ペルノックス Product Lineup

For the conductive connections around sensors of artificial satellites, superconducting devices such as MRI, and ultra-low temperature experimental equipment. In tests where the sample is immersed in liquid nitrogen for 30 seconds and then left at room temperature for 30 minutes, repeated 10 times, the adhesive strength is maintained at approximately 70% or more. This is proposed as a bonding method for electronic components used in ultra-low temperature environments. ONE-HAND MIXING is a product that can automatically mix and dispense a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, which suppresses variations in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive adhesion is possible for materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel, without using a soldering iron. - It retains flexibility after curing and can be used for repairs and connections in areas subject to bending and vibration. * For detailed data, please check the TDS and the special website.

For repairing poor conductivity or disconnections in equipment and facilities used in cold environments. It has been confirmed that the adhesive layer functions stably even in environments where rapid temperature changes occur, avoiding solder heat with room temperature curing. This expands options for maintenance and on-site repairs. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive bonding is possible without using a soldering iron, even with materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subjected to bending and vibration. *For detailed data, please check the TDS and special website.

For sites and educational purposes that want to avoid the risks of burns and component charring from high-temperature soldering iron work. ONE-HAND MIXING is a room-temperature curing type that does not require a heat source, allowing for application with a single-handed push, enabling safe electrical connections of wires and components. ONE-HAND MIXING is a product that automatically mixes and dispenses a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for electrical connections around heat-sensitive resin components, FPCs, LEDs, and sensors. - Conductive bonding is possible without using a soldering iron, even on materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and special website.

For wiring and connections in environments where it is difficult to manage safety during high-temperature operations or where heat sources are not desired. It cures at room temperature, is not classified as a pharmaceutical hazardous substance, and complies with RoHS/REACH, reducing the burden of handling, transportation, and storage. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, minimizing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPC, LEDs, and sensors. - Conductive bonding is possible without using a soldering iron, even with materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and the special website.

For repairing the broken lines of the rear window defogger (heating wire) in vehicles. It has low viscosity, making it easy to draw lines, and can repair heating wires on glass that are difficult to solder, curing at room temperature. Its use is expanding in repair sites, including import car dealerships. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive containing silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - It enables conductive bonding to materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel, without using a soldering iron. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and special website.

For repairs around terminals that cannot withstand heat or mechanical stress, such as the defroster tab of the rear window, we support urgent repairs and short delivery times with high adhesive strength and conductivity, made in Japan and available for immediate delivery. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive bonding is possible without using a soldering iron, even with materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subjected to bending and vibration. *For detailed data, please check the TDS and the special website.

This product is intended for applications where you want to form conductive pathways on surfaces or flexible substrates, similar to drawing lines. It allows for the formation of conductivity at room temperature, even on substrates that are difficult to solder, thereby expanding the design freedom for circuit design in prototypes, demonstration units, and wearable considerations. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive containing silver fillers using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive adhesion is possible on materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel, without using a soldering iron. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and the special website.

For the conduction fixation of movable parts and bending sections. ONE-HAND MIXING is a flexible cured material that can conduct electricity even when bent. It is suitable for examining connections in areas where stress is applied, such as around FPCs and cables. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, which suppresses variations in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive adhesion is possible without using a soldering iron, even for materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing and can be used for repairs and connections in areas that experience bending and vibration. *For detailed data, please check the TDS and the special website.

As a conductive adhesive that allows for simultaneous bonding and electrical conduction without using a soldering iron, it is suitable for electronics projects and circuit board repairs. Since there is no heating process, it reduces the risk of burns, enabling even those who are not skilled at soldering to make electrical connections. ONE-HAND MIXING is a product that automatically mixes and dispenses a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing is required, which helps to suppress variations in the mixing ratio by the operator. - It cures at room temperature, making it suitable for electrical connections in heat-sensitive resin parts, FPCs, LEDs, and sensor areas. - Conductive bonding is possible without using a soldering iron, even with materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, allowing it to be used for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and the special website.

For experiments, practical training, and STEAM education at universities, technical colleges, and schools. It allows for the experience of conductive connections and circuit formation through an approach different from soldering, and can be utilized as a learning material for conductive materials. We are also advancing verification of educational applications with universities. ONE-HAND MIXING is a product that can automatically mix and dispense a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive adhesion is possible without using a soldering iron, even on materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and special website.

For those considering conductive adhesive for substrates that undergo reflow heating in post-processing. ONE-HAND MIXING provides evaluation data on reflow resistance in technical documentation, allowing you to confirm changes in conductivity and adhesion during heating behavior and environmental testing. ONE-HAND MIXING is a product that automatically mixes and dispenses a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections in heat-sensitive resin parts, FPCs, LEDs, and sensor areas. - Conductive adhesion is possible without using a soldering iron, even on materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *Please check the TDS and special website for detailed data.

For grounding connections and continuity repairs of equipment and facilities used outdoors. We publish data on weather resistance test results and changes in conductivity and adhesion during environmental testing as technical documentation to support considerations for outdoor applications. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No measuring or mixing work is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive bonding is possible with materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel, without using a soldering iron. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please refer to the TDS and special website.

For applications where you want to minimize connection resistance even with conductive adhesives. ONE-HAND MIXING achieves a volume resistivity of 2×10⁻⁴Ω·cm at room temperature curing stability, approaching the conductivity of solder. It is suitable for conductive connections and repairs where low resistance is required. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing work is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive bonding is possible without using a soldering iron, even on materials that are difficult to solder, such as glass, resin, aluminum, and SUS. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and special website.

This is a conductive adhesive that does not fall under the category of pharmaceutical-grade hazardous substances and complies with RoHS and REACH regulations. It can be stored at room temperature, eliminating the need for refrigeration or freezing, which reduces the burden of storage, transportation, and management in universities, research institutions, and corporate environments. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive containing silver fillers using a dedicated cartridge and mixer nozzle. - No weighing or mixing is required, which minimizes variations in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections in heat-sensitive resin parts, FPCs, LEDs, and sensor areas. - It enables conductive bonding to materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel, without the use of a soldering iron. - It retains flexibility after curing, allowing for repairs and connections in areas subject to bending and vibration. *For detailed data, please refer to the TDS and the special website.

We address issues such as unstable delivery times for overseas conductive adhesives, the need for refrigerated storage, and classification as hazardous materials. With domestic manufacturing and an immediate delivery system, we support urgent repairs and quick evaluations. We also offer bulk purchase discounts for corporations. *Consultation required. ONE-HAND MIXING is a product that allows for the automatic mixing and dispensing of a two-component conductive epoxy adhesive containing silver filler using a dedicated cartridge and mixer nozzle. - No weighing or mixing is required, reducing variability in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections in heat-sensitive resin parts, FPCs, LEDs, and sensor areas. - Conductive bonding is possible with materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel, without using a soldering iron. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and special website.

The mixer-integrated cartridge allows for automatic mixing and dispensing of two liquids in the appropriate ratio with a one-handed push. It prevents variations and failures caused by weighing and manual mixing, enabling anyone to perform stable conductive bonding and repair work. ONE-HAND MIXING is a product that can automatically mix and dispense a two-component conductive epoxy adhesive with silver filler using a dedicated cartridge and mixing nozzle. - No weighing or mixing work is required, reducing variations in the mixing ratio by the operator. - It cures at room temperature, making it suitable for conductive connections around heat-sensitive resin parts, FPCs, LEDs, and sensors. - Conductive bonding is possible without using a soldering iron, even on materials that are difficult to solder, such as glass, resin, aluminum, and stainless steel. - It retains flexibility after curing, making it usable for repairs and connections in areas subject to bending and vibration. *For detailed data, please check the TDS and special website.