Screw fastening is also possible *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "One-Touch Terminal Cover DLSC-1" can be used as a terminal protection cover for limit switches (panel-mounted type). It does not require mounting screws and can be attached and detached with one touch, providing excellent workability and maintainability. There is a hole on the back side for tester probes, allowing for wiring checks while the cover is attached. Additionally, we also offer the ABC part "DSK-85," which is suitable for mounting limit switches. 【Features】 ■ No mounting screws required; can be attached and detached with one touch ■ Excellent workability and maintainability ■ Wiring checks can be performed while the cover is attached *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Cable Entry Clamp" is a product used to support electrical wires at the cable entry points of various panels. The work is completed simply by sandwiching the wire inserted from the entry point with a packing and securing the main body to the enclosure with screws. Since there is no need to use filling materials as in the past, work efficiency is improved. The new compact and simple structure product "Cable Entry Clamp (DK-SE-10)" can also be used for wire introduction. 【Features】 ■ Easy wire support ■ Wide cable entry for excellent workability ■ No need to use filling materials as in the past ■ Improved work efficiency ■ Prevents the intrusion of dust and debris from the outside *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Small Door with Window Frame IP55: MD-AY-2020KT (Made to Order)" is used as a small door for operation in control panels, operation panels, cubicles, etc. 【Features】 1. It combines a small door for operation with a window frame, allowing visibility of internal instruments and operation of internal devices without opening the main door of the panel. 2. Installation is easy. It can be fitted into the panel hole from the front and secured with a backing frame and nuts from the back. 3. There is no need to weld to the panel door, which prevents warping of the door and improves work efficiency. 4. It can also be used for outdoor panels. (IP55) 5. Custom sizes can be ordered. Please consult us. *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Blank Panel" is a product used for cutting spare panels for various meters and equipment, as well as for covering unnecessary panel cuts. It is sized to fit meters from various manufacturers. The material is made of steel plate and finished with black paint. 【Features】 Sized to fit meters from various manufacturers. *For more details, please refer to the PDF document or feel free to contact us.*

• Board materials

The "Resin (PP) Instrument Window Frame (PY Type) IP55" has excellent weather resistance and a beautiful finish, enhancing the value of the product. It is easy to install; simply drill a hole of the cut dimensions in the panel, insert the instrument window frame from the front, and secure it with screws from the back using the included parts. Due to its waterproof structure, it can be used for outdoor applications. Additionally, we also offer PVC instrument window frames for indoor use. 【Features】 ■ Resin material: PP, PVC ■ Easy installation ■ Waterproof structure IP55 (PY Type) ■ Excellent weather resistance and beautiful finish *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Steel Plate Instrument Window Frame (SN Type) IP55" is excellent in weather resistance and aesthetics, enhancing the value of the installed products. It is lightweight and easy to install, which improves work efficiency. We offer two types: steel plate and stainless steel, so you can choose according to your application. 【Features】 ■ Lightweight ■ Easy to install ■ Improved work efficiency ■ Available in steel plate or stainless steel ■ IP55 *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Rubber Instrument Window Frame (MG Type) IP54" is an easy-to-install window frame that improves work efficiency. It is a round type with a panel cut size of φ133. We offer both wire mesh and reinforced types of window glass. 【Features】 ■ Easy to install ■ Improved work efficiency ■ Round type ■ Panel cut size: φ133 ■ IP54 *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Rubber Window Frame (GMY Type) IP55" is a product used for reading and confirming windows in receiving panels, distribution panels, control panels, instrument panels, etc. Installation is extremely simple, and there is no need to use a retaining frame as in the past. The rubber window frame is fitted into the panel cut from the front and can be installed by simply securing it with screws from the back. Additionally, since there are no seams in the main body of the window frame, there are no restrictions on the installation direction. It has a waterproof structure, making it suitable for outdoor use as well. 【Features】 ■ High cost-performance rubber molded product ■ Extremely easy to install ■ No retaining frame required as in the past ■ No restrictions on installation direction (no distinction between vertical and horizontal) ■ Usable for outdoor applications due to waterproof structure (IP55) *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "stainless steel window frame" is a product used for inspection windows in receiving panels, distribution panels, control panels, instrument panels, etc. Installation is extremely simple; you can fit the window frame into the panel hole from the front and secure it with a backing frame and nuts from the back. Being made of stainless steel, it has excellent corrosion resistance. It features a waterproof structure, making it suitable for outdoor use. We can also produce UV-cut film specifications and wired glass (6.8mm) specifications. We accept orders for special sizes, so please feel free to consult with us. 【Features】 ■ Extremely easy to install ■ Excellent corrosion resistance due to stainless steel construction ■ Waterproof structure allows for outdoor use (IP55) ■ Production of UV-cut film specifications is also possible ■ Wired glass (6.8mm) specifications can also be produced ■ Orders for special sizes are also possible *For more details, please refer to the PDF materials or feel free to contact us.

• Board materials

"PET sound-absorbing material" is a safe product that does not cause discomfort to workers and is easy to recycle, even when burned. It has high heat resistance and flame retardancy, equivalent to UL94 HBF. It is intermediate between GW and polyurethane foam, with strong resistance to ultraviolet rays and hydrolysis. Additionally, it can be manufactured in any size. 【Features】 ■ Environmentally friendly ■ High heat resistance and flame retardancy ■ Strong resistance to ultraviolet rays and hydrolysis ■ Can be manufactured in any size *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "CNP Filter" is a product that employs a micro demister made from long fibers of several tens of micrometers, which are carved from stainless steel foil using a special cutting method, needle punched, and compressed with rollers. Additionally, by using all stainless steel materials, it possesses ultra-high temperature resistance, chemical resistance, and corrosion resistance, while achieving high efficiency and high oil retention due to its fiber diameter and porosity. As media, we have prepared three types: a standard type with a fiber diameter of 25μm, a density gradient type (standard) combining fiber diameters of 50μm and 25μm, and a density gradient type (high performance) combining fiber diameters of 50μm and 10μm. 【Features】 ■ Usable in high-temperature environments (heat resistance up to 480℃) ■ Excellent corrosion resistance ■ Achieves high efficiency by lowering porosity through compression ■ Minimizes fiber shedding during use or cleaning *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

【Features】 A low-pressure loss type utilizing a paper honeycomb core as a spacer. GG … Activated carbon with suitable adsorption strength and particle size can be selected based on the type and concentration of the gas to be adsorbed. T-B … Excellent for the removal of basic gases such as ammonia and trimethylamine. G-H … Excellent for the removal of acidic gases such as hydrogen sulfide and mercaptans. AD (TF) … Effective for the removal of acetaldehyde and formaldehyde. *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Shield Filter (Electromagnetic Wave Prevention Filter)" is a product used as an air filter and ventilation panel that has electromagnetic wave prevention effects. It is designed in a cassette type, making installation and removal easy. Since it is made entirely of aluminum, it is lightweight and has excellent corrosion resistance and durability. Additionally, it can be cleaned with air brushing or washing, allowing for optimal maintenance of filter performance. 【Features】 ■ Electromagnetic wave prevention effect ■ Easy installation and removal with cassette type ■ Lightweight due to the use of all aluminum materials ■ Excellent corrosion resistance and durability ■ Can be cleaned with air brushing or washing *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

The "Cassette Filter CSF Type" is a dust-proof filter for ventilation areas such as distribution boards and control panels. Since it is in a cassette form, it can be easily installed and removed. Additionally, the filter frame is made of aluminum, making it lightweight, rust-free, and washable. 【Features】 ■ Its cassette design allows for easy installation and removal. ■ The aluminum frame makes it lightweight, rust-free, and washable. *For more details, please refer to the PDF document or feel free to contact us.

• Board materials

Shinohara Electric Co., Ltd.'s "Air Filters" come in a wide variety of types according to usage conditions, and sizes can also be specified as desired. Orders for cassette types (custom sizes, aluminum filter frames) are also possible. 【Main Features of the Filters】 【Firedon】 This is a non-directional fiber aggregate air filter with low pressure loss and high dust collection capacity, which is non-flammable and unaffected by humidity (compliant with JIS L-1091 category 3). There are also types that can be regenerated through washing. 【Malt Filter】 Due to the freedom to choose density (number of cells, 8 to 50 per 25mm) and thickness (5 to 30mm) based on application, it is ideal for commercial packages, etc. It is relatively easy to regenerate through washing. 【Saran Honeycomb】 This filter is woven from Saran fibers in a screen-like structure, making it optimal for outlet and fan coil filters. It has excellent washability and is easy to regenerate due to its lack of water absorption and moisture retention. *For more details, please refer to the PDF materials or feel free to contact us.*

• Board materials

The "Plastic Gallery GPC Series" is a ventilation opening component for control panels and communication panels. It can be easily attached to the panel opening with a single touch, improving work efficiency. Additionally, it can be continuously installed in both vertical and horizontal directions, enhancing aesthetics and increasing the product value of the panel. We also offer types that can be attached to round hole panel cuts and front-opening plastic galleries. 【Features】 - Can be attached to the panel opening with a single touch - Can be continuously installed in both vertical and horizontal directions - Excellent aesthetics, enhancing the product value of the panel - Easy filter replacement by removing the front gallery - Compatible with 92mm, 120mm, and 160mm fans *For more details, please refer to the PDF document or feel free to contact us.

• Board materials