FIRSTEC CORPORATION Product Lineup

It can be used for marking work and processing with milling machines and drill presses.

• byte

It can be used for marking work and processing with milling machines and drill presses.

• byte

● With fine adjustment mechanism ● Block gauge is not included

• byte

The block gauge is not included.

• byte

The block gauge is not included.

• byte

It can be used for marking work and processing with milling machines and drill presses.

• byte

● The setting of worms with the same shape can be done reliably in a short time. ● The stepped stop pin allows for setting in the groove of the workpiece.

• byte

● It is used when attaching and detaching tools. ● Please use it fixed to a workbench or similar.

• byte

● It is used when attaching and detaching tools. ● Please use it fixed to a workbench or similar.

• byte

● It is used when attaching or detaching tools. ● Please use it fixed to a workbench or similar.

• byte

The accuracy when placed side by side is ±0.005mm, and the accuracy for each size is ±0.01mm, making it a low-cost Taiwanese tool with quality comparable to Japanese products.

• byte

The accuracy when placed side by side is ±0.005mm, and the accuracy for each size is ±0.01mm, making it a low-cost Taiwanese tool with quality comparable to Japanese products.

• byte

The accuracy when placed side by side is ±0.005mm, and the accuracy for each size is ±0.01mm, making it a low-cost Taiwanese tool with quality comparable to Japanese products.

• byte

The accuracy when placed side by side is ±0.005mm, and the accuracy for each size is ±0.01mm, making it a low-cost Taiwanese tool with quality comparable to Japanese products.

• byte

●With through hole for oil hole (with set screw inside) ●With ER collet nut

• byte

●With through hole for oil hole (with set screw inside) ●With ER collet nut

• byte

●With through hole for oil hole (with set screw inside) ●With ER collet nut

• byte

●With through hole for oil hole (with set screw inside) ●With ER collet nut

• byte

●With through hole for oil hole (with set screw inside) ●With ER collet nut

• byte

Collet nut for FT-S16-ER11-100

• byte

Collet nut for FT-S20-ER16-100 and FT-S20-ER16-150.

• byte

Collet nut for FT-S20-ER20-100 and FT-S20-ER20-150.

• byte

Collet wrench for FT-S16-ER11-100

• byte

Collet wrench for FT-S20-ER16-100 and FT-S20-ER16-150.

• byte

Collet wrench for FT-S20-ER20-100 and FT-S20-ER20-150.

• byte

●It is easy to tighten the drill by hand. A wrench for tightening is also included as standard.

• byte

Attach the touchpoint sensor to the spindle and measure by slowly bringing the workpiece closer while rotating the touchpoint sensor at about 450-600mm.

• byte

Attach the touch point sensor to the spindle and perform the measurement by slowly bringing the workpiece closer while rotating the touch point sensor at approximately 450-600mm.

• byte

Attach the touchpoint sensor to the spindle and perform the measurement by slowly bringing the workpiece closer while rotating the touchpoint sensor at around 450-600mm.

• byte

● Attach the touch point sensor to the spindle and perform measurements by slowly bringing the workpiece closer while rotating the touch point sensor at about 450-600mm. ● Features: Ceramic tip.

• byte

● Attach the touchpoint sensor to the spindle and perform measurements by slowly bringing the workpiece closer while rotating the touchpoint sensor at about 450-600mm. ● Features: Ceramic tip.

• byte

● Attach the touch point sensor to the spindle and perform measurements by slowly bringing the workpiece closer while rotating the touch point sensor at approximately 450-600mm. ● Features: Ceramic tip.

• byte

●There is no magnet on the bottom surface. ●Bottom diameter: 68mm

• byte

● Height from the base: 50mm (±0.005mm) ● With base magnet ● Battery used: LR44 x 2 (included)

• byte

●Easy to calibrate with a parallel or gauge block ●Equipped with a bottom magnet

• byte

●Easy to calibrate with a parallel or gauge block ●Equipped with a bottom magnet

• byte

The dial gauge, magnetic stand, and pin gauge are not included.

• byte

The dial gauge, magnetic stand, and pin gauge are not included.

• byte

The dial gauge, magnetic stand, and pin gauge are not included.

• byte

Applicable to micrometers up to 100mm.

• byte

It is convenient when using three-dimensional measuring machines, projectors, tool microscopes, and magnifying glasses.

• byte

● The base plate is detachable. ● It tightens simply by rotating the chuck, so no handle is needed. ● Made of durable steel. ● Compatible with both inner and outer jaws. ● The minimum gripping diameter is 0.8mm. ● The base plate is detachable. You can remove the base plate and attach it to other measuring fixtures.

• byte

● The base plate is detachable. ● It tightens simply by rotating the chuck, so no handle is needed. ● Made of durable steel. ● Compatible with both inner and outer jaws. ● The base plate is detachable. You can remove the base plate and attach it to other measuring fixtures.

• byte

● The base plate is detachable. ● It tightens simply by rotating the chuck, so no handle is needed. ● Made of durable steel. ● Compatible with both internal and external jaws. ● The base plate is detachable. You can remove the base plate and attach it to other measuring fixtures.

• byte

● The base plate is detachable. ● It tightens simply by rotating the chuck, so no handle is needed. ● Made of durable steel. ● Compatible with both inner and outer jaws. ● The base plate is detachable. You can remove the base plate and attach it to other measuring fixtures.

• byte