Notice of Discontinuation of Sales for Sonaer Particle Generators

Spraying fine particles without pressure! Atomization through the vibration of piezoelectric ceramics!! Low power consumption and low energy costs!!

Ultrasonic waves generated by piezoelectric ceramics are transmitted to the spray nozzle (atomizer), where they vibrate the liquid film to create extremely fine particles for spraying. Liquid can be supplied and sprayed into fine particles without the need for pressurization. The flow rate varies depending on the model, but it can accommodate a wide range from a minimum flow rate of 10 ml/min to a maximum of 100 ml/min. Since pressure is not applied to the liquid, there is very little splatter or rebound, eliminating waste of the applied liquid. Additionally, there is no need for a large painting booth. This achieves a reduction in capital investment and running costs. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia Corporation.

• Ultrasonic Oscillator
• nozzle
• valve

Designed for fluids that have a strong impact on stainless steel, such as pharmaceutical-related applications.

The Sonia Corporation's PTFE fluoropolymer microfeed tube is designed specifically for fluids that have a strong impact on stainless steel, particularly for pharmaceutical-related applications. The liquid must be completely isolated for reasons of hygiene and chemical reactions. *This product is an accessory specifically for Sonia Corporation's ultrasonic spray nozzle.

• nozzle
• Water Hydraulic Equipment
• others

It precisely sprays fine particles!

The pinpoint air transport fixture generates high-quality, fine particles and can uniformly apply them to medical coatings and other small precision devices. The spray speed is slow, making it suitable for applying expensive chemicals in a thin layer with minimal use. It excels not only in coating and manufacturing applications for medical precision instruments but also in uses such as stent coating and catheter coating, providing excellent reproducibility of spray speed and particle diameter, while significantly reducing the consumption of the coating agent. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia Corporation.*

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

A fixture for applying particles sprayed from an ultrasonic spray nozzle over a wide area.

The wide-angle air transport fixture is a device that uses gas or air to expand the spray angle. The wide-angle air transport fixture can be attached to the Narrow Spray models 60K50T and 130K50T. There is an air supply port on the side of the wide-angle air transport fixture. By injecting gas or air, the gas or air circulates inside, causing the particles sprayed from the ultrasonic spray nozzle to spread and be pushed out. By adjusting the gas volume, air volume, pressure, and the tip of the ultrasonic spray nozzle, a spray angle of up to approximately 100° can be achieved. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia.

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

A fixture for spreading wider than a wide-angle air transport fixture.

Dove Tail Spray Shaper The Dove Tail Spray Shaper is an air transport fixture, ideal for wide-angle spraying and flux coating. It can be used with all spray nozzles of NS and WS types. By changing the position of the Dove Tail Spray Shaper, it is possible to switch from a fan-shaped spray pattern to an elliptical spray pattern. *This product is a dedicated accessory for the ultrasonic spray nozzles manufactured by Sonia Corporation.

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

It is a subcutaneous solvent delivery device that can coat evenly and thinly.

Sonia's hypodermic needle spray attachment allows for precise and uniform thin coating, generating high-quality fine particles in a relatively narrow range. It is suitable not only for improving biocompatibility and drug delivery but also for preventing restenosis and thrombosis. It prevents clogging, provides uniform film thickness and density with low-speed application, and reduces wasteful coating. *This product is a dedicated accessory for Sonia's ultrasonic spray nozzle.*

• Ultrasonic Oscillator
• nozzle
• spray

Flow spray of 2 mmlit/min or less is possible!

Sonaer low-flow spray nozzle manufactured by Sonia Co. It can focus on small parts without waste by creating micron and sub-micron particles. There are two types of nozzles: flat and wide spray tips. These nozzles are ideal for pinpoint spray shaping, focusing particles and minimizing solution waste. With these nozzles, coating control becomes possible, easily adapting to applications that require thin and uniform application. This nozzle is lightweight, making it attractive for use in robotic coating systems. The nozzle comes in a lightweight black aluminum case (custom-made) or a stainless steel case with a stainless steel inner feed tube. The micro feed tube can be used for microliter capacities and is available in stainless steel and PTFE. The nozzle can utilize a spray shaper for pinpoint spraying, allowing for better control of your coating applications.

• nozzle
• valve
• Etching Equipment

A new challenge with the Sonia Corporation's low-flow ultrasonic spray nozzle!

Low Flow Ultrasonic Spray Nozzle (Atomizer) The low flow spray nozzle (atomizer) manufactured by Sonia is designed to apply droplets (particles) of various viscosities in micron and submicron sizes without over-applying them to small parts. The nozzle shape comes in two types: flat and wide nozzle tips. It is suitable for concentrated application using an ultrasonic spray nozzle and a pinpoint air transport fixture (custom order), as well as for transporting very small droplets (particles). These spray nozzles can be easily applied to applications where coating control and uniform film are required. The spray nozzle is lightweight and ideal for coating systems using robots. The main body of the spray nozzle is made of stainless steel. *Custom micro feed tubes are suitable for low flow application and are available in stainless steel or PTFE fluororesin. The spray nozzle can be equipped with a spray shaper for pinpoint spraying or a wider spray for better coating control. *Micro feed tubes are optional.

• nozzle
• Other machine elements
• Other physicochemical equipment

We will achieve a reduction in equipment investment and running costs.

The ultrasonic spray nozzle (atomizer) transmits vibrations from the piezoelectric ceramic, causing the liquid film to vibrate and forming fine particles for spraying. Liquid is supplied without pressure, allowing for the spraying of fine particles. It accommodates a wide range of liquid flow rates from a minimum of 10 milliliters per minute to a maximum of 100 milliliters per minute. Since no pressure is applied to the liquid, there is very little splatter or rebound, eliminating waste of the coating liquid and making large painting booths unnecessary.

• Ultrasonic Oscillator
• nozzle
• Other processing machines

Air transport fixture for spraying in a square or rectangular shape.

This is an air transport device designed to spray particles from an ultrasonic spray nozzle in a square or rectangular shape. Its main application is for coating purposes. By adding a small amount of gas or air, it applies to square, rectangular, or flat substrates. By adjusting the distance from the workpiece and the pressure of the transport gas or air, various sizes and shapes of spray patterns can be achieved with the ultrasonic spray nozzle manufactured by Sonia. *This product is a dedicated accessory for the ultrasonic spray nozzle made by Sonia.*

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

Designed for ultra-low flow rates of 1 ml/min or less.

The stainless steel micro feed tube made by Sonia is designed for extremely low flow rates of less than 1 ml/min. *Of course, it can also be used at flow rates above 1 ml/min. The liquid flows through without touching the tip, which forms a uniform particle size. *This product is an accessory specifically for Sonia's ultrasonic spray nozzle.

• nozzle
• spray
• others

Designed to use fast-reacting liquids and capable of stirring in a short time!

The Sonia dual micro feed tube is designed to use fast-reacting liquids and can be stirred in a short amount of time. The material is stainless steel. The dual micro feed tube has two liquid supply ports, one at the top and the other on the side. *This product is a dedicated accessory for Sonia ultrasonic spray nozzles.*

• nozzle
• others

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repair without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

Thank you very much for visiting our company website and catalog, and for your interest in our diesel engine generators. From customer surveys, we received the following feedback as the most common requests: - I want to see the actual generators that have been installed. - I want to see the operation under actual load. - I want to hear the opinions of companies that have installed the generators. - I want to see the operating generators before making a purchase. After all, it’s understandable to be concerned about purchasing a generator without seeing the actual unit first, right? As the saying goes, "Seeing is believing..." we will be holding this tour. It is located in that area of the Kanto region where the maximum temperature exceeds 40°C during the summer. We successfully operated it again this summer, so we are confident about handling the heat (sweat)... Furthermore, it has been confirmed that it is "fuel-efficient" due to the world-leading "Scania engine" installed. This will surely help reduce daily operating costs. Please note that while we will provide kind and courteous assistance, the meeting point and dispersal will be at the site (transportation costs and other expenses will be borne by the customer), so please understand this in advance. Contact: Kaneko

The non-contact beam touch sensor "HA-T401/HA-T520" has a compact detection range, making it an ideal automatic door sensor for installation on automatic doors facing narrow corridors or busy streets. Depending on the application and installation location, you can choose between "non-vision mounting type" and "non-vision built-in type." 【Features】 ● With the beam touch sensor, you can open and close the automatic door simply by bringing your hand close without touching it, ensuring hygiene. ● Depending on the installation environment, such as single sliding or bi-parting doors, the detection range can be set in four ways: left, center, right, with 4 spots and 12 spots settings. ● Two types of activation row settings are available to reduce unnecessary opening and closing of the automatic door due to cross traffic, contributing to energy-saving effects. ● The touch switch and infrared sensor are integrated, allowing for a switch between beam touch and infrared sensor modes with a single model. 【Recommended for such places!】 ☑ Entrances facing busy corridors ☑ Counters or signs near the door ☑ Buildings facing narrow corridors ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors ◎ For more details, please download the materials or contact us.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.