シロ産業 List of Products and Services

● Waterproof design for the front panel ● Data hold function ● Peak value display function ● Maximum and minimum value display function

It measures the irradiance (W/m²), defined as the ratio of the radiation flux (W) incident on a surface to the unit area (m²), in the UVA / UVB / UVC spectral range. With the adoption of a new photodiode, it is insensitive to ? and infrared light. The outdoor installation type is the MC8P-PHOT3S series. ■mV signal output In the spectral regions of VIS-NIR, UVA, UVB, and UVC, it measures light and radiation amounts as illuminance (lux) or irradiance (W/m²). Additionally, it is capable of measuring the number of photons per unit time and unit area in the photosynthetically active radiation (PAR) wavelength range of 400–700 nm. The WPLP series does not require an external power supply.

WPLP-RAD-01 measures the radiant intensity (W/m²), defined as the ratio of the radiant flux (W) incident on a surface to the unit area (m²), in the VIS-NIR spectral range (400–1050 nm). These features are applicable to instruments suitable for measurements in the visible and near-infrared regions. The calibration of the probe uses the 577/579 nm line of a Xe-Hg (xenon-mercury) lamp through a spectral interference filter. The outdoor installation type is the MC8P-PHOT3S series.

The 【WPLP-PAR-01】 measures the number of light quanta incident on a surface per second in the spectral range of 400 to 700 nm, and the ratio to the unit area (m²). This quantity is defined as PAR, or Photosynthetically Active Radiation. The calibration of the probe is performed using a halogen lamp, with specific spectra being referenced against known spectral radiation. The spectral response of the probe is slightly affected by temperature. Thanks to the special structure of the diffuser and probe, it also responds to changes in the angle of incidence on the diffuser, which is corrected for the cosine law. The outdoor installation type is the MC8P-PHOT3S series.

The spectral response curve of the light measurement probe approximates the human eye's response curve known as the standard photopic curve V(λ). The difference between the "WPLP-PHOT-01" in spectral response and the standard photopic curve V(λ) is calculated as the error f'1. Calibration of the probe is performed by comparing it with a photometer that has been calibrated by a primary metrology standard institution. The calibration procedure complies with CIE Document No. 69 (1987) "Method of Characterizing Illuminance Meters and Luminance Meters." Measurements are conducted by illuminating the probe with standard light A. The outdoor installation type is the MC8P-PHOT3S series.

Handheld color luminance meter. It is a device that measures the luminance of LCDs (liquid crystal displays), PDPs (plasma display panels), LEDs, CRTs (cathode ray tube displays), and more. Additionally, it can measure the chromaticity and color temperature of various light sources and lighting fixtures.

This is a resin molded product evaluation measurement device that enables numerical management of weld lines, flow marks, whitening scratches, gloss scratches, and other surface defects. It can also evaluate scratches on products with leather textures or matte finishes.

This is a handheld densitometer (reflectance density meter) ideal for managing gloss and reflectance density of electronic devices, metals, building materials, precision instruments, and more. It can also be used to manage the reflectance density (OD) and reflectance of printed materials and paper.

● It can be operated with one hand, so it is highly functional. ● Comes with a sensor protection cap.

It is ideal for confirming biological and chemical coloration, such as with biosensors. You can drop liquid onto the filter of a disposable chip and then check for subsequent coloration and decoloration. The coloration is confirmed by reading the reflected light using a tricolor photodiode.

●Switching function between dry batteries and external power supply (AC adapter: optional).

1. Replacement of the light-receiving part, measurement of three wavelength ranges (center wavelengths 254nm, 365nm, 405nm) and temperature. 2. Measurement of illuminance, peak illuminance, integrated light quantity, illuminance distribution, illuminance of spot light, and temperature distribution. 3. Illuminance distribution measurement for up to 4 minutes with built-in memory.

The "MI1-4-IN-1R" is a multifunctional environmental measuring device that can be used as a sound level meter, illuminance meter, thermometer, and hygrometer all in one unit. It is easy to handle and very simple to operate. The large digital display makes the measurement values very easy to read.

The environmental data logger MI1V-764R is a pocket-sized environmental measuring device that can be used as a light meter, ultraviolet intensity meter, thermometer, hygrometer, and dew point thermometer all in one. With its data logger function, which has a memory of 10,900, you can set the measurement intervals to 10 seconds, 1 minute, 10 minutes, or 1 hour, allowing you to monitor light intensity, ultraviolet, temperature, and humidity over a long period, and download that data to a computer using the infrared port.

Unnoticed, excessive UV exposure is a major enemy to your skin. Let's measure it regularly and take UV care.

The radiation balance meter MC8P-NET07D measures radiation balance in the near ultraviolet and far infrared wavelength ranges. The upper surface of the radiation balance meter detects solar radiation and long-wave radiation from the sky (clouds), while the lower surface detects solar radiation reflected from the ground (albedo) and long-wave radiation from the Earth, measuring the difference as the radiation balance.

UV Ink Curing Compatible, Thin Measurement Device Check for Degradation of Exposure Lamps for Resin Relief/Flexo CTP ● Wide UV Measurement Range - This product is a device used to measure the UV intensity of UV lamps used in printing machines. - It measures UV intensity in the range of 260nm to 400nm. ● Ultra-Thin Sensor - The sensor probe is separate, and the thickness of the sensor part is 2.8mm, allowing it to be inserted and measured through narrow openings in printing machines.

The sensor has spectral sensitivity characteristics equivalent to the human eye (visual sensitivity).

This measuring device is a UV illuminance and light meter developed for various infrared exposure machines, UV dryers, and general UV measurements. Its slim and cordless design allows for measurements in locations that were difficult to measure with conventional devices. The measurement range can be widely covered from low to high illuminance by using the included filters. Its compact size makes it easy to carry anywhere, fitting conveniently in your pocket.

This device is the world's first gloss meter (60°) that can be used not only on very small surface areas but also on curved surfaces. It can be used for checking the finish of curved surfaces in industries such as aerospace parts, automotive bodies, household goods, ceramics, and plastics, as well as for micro-surface checks in printing, photography, textiles, and more. A very thin light beam that reflects from areas as small as 2×2mm is utilized, allowing for the examination of the uniformity of finishes from a series of surface measurements.

It has a built-in rechargeable battery and an automatic power-off mechanism (20 seconds). The memory capacity, supported by the built-in lithium battery, can retain approximately 4000 data points for 5 years.

A spectrophotometer that demonstrates on-site capabilities for color measurement. It achieves unprecedented ease of measurement and simple operation through a color LCD display. ● Compact and easy to hold - Small and lightweight. - Vertical grip that is easy to hold and provides good stability. - High mobility in production environments. ● Suitable for any measurement location.

●It features a peak hold function that displays the peak value during measurement. ●The unit of Lx/fc can be switched with a single touch.

● Measuring brightness in offices and workspaces to maintain eye health. ● Maintaining and managing optimal environments for crop growth. ● Easy-to-read large screen LCD. ● ×1, ×10, ×100 wide range measurement.

This is an illuminance measuring instrument that measures the brightness of offices and workspaces, making it ideal for improving workplace environments.

We measure the irradiance and radiation amount per hour for testing or maintenance of thermal equipment such as solar power generation and solar cells.

The digital long-wavelength ultraviolet intensity meter is a UV measuring device that measures long-wavelength A waves in the spectrum range of 320 to 390 nm, centered around 365 nm.

It comes with a data hold function that fixes the displayed value.

■Specifications ●Accuracy: ±5% rdg ●Functions: Hold, Max/Min display, Backlight, Bar graph display ●Memory: Automatic / 16,000 continuous data, Manual / 99 data ●Interface: USB

■Specifications ●Accuracy: ±100W/m2 or ±5% ●Sampling: Approximately 0.25 seconds ●Functions: Data hold, maximum/minimum value, overload display, auto power off

■Specifications ●Accuracy: ±10W/m² or ±5% ●Sampling: Approximately 0.25 seconds ●Functions: Data hold, maximum/minimum values, auto power off ●Power supply: 006P (9V) battery x 1 (included for testing) ●Measurement range: 2000 (W/m²)

This is a measuring device that expresses the amount of chlorophyll contained in plant leaves as SPAD values, which is necessary for understanding the health of plants. The chlorophyll meter can measure instantly on-site without the need for sample collection, and it is designed to be splash-proof, allowing measurements even in the rain. ● Trend graphs can be displayed. ● It is handy and convenient to carry. ● It has a splash-proof design that allows measurements in the rain. ● It is energy-efficient.

Adoption of silicon photodiodes in the sensor.

It is equipped with a hold function to fix the display, a MAX hold function, and an auto power-off function.

The MI1TT-889M, which has a built-in data logger function, can store illuminance data with date and time for up to 16,000 entries and allows you to download measurement data to a computer. You can start and stop the data logger measurements up to 99 times, and save them as different data files. The measurement data is saved in a dedicated file format as well as in text file format, making it possible to view the data in Excel. Additionally, with the MI1TT-889M, you can press the memory key on the device to store the current illuminance data along with the date and time for up to 99 entries. Not only can the data be downloaded to a computer, but you can also view the illuminance value data along with the date and time by pressing the key on the device.

The MI1T-139M is a low-cost digital illuminance meter that supports a wide range of illuminance measurements from 0 to 400,000 Lux / 50,000 foot-candles (fc) with automatic range switching. It displays illuminance in both numerical and bar graph formats. The MI1T-139M automatically compensates for differences in light sources, allowing for illuminance measurements with any type of light source, including tungsten bulbs, fluorescent lights, mercury lamps, and sodium lamps.

● A compact type that fits in the palm of your hand. It is battery-operated, allowing for easy portability. ● Comes standard with easy and convenient PC software.

- Various measurement modes. (Data hold, MAX, MIN display) - Convenient for measurements in dark places with backlight. - Equipped with SD card (1-16GB) data logger function - Recording interval can be set from 1 to 3600 seconds - Compatible with USB/RS-232C interface

- Various measurement modes. (Data hold, MAX, MIN display) - Convenient for measurements in dark places with backlight. - Equipped with SD card (1-16GB) data logger function - Recording interval can be set from 1 to 3600 seconds - Compatible with USB/RS-232C interface

This is a high-precision spectrophotocolorimeter that can measure the wavelength range of 380nm to 780nm with an output interval of 5nm for reflection and transmission samples. For reflection samples, simultaneous measurement including (SCI) or excluding (SCE) the specular reflection component is possible, and measurement of samples containing fluorescence can also be performed by applying a UV cut filter. For transmission samples, a wide sample chamber with a sliding door design allows for easy measurement of large samples. It is ideal for color management of materials such as resin, glass, liquid crystal components, and metallic surfaces.

The MI1T-2418M is a solar power meter that can measure solar radiation intensity up to 1999 W/m² with range switching.

The MI1M-317M, used to measure solar radiation intensity, is a solar power meter that can measure solar radiation intensity up to 1999 W/m² with range switching.

The MI1M-318M, used to measure solar radiation intensity, is a solar power meter that can measure solar radiation intensity up to 1999 W/m² with range switching.

The MI1A-2128M is a new type of solar power meter with added multimeter functionality. It allows for the measurement of solar irradiance while simultaneously measuring voltage and current with a multimeter, making it easy to evaluate solar panels.

An all-in-one colorimeter that integrates all functions such as display and operation buttons. It eliminates the need for cumbersome computer operations, allowing anyone to easily and accurately perform measurements with groundbreaking usability. Simply turn on the power switch, place the sample, and press the measurement button. With just these few steps, anyone can quickly and easily take measurements. Additionally, the measured data can store up to 4,000 colors, and color difference reference data can be saved for up to 1,000 colors, with smooth retrieval. ● Large color LCD that supports kanji A large 5.7-inch color LCD display comparable to a car navigation monitor. The colorful graphic display achieves instrument-like visibility and usability. The color LCD display can be set to one of seven languages: Japanese, English, German, French, Spanish, Italian, and Chinese, making it easy to align with overseas offices and clients. In particular, the Japanese language is displayed in kanji, providing unprecedented visibility when combined with the color LCD.