The metal tube case of φ19 can heat the passing gas to approximately 900°C.
The ABH series features a heating element that comes into direct contact with the heating gas. Despite its small outer diameter, it can heat the passing gas to approximately 900°C due to the adoption of a high-density heating element with a large surface area and good heat transfer efficiency. A heating element with a power range of 650w to 1600w has been integrated into a φ19 metal tube case. Please use it when a gas flow rate of 40 to 50 liters per minute is required. Accurate temperature control can be achieved using a thermocouple at the outlet. Since the temperature of the heating element can be monitored, safety measures against overheating can be implemented. The tip is threaded internally, allowing for the attachment of various fittings. There is also a ceramic paper protective tube for preventing near-miss accidents.
Inquire About This Product
basic information
A heating element of 650w to 1600w has been incorporated into the φ19 metal tube case. Please check the details on the website below: https://www.heat-tech.biz/products-nh/nh-ss/nph-gj-gz/839.html
Price range
Delivery Time
Applications/Examples of results
Cap seal Film shrink Re-dissolution of hot melt Torch for resin welding Heat sealing of paper packs Heat staking Heating and cutting of resin sheet materials Drying of coaters Drying of printed materials Drying of electric welding pipes Soldering of printed circuit boards Self-fusing of winding coils Deburring of resin molded products Heating of samples for electron microscopy Ignition source for burners Processing of grilled tofu End processing of fibers Production of heated nitrogen gas Preheating of resin sheets Preheating of printed circuit boards Material surface analysis Operational testing of thermoswitches Partial heating of culture media Production of heated sterilizing air Thermal distortion testing of liquid crystals Heating of ammonia gas Seal peeling Heat shrink of lithium batteries Dehumidifying drying of resin pellets Drying of silicon wafers Heating and disinfecting of liquids Uniform heating of culture media Water removal and drying of metal films Water removal of glass bottles Replacement of gas in all-electric laboratories Drying of printed wire marks Aging of electronic components Adhesion of film and paper Drying of processing holes Internal drying of pipe products Prevention of double feeding and preheating of blank materials Water removal and drying of surface-treated steel plates Water removal and drying of engine blocks Rapid heating within processing chambers
Detailed information
-
Self-fusing of winding coils Issues There were problems with residual winding twists in fine wires. ⇒ Improvement Points The winding wire was heated with a hot air heater to restore the twist and smooth it out. After coiling, the entire assembly was heated to induce self-fusion. Precise temperature control was achieved, resulting in improved processing accuracy.
-
Production of Heated Nitrogen Gas Issues It was not possible to produce high-temperature nitrogen gas while maintaining purity. ⇒ Improvement Points By heating with a hot air heater, it became possible to produce high-temperature gas while maintaining high purity without air contamination.
-
Heat shrink for lithium batteries Issues We were struggling with precise temperature control because we were using an industrial dryer. ⇒ Improvement points We heated the surface with a hot air heater using a small amount of heat to achieve shrinkage. Since the battery itself was not heated, reliability was improved.
catalog（1）
Download All Catalogs
Company information
5 reasons that HEATTECH is selected 1. The rich selection of 5 principles and 71 types. Air Blow heater , Near-infrared, Middle-infrared, Far-infrared, and UV heater From the 71 types of products based on the 5 principles of heating system, we will propose the best heater. 2. 9 series 88 types of heater controllers． Manual, Automatic, Speed proportional, Remote control, IOT compliant, Noncontact heating control, One-shot heating, Multistage heating, etc. We propose the optimal heater controller from the multifunctional products. 3. Construction method study materials We have published a number of technical documentation online seminars. 4. Sense of security of verification before introduction. Test piece, test laboratory, in user can verify before introduction. 5. Low-budget one-stop introduction To introduce in testing way, the laboratory kit which gathered something necessary was prepared. : Member of the Kobe Chamber of Commerce and Industry : Member of the Society of Material Science Japan : Member of the Society of Thermophysical Properties Japan : Member of the Japan External Trade Organization Trade Tie-up Promotion Program
