アイ・ティー・エス・ジャパン List of Products and Services

The "GI-M023" is an electric pencil hardness tester that measures the hardness of paint coatings in accordance with Wolff Wilborn standards. It is commonly used in experimental analysis and quality control, and is applicable for paint treatments, furniture, vehicles, mobile phones, computers, translation devices, digital cameras, and more. It can measure both single-layer and multi-layer coatings, allowing for fast and convenient operation. 【Applicable Test Standards (partial)】 ■ASTM D3363 ■ECCA T4 ■MIL C27 227 ■NEW 5350 ■SIS 184187 *For more details, please refer to the related link page or feel free to contact us.

The "GI-M043" is a device developed for wear testing of solar panel surfaces. The wear test is conducted using wool. The wool rotates while moving in a circular motion, rubbing against the test specimen. The friction characteristics of the solar panel surface are evaluated under specified load and number of cycles according to the testing conditions. The corresponding testing standard is BS EN 1096-2. 【Specifications (partial)】 ■ Measurement stroke: 10-150mm (adjustable, typically 145mm used) ■ Measurement speed: 10-120cpm (digital, adjustable) ■ Measurement count: 1-999,999 times *For more details, please refer to the related link page or feel free to contact us.

This is a melt indexer that measures MFR (Melt Mass Flow Rate) and MVR (Melt Volume Flow Rate), which serve as guidelines for the melt flowability of resins. The touch panel has pre-programmed ISO/ASTM tests, allowing for easy operation and testing through the panel. Analysis of test data and data output to USB can also be performed via the panel. We also offer optional blocks for materials with high flowability and fixtures for MVR measurement. The testing machine is compactly designed, and temperature is detected above the diamond die, ensuring high accuracy. Calibration of the weights placed on the piston and calibration at different temperature levels are also conducted to enhance the reliability of the measurement data. You can also try a demo measurement before purchase. Additionally, we accept commissioned testing. Please feel free to consult with us. *For more details, please refer to the PDF document or feel free to contact us.*

The "QC-657B" is a load deflection temperature (HDT) testing machine. It applies a constant stress in accordance with the testing method to the center of a sample supported at both ends. The sample is heated at a constant rate of 2°C per minute in a liquid heating bath, and the heat distortion temperature (HDT) is recorded when the deflection at the center reaches the specified value. With the optional cooling function, the testing cycle time can be significantly reduced. It can test up to three samples simultaneously and can accommodate both load deflection temperature tests and Vicat softening temperature tests by changing the testing fixtures. 【Features】 ■ 7-inch touch screen, displays measurement data for up to 3 samples ■ Data output in Excel format ■ User-friendly interface with easy operation in step format ■ Load deflection temperature measurement through fixture exchange *For more details, please refer to the related link page or feel free to contact us.

The "QC-801" is a room temperature tape adhesion strength testing machine that automatically measures time and records the time of tape detachment. When adhering, a 2kg weight is used to press the test piece, and a weight is placed underneath the test piece. The counter automatically stops when the test piece falls from the stainless steel plate. If the tape does not fall within the specified time, the displacement distance is measured and evaluated. 【Features】 ■ Provides multiple measurement jigs, allowing for simultaneous long-duration measurements ■ Automatic time measurement, recording the time of tape detachment ■ Steel plates and weights are manufactured according to standards to ensure data accuracy ■ A urethane cushion is provided at the drop point to absorb the impact on the testing machine and the weight when it falls ■ The main body can be designed to be stackable, reducing time when conducting large-scale measurements *For more details, please refer to the related links or feel free to contact us.

We would like to introduce our constant temperature tape adhesion testing machine, the 'QC-802A'. In a high-temperature environment, a 1-inch wide bar tape is applied to a stainless steel plate, and a standard roller weighing 4.5LB is used back and forth at a speed of 300mm per minute. By placing the steel plate on the tester and adding the specified counterweight, the required temperature can be set. When the tape peels off from the steel plate, the timer automatically stops counting and records the adhesive holding time of the tape. 【Features】 ■ Multiple sets of measurement jigs are available, allowing for simultaneous long-duration measurements. ■ Automatic counting, keeping track of tape drop-off time. ■ Ensures data accuracy with steel plates and weights compliant with standards. *For more details, please refer to the related links or feel free to contact us.

A testing machine that measures the force required to peel off tape, known as peel force (adhesive force). Easy operation with a 5-inch touch panel. Crimping speed of 50 to 1200 mm/min. Up to 99 cycles can be programmed.

We would like to introduce our ball tack tester for 1-point/4-point use, the 'QC-805/805A'. "Initial adhesive strength" refers to the ability to adhere to a substrate with light force in a short time. This product sets the inclination angle at 30 degrees, with a 100mm length of the ball's runway, allowing a steel ball to roll and stop at the measurement section of 100mm. The strength of the tack is represented by the size of the steel ball indicated by its number. 【Applicable Test Standards】 ■ JIS Z0237 ■ GB/T 4852 *For more details, please refer to the related links or feel free to contact us.

We would like to introduce our PSTC-style rolling ball tack tester, the 'QC-805P'. Before testing, clean the surface of the runway and the steel ball with a solvent, and apply a tape measuring 1 inch in width and 15 inches in length to the front of the runway. Use a clean, dry clip to place the steel ball on the release bar and release the ball. Measure by allowing the ball to roll directly until it stops on the sample, and after five tests, calculate the average value and measure the distance. 【Applicable Test Standards】 ■PSTC 6 ■ASTM 3121 *For more details, please refer to the related links or feel free to contact us.

At Comtech, we manufacture a variety of types of physical property testing machines in-house. Since we handle both design and manufacturing ourselves, we can accommodate custom orders as well. Additionally, we have a robust support system in place, allowing for quick repairs and maintenance within our company. ■ Product Lineup ◎ Universal Material Testing Machines / Related Products ◎ Impact Testing Machines ◎ PC Hydraulic Material Testing Machines ◎ Wear Testing Machines ◎ Opening Torque Testing Machines ◎ Melt Indexers ◎ Heating Deformation and Vicat Softening Testing Machines ◎ Thermal Press Molding Machines ◎ Fatigue Testing Machines ◎ Spinning Testing Machines ◎ Packaging Material Testing Machines ◎ Tape and Adhesive Testing Machines ◎ Environmental Testing Machines ◎ Specimen Testing Machines ◎ Hardness Testers ◎ Other Testing Machines Please feel free to contact us for more details.

This document provides information on how to choose a universal testing machine from Comtec, a comprehensive manufacturer of physical property measurement testing machines. For "load," you can choose from five types such as "500N" or "2kN to 5kN." Additionally, there are models available with height variations to suit the application of the tests. Please feel free to download and take a look. 【Contents (partial)】 ■ Load ■ Testing (jigs) ■ Software ■ Options *For more details, please refer to the PDF document or feel free to contact us.

The QC-662B is a Vicat softening temperature testing machine that supports simultaneous measurement of up to 3 samples and displays the deflection and temperature of each sample during measurement. A probe with a tip area of 1 mm² is placed at the center of the sample under a constant load of 10N (or 50N), and the sample is heated at a constant rate of 50°C per hour in a liquid heating bath. The Vicat softening temperature (VST) is recorded when the probe has sunk 1 mm. Operation is performed via a touch panel, and the standardized operating procedures allow for easy measurement initiation through step-by-step operations. 【Features】 ■ 7-inch touch screen: Displays measurement data for up to 3 samples ■ Data output in Excel format ■ User-friendly interface: Easy operation through step-by-step format ■ Measurement of load deflection temperature by exchanging fixtures *For more details, please refer to the related links or feel free to contact us.

The "QC-104H" is a bending fatigue testing machine used to evaluate the bending resistance and flexural strength of materials such as paper, resin films, aluminum foil, copper foil, and flexible printed circuit boards. Samples are typically bent repeatedly between +135° and -135°, and the bending resistance is assessed based on the number of cycles until breakage occurs. Test conditions such as the number of bends and speed are input via the 5-inch touchscreen of the device. Additionally, the testing machine automatically stops when breakage of the sample is detected or when the set number of test cycles is completed. 【Specifications (partial)】 ■ Load capacity: up to 50kg (varies with test stroke) ■ Stroke: up to 160mm ■ Sample length: up to 180mm ■ Number of test samples: up to 5 ■ Test speed: 20–500 r.p.m. *For more details, please refer to the related links or feel free to contact us.

The "QC-659H" is a bending test machine for cables used in electrical products. It evaluates the bending performance of the cable based on the number of bends until the copper wire inside the cable becomes an open circuit due to excessive bending. In addition to a monitor (touch panel color), this machine is equipped with features such as over-count stop, break stop, temporary stop function, and emergency stop function. 【Features】 ■ Operated via a touch panel, enhancing usability ■ Switchable between English and Chinese ■ Immediate display of the machine's operating status, including during measurement, stop, and measurement results ■ Equipped with a timer that can automatically calculate measurement time ■ Over-count stop function can be set, up to a maximum of 99,999,999 counts ■ Test speed can be set digitally, with a speed range of 10 to 100 CPM *For more details, please refer to the related links or feel free to contact us.

The QC-116 is an electronic Mullen burst testing machine that measures the burst strength of materials such as paper, cardboard, leather, textiles, and synthetic leather. Equipped with a monitor (touch panel), it allows for the calculation of error compensation values. It can adjust the calibration parameters of the sensing components, improving measurement accuracy. Additionally, it features a load graph function that enables immediate reading of test conditions, and it allows for unit switching, making it easier to interpret test results. 【Features】 ■ Equipped with a monitor (touch panel) ■ Adjustable calibration parameters for sensing components ■ Load graph function included ■ Unit switching available (metric or imperial units) ■ Measures burst strength of materials such as paper, cardboard, leather, textiles, and synthetic leather *For more details, please refer to the related links or feel free to contact us.

The QC-301 is a manual measuring device that measures the tensile strength of reels and weighs the weight with a scale to measure the yarn count or tex. It operates at a speed of 30 to 300 RPM, either manually or electrically. It rotates the winding frame to take a constant number of rotations and a specified length of thread. It complies with testing standards such as ASTM D1059, ASTM D2260, ISO 7211, ISO 2060, and BS 2010. 【Specifications (partial)】 ■ Number of winding threads: 4 ■ Rotation speed: Manual control ■ Winding frame circumference: 1m/revolution or 1.5 yd/revolution ■ Counter: Capable of reading 0 to 9,999 revolutions ■ Main body dimensions: 80 × 43 × 65 cm *For more details, please refer to the related links or feel free to contact us.

The "QC-302A" is an electric measuring device that rotates the winding frame to take a constant number of rotations and a specified length of thread. It measures the reel's tensile strength and weighs it on a scale to determine the yarn count or tex. It has a winding thread count of 6, with a rotation speed of 30 to 300 r/min. This product complies with the testing standards ASTM D1059/D1907/D2260, ISO 7211/2060, and BS 2010. 【Specifications (partial)】 ■ Winding thread count: 6 ■ Rotation speed: 30–300 r/min ■ Winding frame circumference: 1 meter/revolution (optional specification of 1.5 yards/revolution available) ■ Counter: 5–9,999 revolutions ■ Main body dimensions: 75 × 68 × 50 cm ■ Weight: 55 kg *For more details, please refer to the related links or feel free to contact us.

The "QC-309D" is an electric twisting machine that automatically detects the length of the test specimen and the twist level of the spun yarn, displaying the information on the screen. After twisting the spun yarn, it measures the twist level based on the length condition, indicating differences in characteristics and measuring changes in twisting with sensors. Additionally, when testing high twist level specimens, the measurement speed decreases before the end of the test, allowing for more accurate detection. 【Features】 ■ Measures twist level based on changes in spinning ■ Built-in reference table for tensile force data and test loads for various wires ■ Automatically detects the length of the test specimen and the twist level of the spun yarn, displaying it on the screen ■ Allows users to better understand the progress of the test ■ Capable of analyzing test data and providing test results *For more details, please refer to the related links or feel free to contact us.

The QC-317A is a pressure-type waterproof testing machine that allows for the setting of clamping pressure. It applies pressure to waterproof textile products at a constant rate, and the pressure at which water emerges from three points on the back of the test specimen is the waterproof rating. The testing methods are divided into three types: water pressure method, constant water pressure method, and leakage method. Please feel free to contact us if you need assistance. 【Testing Methods (Partial)】 ■ Water Pressure Method - Raise the water level at a speed of 1 cm/sec. - Record the water level height until water emerges from three points on the back of the test specimen. ■ Constant Water Pressure Method - Raise the water level to a constant level and leave it. - Record the time until water emerges from three points on the back of the test specimen. *For more details, please refer to the related links or feel free to contact us.

The "QC-309E" is a manual twisting machine that automatically detects the length of the test specimen and the twist level of the spun yarn, displaying this information on the screen. After twisting the spun yarn, it measures the twist level based on the length condition, indicating differences in characteristics and measuring the twist level through changes in spinning using sensors. Additionally, when conducting tests on high twist level specimens, the measurement speed decreases before the test is completed, allowing for more accurate detection. 【Features】 ■ Measures twist level based on changes in spinning ■ Built-in reference table for tensile force data and test loads for various wires ■ Automatically detects the length of the test specimen and the twist level of the spun yarn, displaying it on the screen ■ Allows users to better understand the progress of the test ■ Capable of analyzing test data and providing test results *For more details, please refer to the related links or feel free to contact us.

The "QC-317F" is an electronic waterproof testing machine that can perform measurements in both dynamic and static forms. The maximum measurement pressure can be adjusted within the range of 4.5 kgf/cm² and 0.05 to 4.5 kgf/cm²/min, satisfying various testing standards. Additionally, it is equipped with a 7-inch monitor (touch panel), high-precision pressure sensors, and a pressure controller system. Measurements are stable and highly accurate, with the measurement process displayed in real-time on a pressure-time graph, allowing for the verification of pressurization speed and immediate pressure status. 【Features】 ■ Satisfies various testing standards ■ Real-time water temperature display and pressure graph display ■ Multiple measurement methods, with the possibility to set three-stage conditions ■ Expanded measurement space capable of measuring fabric for a single garment ■ Safety stop device that automatically reduces pressure when the test specimen bursts *For more details, please refer to the related links or feel free to contact us.

The "QC-317M/N" is a manual waterproof testing machine that does not require a power supply for testing. By continuously pressing and releasing the air inflating ball, pressure is applied to the pressurization seat and maintained at a rate of 1 kg/cm²/min. When water seeps out from three points on the back of the test specimen, the pressurization is stopped, and the reading on the pressure gauge is recorded. We observe whether water seeps out after applying a constant water pressure for a certain period. 【Specifications (partial)】 ■ Test specimen dimensions: 12×12 cm ■ Pressurization surface diameter: 9.4 cm ■ Test specimen clamping: manual grip ■ Body dimensions: 35×20×32 cm (W×D×H) ■ Weight: 5.9 kg *For more details, please refer to the related links or feel free to contact us.

The QC-643B is a rigidity testing machine designed to measure and evaluate materials such as hard, thin, and small sheets (e.g., brush bristles, flexible plates, etc.). It measures the load through the reaction force of bent materials, and this product allows for the test specimen length to be set at distances of 1, 5, 10, 15, 20, 25, and 50 mm, with tests conducted at angle conditions of 1-90°. Different distances and angles can be selected based on the test specimen to determine the maximum load after bending. 【Specifications (partial)】 ■ Test capacity: Maximum 500g ■ Measurement angle: Adjustable from 1-90° ■ Measurement lengths: 1, 5, 10, 15, 20, 25, 50 mm ■ Speed rate: 5° to 100° / sec ±5% (adjustable) ■ Accessories: Software cable *For more details, please refer to the related links or feel free to contact us.

The "QC-GSA" is a constant pressure loading platform that provides precise loads for accurate and reproducible hardness measurements. It reads the maximum value indicated immediately after the sample makes contact with the pressing surface of the durometer, and that value represents the "hardness." The average value from five locations is used as the hardness value, and the thickness of the test piece and measurement positions comply with the standards of each durometer. 【Specifications (partial)】 ■ Load range: 1kg, 5kg (1kg + 4kg) ■ Measurement schedule: 170mm ■ Main body dimensions: 18×20×42cm ■ Weight: 18kg ■ Mounting tooth tip type: M6x5mm (or specified) ■ Test table diameter: Φ770mm *For more details, please refer to the related links or feel free to contact us.

We would like to introduce the C-type durometer 'GS-701N', which is suitable for soft materials and is handheld. By applying a specified load to the flat surface of the sample, the value displayed on the dial is read as the material hardness. Since samples with different hardness have varying area and thickness conditions, it is necessary to measure the average value from 5 to 10 readings as the material hardness. 【Specifications】 ■ TYPE: C-type ■ Applicable materials: Foam (PU) ■ Accuracy: ±1 degree ■ Indenter shape: Φ5.08mm semicircular ■ Measurement range (specimen): 10mm or more ■ Constant pressure load base weight: 1kg *For more details, please refer to the related links or feel free to contact us.

We handle the Comtech D-type durometer 'GS-702N'. By applying a specified load to a standard material plane and reading the values on the display, we evaluate the material hardness. It is suitable for testing soft materials such as non-metals. Since the required area and thickness of the test specimen vary depending on the hardness of the material, it is necessary to conduct approximately 5-10 measurements to obtain accurate material hardness. 【Specifications】 ■TYPE: D-type ■Applicable materials: Plastic (hard) A value > 90 or higher ■Accuracy: ±1 degree ■Indentation shape: Needle tip R0.1mm 30° conical shape ■Measurement range (test specimen): 6mm or more ■Constant pressure load platform weight: 5kg *For more details, please refer to the related links or feel free to contact us.

The QC-337 is a Elmendorf-type tear strength testing machine that measures the strength at the beginning of tearing for materials such as paper, textiles, and PVC. After fixing the test specimen, a knife is used to make a cut in the specimen, and the specimen is torn using the energy from the swinging pendulum. The tear strength is calculated from the change in the position of the indicated pointer. The tear strength is displayed on the scale. 【Specifications】 ■ Test specimen dimensions: 63.5 × 100 mm ■ Capacity: 20–3200g / 0–6400g (switchable), with weights included ■ Main unit dimensions: 47 × 25 × 38 cm ■ Weight: 25kg *For more details, please refer to the related links or feel free to contact us.

The "QC-701A" is a color matching cabinet manufactured by Comtech. Color judgment varies under different lighting environments, and this product provides commonly used lighting conditions such as D65 standard daylight, UV fluorescent reaction light, and A sunset light. Additionally, it has a device that records the usage time of each light source, allowing for monitoring of the lamp's lifespan. 【Features】 ■ Simulates various lighting conditions ■ Provides an objective standard environment for conducting sample color comparisons ■ Allows for monitoring of lamp lifespan ■ The cabinet is painted gray ■ Comes with a spacing light cover, ensuring uniform light source without concentrated light spots *For more details, please refer to the related links or feel free to contact us.

The "Disper Tester 3000 Plus" is a fully automatic filler dispersion testing machine for rubber. The autofocus feature automatically adjusts the focus for sample imaging. Since the adjustment of the shooting location is done internally within the device, there is no need to move the sample position. A dedicated auto sampler is available for purchase separately, capable of holding 50 samples. 【Specifications (excerpt)】 ■ Magnification: 100x ■ Aperture: 12mm x 3.5mm ■ Particle size: 1μm to 250μm ■ Light source: LED light ■ Interface: USB 3.0 *For more details, please refer to the related links or feel free to contact us.

The "DM 3000" is a density testing machine equipped with a semi-automated test sequence and an automatic calibration system. This compact device is designed for rapid and accurate density and specific gravity measurements, capable of performing up to four measurements per minute under software control. It uses the buoyancy weighing method to compare the weight of samples in air and submerged in water. Measurements can also be taken for densities lower than 0.50 to 10.00 g/cm³ by using optional anti-float brackets or needle holders. 【Specifications (excerpt)】 ■ Measurement data: Density, specific gravity, volume change ■ Measurement range: 0.0 to 420 g (0.0 to 160 g) ■ Sample weight: 1.000 to 50.000 g ■ Reproducibility: ±0.020% or less ■ Power specifications ・Single-phase: 100V - 260V, rated: 2A 50/60Hz *For more details, please refer to the related links or feel free to contact us.

The "HT 3000" is a device that accurately measures hardness, which is one of the important physical properties of rubber products and components. It features a new design with a digital display that is easy for anyone to read. With automation through the "automatic sample loader" and various options such as a "positioning device," it caters to a wide range of customer needs. Additionally, we offer the modular "HT3000 Modular," so please feel free to contact us when needed. 【Product Range】 ■HT 3000-A: Digital handheld Shore A durometer ■HT 3000-D: Digital handheld Shore D durometer ■HT 3000-S: Low-pressure holding base with calibration weights for durometers ■HT 3000-SA: Automatic hardness testing holding base *For more details, please refer to the related links or feel free to contact us.

The "HT3000CH" is a hardness testing machine that measures the change in rubber hardness under extreme conditions ranging from -40°C (with an option for -70°C) to 180°C. It is equipped with an auto sampler, allowing for rapid and efficient automatic measurements. Additionally, a humidity control system can be added as an option. All test sequences are conducted according to the software-guided sequence. 【Features】 ■ Equipped with an auto sampler ■ Capable of both fully automatic and manual measurements - Can set up to 25 samples on a rotating tray - Measurement process precisely controlled by a control program ■ All data during measurement is automatically saved to a database *For more details, please refer to the related links or feel free to contact us.

The "FT3000" is a linear drive-type durability and fatigue testing machine that has the capability to measure both "fatigue due to stretching" and "cracking due to bending." It is designed for continuous research and development as well as quality control, allowing for the simultaneous measurement of 16 samples under a precisely controlled temperature environment. Frequency, grip distance, and dynamic stroke can be freely set. 【Features】 ■ Achieves stretching fatigue and bending fatigue (De-Mattia) testing with a single machine ■ Can accommodate a total of 16 samples on a stainless steel grip, allowing for simultaneous measurement ■ Measurement in a highly accurate temperature environment ■ Uses a digital control panel ■ Adjustable cycle settings *For more details, please refer to the related links or feel free to contact us.

The "RB3000" is a pendulum-type automatic elasticity tester that measures the rebound elasticity of rubber and elastomer materials. It measures the rebound elasticity from the "return energy" and "impact energy" generated between the "hammer fin," "sample," and "RB3000." The test samples that can be measured are rubber or elastomer materials, in the form of button-type or small pieces, with a hardness range of 30 to 85 (shore A [IRHD N]). 【Features】 ■ A rebound tester that accurately measures the rebound force of rubber compounds ■ Easy operation with a 7-inch multi-touch screen ■ The pendulum has a hammer fin with a diameter of 15mm ■ Measures rebound elasticity from return energy and impact energy ■ Test samples that can be measured: rubber or elastomer materials *For more details, please refer to the related links or feel free to contact us.

The "ABR 3000" is a device that allows for easy and accurate execution of wear tests without errors, using the Montec rotary drum wear testing machine. The test sample is fixed in a quick-clamp sample holder and is pressed against a sheet of abrasive wrapped around the rotating drum at a specified distance and load, with the option to rotate. The friction loss coefficient is calculated by comparing the weight of the test sample before and after the test. 【Specifications (excerpt)】 ■ Abrasive cloth size: 472.5mm (+2) × 400mm ■ Film tape size: 50mm × 0.2mm ■ Wear distance: 40m (20m) ■ Abrasive cloth grit: 60 mesh ■ Maximum grip length: 16mm *For more details, please refer to the related links or feel free to contact us.

The "CC 3000" was developed to evaluate the service performance of industrial rubber products, such as solid tires for industrial use and conveyor belts that transport sharp objects like rocks, gravel, glass, and metal. In addition to being "fast" and having "low running costs," it is equipped with a reliable high-level standard in inspections that predict actual product performance. A circular sample placed on a rotating axis is subjected to impacts controlled precisely in terms of frequency and cutting time using a sharp tungsten carbide knife for measurement. 【Features】 ■ Fast ■ Low running costs ■ Reliable in inspections that predict actual product performance ■ Measurement through impacts controlled precisely in terms of frequency and cutting time ■ Once the pre-set measurement time is completed, a cylinder automatically lifts the knife's auxiliary arm *For more details, please refer to the related links or feel free to contact us.

White light is divided by wavelength. It can be reflected in a unique measurement scale at the "vertical focus." ◎ Distortion and curvature are also measured ◎ Wide area processed at high speed ◎ No refocusing required ◎ Clear images ◎ No sample pretreatment needed ◎ Can measure any color ▶ Non-contact measurement ▶ Maximum vertical resolution = 1nm ▶ Maximum surface angle = 87° ▶ No data stitching

The Tribometer from Nanovia is a powerful and highly adaptable all-in-one friction and wear testing machine equipped with the widest range of test modules and environmental modules available on the market. Due to its simple design, the Nanovia Tribometer allows for quick exchanges to meet any research needs, requirements, and standards. Advanced pneumatic technology enables stable application of normal forces at speeds ranging from 0.001 to 15,000 rpm (over 10 m/s), allowing for high-precision evaluation of wear, scratches, friction, lubrication, and mechanical properties, with instant measurements taken by built-in sensors. Additionally, we offer a variety of "environmental test modules" designed for harsh load conditions. With a rich selection of attachment modules, we can customize and propose various types of tests.