ツール・テック東北 List of Products and Services

In line with the recent trends in PFAS regulations, our company has begun handling "Non-PFAS coatings" that do not use fluoropolymer resins. These coatings are currently being applied overseas to baking molds and pan trays, serving as PFAS alternatives that do not utilize fluoropolymer resins. Compared to traditional fluoropolymer resins, this ceramic-based coating operates at a lower processing temperature, resulting in less thermal damage to the substrate during treatment and promising a longer lifespan. Additionally, while the hardness is reduced compared to standard ceramic coatings, the film's conformability is comparable to that of fluoropolymer coatings.

• Food Processing Equipment
• Other food machinery
• Frozen dessert manufacturing equipment

Screw calibration tools and molding dies can maintain the best conditions for plastic molding. Additionally, when combined with nitriding, adhesion strength increases, potentially extending the lifespan even further.

• Injection Molding Machine
• Plastic Mould
• Resin mold

CTX is a coating with high hardness, low wear, and excellent anti-seizing properties. It has a silver TiCN with high hardness on the surface, and through multilayering, it controls internal stress, resulting in a highly reliable coating with excellent resistance to peeling and chipping.

• End Mills
• Mold Design
• Press Dies

The "IRIS-CA1" is a treatment proposed for extending the lifespan of press molds (punches and dies) used for processing Colson materials, which have been struggling with shot counts under harsh conditions in the previous "DLC-IRIS." Due to special conditions, AlCrN can be deposited in a smooth state with surface roughness similar to that of "DLC-IRIS." With a film thickness of 1μm, we have made it possible to deposit AlCrN with a smooth surface roughness, resulting in good adherence to precision parts. (In actual measurements, processing on a mirror test piece with Ra0.011 resulted in Ra0.017.) 【Features】 ■ Measures to extend the lifespan of press molds (punches and dies) for processing Colson materials that have been struggling with shot counts ■ AlCrN can be deposited in a smooth state with surface roughness similar to DLC-IRIS due to special conditions ■ Enables deposition of AlCrN with a smooth surface roughness at a film thickness of 1μm ■ Good adherence to precision parts *For more details, please refer to the PDF document or feel free to contact us.

• Other surface treatment equipment
• Surface treatment contract service

The high hardness and ultra-thin film DLC-Iris "Iris Coating" is a treatment that has been widely used in various applications, such as extending the lifespan of press molds (punches and dies) that previously experienced peeling with conventional DLC, as well as in resin molding molds (gas corrosion, release, wear resistance) and connector manufacturing companies. It can also address issues related to adhesion in non-ferrous cutting and pressing, and is suitable for parts that require strict thickness and surface roughness management. For more details, please contact us or download the catalog.

• Other surface treatment equipment
• Surface treatment contract service

It is effective against adhesion of substances such as paste, adhesives, molten plastics, rubber, and plating solutions. We offer a fluorine-based Type F and a silicone-based Type S, so we can provide suggestions tailored to your application. If heat resistance is required, we also have a high-temperature type available (heat resistance up to 345°C).

• Processing Contract

Diamond chip saws used for standard cutting of substrates At Tool Tech Tohoku, we manufacture products according to your specifications, from standard sizes of cutting machine manufacturers to custom specifications. In particular, the settings for blade thickness, number of teeth, and grinding precision are crucial depending on the dimensions of the substrate (number of layers) and cutting conditions. *For details such as outer diameter, blade thickness, and number of teeth, please contact us.

• Other cutting tools
• Diamond cutter

With an appropriate surface roughness and slip properties, it is effective for transporting small resin products. It has better slip properties than conventional fluoropolymer coatings, and the film hardness is 9H, which is about three times harder than fluoropolymer coatings. *For more details, please feel free to contact us.*

• Parts feeder
• Assembly Jig
• Food Processing Equipment

The "S-V Coat," a film that improves sliding properties, targets areas where DLC (diamond-like carbon) has not been able to provide adequate sliding performance until now. We propose this film as an alternative to DLC for components in environments where continuous repeat use has been difficult due to issues with peeling and heat resistance, while you have been using DLC for the purpose of improving sliding properties. 【Features】 ■ Reduction of friction due to special surface shape effects ■ Improved sliding properties for solid materials such as glass, non-ferrous metals, and plastics ■ Excellent wear resistance with a film hardness of HV3000-3500 ■ Durability surpassing conventional non-stick coatings and DLC ■ Excellent oxidation resistance characteristics ■ Oxidation start temperature of 1100°C, suitable for environments where DLC could not be used

• Other surface treatment equipment

The non-stick coating "OH-Si Coat," which combines release properties and water repellency comparable to fluoropolymer (Teflon coating), has been born. It is a new non-stick coating that offers superior durability and high adhesion compared to the conventional OH-F Coat. Please feel free to consult us.

• Sealing machine
• Plastic Mould
• Resin mold

Many factories can process DLC, but in our case, we can always handle the latest DLC, so we are well-received in terms of price, delivery time, and quality by customers currently using DLC. We also handle various surface treatments, so please feel free to consult us. - Water-repellent DLC - Heat-resistant DLC - DLC suitable for oil and water - Conductive DLC - High insulation DLC - DLC for lens molds - High adhesion DLC

• Surface treatment contract service

A non-stick coating has been developed that combines release properties and water repellency comparable to fluoropolymer processing (polytetrafluoroethylene resin). It is effective against adhesion of adhesives, glues, and molten plastics.

• Bag making machine/slitter
• Plastic Mould
• Surface treatment contract service

W-B-in is a ternary alloy coating composed of Ni (Nickel: 94%), B (Boron: 1%), and W (Tungsten: 5%). The coating hardness is very high at approximately 800 Hv in the precipitated state, and it excels in heat resistance, corrosion resistance, and wear resistance, as well as having good release properties, making it suitable for use in molds for resin molding. It has a glossy finish and is an electroless plating, allowing for the maintenance of dimensional accuracy. For more details, please contact us or refer to the catalog.

• Surface treatment contract service

P-in Teflon electroless nickel is a composite plating that co-deposits PTFE (polytetrafluoroethylene) within the electroless nickel coating. Due to the properties of PTFE, characteristics such as water repellency, release properties, and slip properties are enhanced, making it suitable for products such as sliding parts and molds that require release properties. Compared to Teflon electroless nickel, P-in has a higher coating hardness, providing excellent wear resistance and other superior characteristics. For more details, please contact us or refer to the catalog.

• Surface treatment contract service

ICF film (Intrinsic Carbon Film) is a general term for carbon films that possess high functionality and multifunctionality, including DLC. ICF films are amorphous (non-crystalline) carbon films that are positioned between graphite and diamond in structure. The film surface is smooth, has a low friction coefficient (μ = 0.1), and exhibits self-lubricating properties, which helps prevent metal adhesion to molds during the forming of soft metals and protects the mirror surface of the molds. ICF films aim to replace oil, promoting oil-free and maintenance-free applications. For more details, please contact us or refer to the catalog.

• Surface treatment contract service

Mercury Coat W is a new coating that excels in high hardness, oxidation resistance, and wear resistance. We have developed a coating that demonstrates excellent performance under cutting conditions suitable for dry processing, high-speed machining, and high feed rates, which are being advanced in the field of tooth cutting. It is compatible with a wide range of workpiece materials (20 to 60 HRC) and can be used for both wet and dry machining. It has excellent lubricity, good chip evacuation, and exhibits outstanding cutting performance even in high-speed cutting. For more details, please contact us or refer to the catalog.

• Surface treatment contract service

"Venus Coat" is a revolutionary coating that offers heat resistance of over 1,100°C and a film hardness of HV 3,500, significantly enhancing the durability of molds. It is ideal for aluminum die-casting molds and cold/hot forging mold components. 【Features】 - Heat and oxidation resistance at over 1,100°C - Improved film lifespan at high temperatures - Significantly enhanced wear resistance due to film hardness of over HV 3,500 - Applicable to mold fields requiring heat oxidation resistance and high hardness Please try the effects of improved release properties and low friction from the lubrication-enhancing coating at high temperatures. *For more details, please contact us or download the catalog.

• Other surface treatment equipment

The QLIMAQ LELLYON series enhances heat crack resistance by incorporating an intermediate layer and reduces pinholes through its multilayer structure. As a result, it exhibits superior wear resistance compared to the current TiAlN and CrN coatings. Additionally, there is a new coating called LELLYON-BZ, which is more resistant to heat and wear than CL and ATL. *For more details, please contact us or download the catalog.

• Other surface treatment equipment

Kanak processing is a surface hardening treatment method that can significantly improve the lifespan of molds by increasing the surface hardness of SUS (stainless steel) and SKD (alloy steel) to levels comparable to that of cemented carbide. It does not generate a white layer (iron nitride), and it can produce a uniform hardened layer even in complex shapes and deep holes. It is suitable for hardening treatment of stainless steel, with extremely minimal deformation due to warping, expansion, and dimensional changes. The depth of the diffusion layer can also be controlled. The surface roughness after treatment is very low, and there is no observed decrease in toughness due to repeated treatments, allowing for welding operations to be performed without issues after treatment. Furthermore, composite treatments such as PVD coating are possible. *For more details, please contact us or download the catalog.

• Surface treatment contract service

By innovating the coating conditions, a surface treatment has been created that imparts water-repellent properties similar to fluororesin to DLC coatings. ■□■Features■□■ ■DLC coating with hardness equivalent to carbide (HV 1,000) and low friction coefficient (μ = 0.04 to 0.17). ■Due to its darker color compared to standard DLC products, it can be used for anti-reflective applications (wear resistance + thin film + black coating). ■Prevents mold contamination and contributes to improved productivity. ■Special specifications are available to enhance surface pressure against impacts in the vertical direction, which was a weakness of DLC. ■Applicable materials: carbide, SKH, SKD, SUJ2, SUS, ceramics, aluminum. ■Coating size: φ300 × 200 mm. ■Film thickness settings: standard 1 to 2 μm; ultra-thin films of 0.1 μm are also available. ■If you have experienced peeling with conventional DLC, please give it a try. For more details, please contact us.

• Surface treatment contract service

Features: Uses ultra-fine particle super-hard material. No need for bushing in center drill processing. Excellent chip removal, and no need for reaming. Shape dimensions: No oil hole: Regular shape, With oil hole: Regular, Medium, Long shapes. Tip angle: 140° Shank: h6 Diameter: m7

• Other cutting tools
• drill

Precision mold components, various surface treatments, special cutting tools, and chemical products sales comprehensive trading company. This is an introduction to "Precision Mold Components - Mobile Die" handled by Tool Tech Tohoku. ■□■Features■□■ ■ Achieves dimensional tolerance of ±0.02 through the introduction of high-precision machining centers. ■ By using stainless steel with hardness equivalent to Thomson blades (Vick blades), durability is dramatically improved. ■ By applying laser cutting technology to minimize the processing area, processing time is significantly reduced. ■ Combined with Bakelite, the total height is 23.6 mm, allowing use without changing the settings of the press machine. ■ Can also be incorporated into Thomson molds. ■ Accuracy: ±0.02 mm or less. ■ Delivery time: From 1 day. ■ Minimum blade spacing: 0.3 mm or more. ■ Minimum R: R0.1 (right-angle processing is also possible). ■ Maximum processing size: 200 × 140 (mm). ■ For more details, please contact us.

• Other machine elements
• Contract manufacturing
• Processing Contract

Precision mold components, various surface treatments, special cutting tools, and chemical product sales comprehensive trading company. This is an introduction to 'Precision Mold Components - Titanium Die' handled by Tool Tech Tohoku. ■□■Features■□■ ■High precision and high-precision processing enable the handling of very fine shapes. ■Made from titanium alloy machined by NC processing, suitable for very fine shapes, capable of processing with a blade gap distance of 0.3 mm or more. *Note: There may be cases where it cannot be accommodated depending on the thickness of the workpiece. ■By incorporating it into a Thomson die, it can accommodate molds that are difficult to manufacture with strict precision. ■Precision: ±0.05 mm or more. ■Delivery time: 2 days or more. ■The shape has round holes of approximately φ4.5 and φ1.0 within a square of about 7 mm, but by making it a progressive die, issues with ejection are resolved. ■Circular scrap removal can also be made more efficient by performing side punch processing. ■For more details, please contact us.

• Other machine elements
• Contract manufacturing
• Processing Contract

Tool Tech Tohoku's unique organic nano-thin film treatment technology "NANOS" enables the modification of surface properties of various materials such as metals, glass, and resins by forming ultra-thin functional films on their surfaces at the nanoscale, imparting functions such as water repellency, oil repellency, release, and dirt resistance. ■□■Features■□■ ■ Possesses functions such as water repellency, oil repellency, release, and dirt resistance (contact angle with water is 110-120°) ■ Capable of film formation on all materials including metals, glass, and resins (for resins, an adhesion layer can be inserted as needed) ■ The film thickness is extremely thin, ranging from a few nanometers to several hundred nanometers, and the low processing temperature has little impact on dimensional changes or damage to the substrate ■ Sales of the dedicated processing equipment for the "NANOS" process, the "Desktop NANOSCEPTER," have begun * Raw materials are also sold by Tool Tech Tohoku, with thin film specifications "NANOS B" (film thickness: 10 nm, 20 nm) ■ The newly developed material "NANOS Y" offers improved heat resistance and water repellency ■ For more details, please contact us.

• Surface treatment contract service

We are offering diamond throwaway tips at a low price. For standard products, we will inform you of the discount rate. For custom products, please let us know whether you will provide carbide tips and supply the drawings. We offer prices that will satisfy end users and trading companies that handle large quantities, so please inquire about the prices. All CBN tips are custom-made. If you would like to discuss various coatings, feel free to consult with us. Range of diamond tips: standard stock items to custom-made products and regrinding. *For standard stock items, we will send you a catalog, so please feel free to inquire. Due to popular demand, we are offering special prices. (We also provide to companies in the machine tool industry.)

• Other cutting tools

Precision mold parts, various surface treatments, special cutting tools, and chemical products sales comprehensive trading company. This is an introduction to "Precision Mold Parts Pinnacle Die and NEW Pinnacle Die" handled by Tool Tech Tohoku. ■□■Features■□■ ■ The conventional corrosion blade (etching blade) is processed with sharpening, creating a sharp edge by CNC sharpening that forms an acute blade tip. ■ It is now possible to cut materials such as paper and film that could not be cut with conventional etching blades, and it can sufficiently meet the high precision requirements for FPC substrates. ■ The blade height can be adjusted according to the thickness of the product being cut. ■ Precision: ±0.05 mm or better. ■ Delivery time: 4 days (Pinnacle), 5 days (Hard Pinnacle), 6 days (NEW Pinnacle), 7 days (Hard NEW Pinnacle). ■ If adhesion is particularly concerning, applying a Toshi-cal coating will allow for smooth processing of high-adhesion sheets (consultation required). For details, please contact us.

• Other machine elements
• Contract manufacturing
• Processing Contract

Minimal scattering from high-speed rotating chains, maintaining long-term lubrication "High-grade heat-resistant lubricant, high concentration" Ideal product for motorcycles, bicycles, racing cars, chains, blocks, and chainsaws, suitable for sliding and rotating parts of bicycles. *For more details, please contact us.

• Lubricants

**Application** It is also effective for insulation. DLC coating is currently used in many applications and has shown effectiveness, but there were concerns about adhesion under high loads due to its high hardness and low-temperature treatment. DLC-soft was developed to address this issue by significantly improving the adhesion of the coating by lowering its hardness to an acceptable range. This coating has been spreading mainly in Europe and the United States and is being applied to sliding and rolling parts that experience high loads, such as automotive components and fuel injection pump parts.

• Surface treatment contract service

Point 1: Achieved high-speed cutting of HRC 60 or higher, which was previously impossible. Point 2: Capable of processing high-hardness materials efficiently, contributing to reduced machining costs. Point 3: Exhibits outstanding performance in dry machining due to heat-resistant oxidation properties above 1100°C. Point 4: Excellent heat-resistant oxidation properties significantly extend cutting performance at high temperatures compared to conventional coatings. Point 5: Applicable in the mold industry where high heat-resistant oxidation properties are required. *For more details, please contact us or download the catalog.

• Surface treatment contract service

Point 1: Significantly improves lubrication without compromising heat resistance and wear resistance. Point 2: Demonstrates high performance in the machining of a wide range of materials with HRC 20 to 50. Point 3: High lubrication reduces chip adhesion and facilitates chip removal. Point 4: High heat resistance allows for applications in dry machining and mold fields. *For more details, please contact us or download the catalog.

• Surface treatment contract service

If a blade from a competitor's diamond saw chips, it will quickly lose its cutting ability, but our company's diamond saw maintains its cutting performance even with minor chipping due to the characteristics of its blade design, preventing side burrs and fraying. Moreover, it operates quietly. Prices vary depending on standard dimensions and the number of teeth, so please feel free to consult us.

• Plastic processing machines (cutting and rolling)

If you're looking for affordable chemical products, leave it to us. Feel free to consult us even if it's just for a quote.

• Fine Ceramics
• Cleaning agents
• others

Toshical S UNA-800 Series The coating structure is broadly divided into two layers. The first layer is coated with a special metal in a textured shape, and the second layer is coated with a special resin made from a polymer copolymer, leaving the textured shape intact. Conveying Roll: Used in packaging machines that utilize PE-based adhesive films (sheets). Even thin adhesive films can be transported reliably without scratching and do not cause adhesion issues. Toshical S UNA-300 Series This technology was developed to address cases where the textured structure obtained from the UNA-800 series becomes a disadvantage. It directly forms a textured shape on the target substrate and is coated with a non-adhesive copolymer resin. The degree of texture is managed by surface roughness values and can be controlled to be either smooth or textured. Hot Melt Mold: Hot melt molds for electronic component connectors. Provides excellent non-adhesiveness when hot melt is used as the molding material.

• Rubber Processing Machine
• Other surface treatment equipment
• Surface treatment contract service

Aluminum die-cast mold and cold/hot forging mold parts suitable coating 'Venus Coat' ■□■Features■□■ ■Ultra oxidation resistance and high hardness It has heat resistance over 1,100°C and a coating hardness of HV 3,500, making it a groundbreaking coating that dramatically improves the durability of molds. ■Improved film lifespan at high temperatures due to heat resistance and oxidation resistance over 1,100°C ■Significantly enhanced wear resistance due to film hardness of HV 3,500 or higher ■Applicable to mold fields where heat oxidation resistance and high hardness are required ■Ideal for parts that need to maintain sliding properties and wear resistance at high temperatures ■If the focus is on galling and seizure rather than melting or wear resistance, we will propose a different type of coating. For details, please contact us.

• Surface treatment contract service

Precision mold components, various surface treatments, special cutting tools, and chemical product sales comprehensive trading company. This is an introduction to the "Precision Mold Component Frame Die" handled by Tool Tech Tohoku. By combining high-speed, high-precision machining centers with laser cutting machines, we achieve high precision, high hardness, and short delivery times for dies! ■□■ Features ■□■ ■ High Precision - The high-speed, high-precision machining center makes it possible to achieve blade sharpening that was previously impossible, maintaining stable cutting edge accuracy. ■ High Hardness - By using high-speed machining centers, the range of material selection expands, allowing processing of stainless steel with hardness equivalent to Thomson blades (around HRC 53), thereby improving the durability of the mold. ■ Short Delivery Time - The material itself has already undergone special treatment, eliminating the need for heat treatment after processing. - Laser processing is used for cutting prior processes except for necessary lines. - Ring processing is only done where necessary. ■ For more details, please contact us.

• Other machine elements
• Contract manufacturing
• Processing Contract

We are pleased to introduce our "Precision Mold Parts, Precision Tools, and Precision Machine Parts," which have received high praise from semiconductor manufacturers and electronic component manufacturers. ■□■Features■□■ ■ We can respond to ultra-high precision mold parts with short delivery times. ■ We also offer a set sale of precision mold parts + surface treatment. ■ We specialize in machine parts and jigs made from cemented carbide materials. * For example... cemented carbide sleeves (with ultra-fine holes of 0.3 mm). ■ We can handle precision parts made from various materials such as cemented carbide, ceramics, high-speed steel, and die steel. ■ Advantages of manufacturing + surface treatment outsourcing: - Avoiding issues such as tempering temperature problems. - Reducing shipping costs by double or triple. - Quality assurance through consistency. ■ We excel in producing parts that require special techniques and are not easily manufactured by others. For more details, please contact us.

• Other cutting tools
• Contract manufacturing
• Processing Contract

Air Conditioning Cleaning Services for Factories, Offices, and Stores ■ Are you experiencing any of these symptoms with your current air conditioner? - A musty smell - Weak heating and cooling capacity - Water splashing - Condensation at the air outlet The cause is fine dust that cannot be removed by the filter. This dust adheres to the air conditioner's heat exchanger, leading to a significant increase in power consumption and various malfunctions, as well as symptoms such as mold, unpleasant odors, water leaks, and clogs in the hose that sends water outside. Regular cleaning helps prolong the life of the air conditioner and can also lead to savings on electricity bills. Tool Tech Tohoku's air conditioning cleaning proposal focuses on extending the lifespan of air conditioners to prevent future breakdowns and replacements, as well as reducing electricity costs for air conditioners that are used for long periods in factories, allowing for long-term cost savings through cleaning. For more details, please feel free to contact us.

• Other cleaning machines
• air conditioning
• Other services

The highest measurement accuracy achieved for evaluating various materials and thin films at the nano level Tool Tech Tohoku Co., Ltd. "Contract Analysis and SEM Observation" ■□■Features■□■ ■nano Hardness Tester ... Hardness and Young's Modulus - Displacement resolution: 0.03nm Load resolution: 1μm - Sapphire ring system to suppress thermal drift effects - Surface observation using a microscope and AFM ■Scratch Tester ... Adhesion Strength - Measurement of adhesion strength for thin films ranging from 10nm to 20μm - Observation of scratch marks using a microscope - Measurement on curved surfaces possible with feedback mechanism ■Tribometer ... Friction and Wear - Load: 50μN to 1N (NTR) 1N to 20N (TRB, HTT) - Rotational and reciprocating friction (only NTR) possible - Stress analysis simulation function for ball and substrate ■Calotest, AFM, NST ... Film Thickness and Surface Shape - Measurement of film thickness for multilayer films - Various analyses possible with analysis software - Measurement of shape and wear amount using nano Scratch Tester (NST) ■For more details, please contact us.

• Contract measurement
• others

Precision mold parts, various surface treatments, special cutting tools, and chemical product sales comprehensive trading company Tool Tech Tohoku Co., Ltd. We would like to introduce our "PVD/CVD Coating (Heat-resistant Prime Coat - T)." With a rich selection of coating films, we extend the lifespan of various molds, jigs, and cutting tools, achieving a reduction in total costs. Our integrated processing from main body machining to coating allows for rapid response. We offer various treatment methods, including CVD coating at temperatures close to 1,000°C, PVD coating that can form films at around 500°C, and low-temperature PVD that works with any material below 250°C. Please feel free to consult us about any requirements you may have.

• Surface treatment contract service

Stable adhesion! PBS (Plasma Booster Sputtering) Process Dry coating as an alternative to chrome plating ■□■Features■□■ ■Stable adhesion with low-temperature treatment - Capable of low-temperature treatment below 250°C, allowing processing of SCM carburized steel, SKS, SUJ, etc., while minimizing the reduction in base material hardness. - Achieves consistently excellent adhesion strength. ■High-precision coating is possible - Based on sputtering technology proven in semiconductor processes, using large targets for superior film thickness accuracy and reproducibility. - Applicable to precision parts and molds with strict tolerances. ■No droplets and smooth surface - No droplets like those from arc IP, resulting in a uniformly smooth surface with low surface roughness. - Low aggressiveness towards counterpart materials in sliding parts and precision molds, resulting in good tribology. ■For more details, please contact us.

• Surface treatment contract service

The surface of the film is smooth, with a low friction coefficient (μ = 0.1), and has self-lubricating properties, which prevents metal adhesion to molds and protects the mirror surface of molds during the forming of soft metals. 'ICF Coating - High-Functionality and High-Performance Carbon Film' ■□■ Features ■□■ ■ The ICF film is an amorphous (non-crystalline) carbon film, positioned between graphite and diamond structures. * The ICF film (Intrinsic Carbon Film) is a general term for carbon films with high functionality and multifunctionality, including DLC. ■ The ICF film serves as a substitute for oil, achieving oil-free operation and maintenance-free performance. ■ Due to its amorphous structure, it lacks grain boundaries, resulting in a very smooth surface compared to hard thin films with polycrystalline structures, such as titanium nitride. ■ Hardness: 2,000 - 2,200 HV ■ Friction coefficient: μ = 0.1 ■ Film thickness: Standard 1 μm; ultra-thin films of less than 0.1 μm are also available. ■ Applicable materials: Cemented carbide, SKH, SKD, SUJ2, aluminum alloys, beryllium copper, etc.

• Surface treatment contract service

Fluororesin Coating "Nidax, Nifgrip, Toughram" ■ Hard and Smooth Surface - Nidax - A surface treatment based on a nickel coating for iron, stainless steel, and copper alloys, where fluororesin is impregnated into the deposited nickel coating and then heat-treated. - It features high hardness, excellent wear resistance, slip properties, galling prevention, and non-stick properties, along with superior adhesion to the material, making it a high-performance composite treatment. ■ Surface Rich in Release Properties - Nifgrip - A surface treatment for iron, stainless steel, and copper alloys, where nickel and fluororesin are co-precipitated and then heat-treated. - The coating has 10% and 30% fluororesin uniformly distributed by volume, allowing the performance of the fluororesin to be fully realized, particularly excelling in non-stick properties, providing sufficient effects for release and slip properties, resulting in a high-performance composite film. ■ Smooth and Hard Surface - Toughram - An ideal treatment for surface processing of aluminum and aluminum alloys. - It excels in wear resistance, slip properties, corrosion resistance, seawater resistance, release properties, and electrical insulation, achieving a high-performance composite film integrated with the base material through surface treatment technology. - It is applied in a wide range of fields and used in many products and components.

• Processing Contract

Exhibiting excellent performance for more stringent corrosion resistance measures! PVD-Ion Plating Method 'ACC-ACT' ■□■Features■□■ ■Excellent coating characteristics and adhesion, processing at temperatures suitable for the treated material across a wide temperature range. ■Deformation and alteration of the treated material due to heat are extremely minimal; <ACT> excels in wear resistance and oxidation resistance, while <ACC> is particularly outstanding in corrosion resistance, demonstrating exceptional performance in even harsher corrosive environments. ■Coating that excels under more stringent corrosion conditions. ■Significantly suppresses the occurrence of pitting corrosion. ■Also suitable for cavitation and erosion resistance measures. ■If you are currently using CrN, please consider this once. For details, please contact us.

• Surface treatment contract service

Precision mold parts, various surface treatments, special cutting tools, and chemical product sales comprehensive trading company. This is an introduction to 'Precision Mold Parts - Thomson Type (Bik Type)' handled by Tool Tech Tohoku. Currently, efficiency has improved with the introduction of bending machines, but for important processes that affect the quality of the mold, such as adjusting the bending degree and processing the blade-to-blade joints, skilled craftsmanship is required. ■□■Features■□■ ■Wide range of applications from general cardboard, seals, and automotive interiors to FPC substrates ■Embedding SK material blades processed into plywood ■Precision ±0.1 mm or better ■Delivery time 2 to 3 days ■If you are concerned about adhesion to the Bik blade, applying Toshi Cal coating will allow for smooth processing of strong adhesive sheets. (Meeting required) For details, please contact us.

• Other machine elements
• Contract manufacturing
• Processing Contract

Precision mold parts, various surface treatments, special cutting tools, and chemical product sales comprehensive trading company. This is an introduction to the 'carbide tipped saw blades, cutters, routers, and dowel drills' handled by Tool Tech Tohoku. We offer a wide variety of products from standard items to custom-made ones. We have achieved a remarkable improvement in durability by using high-hardness class carbide K01 (ISO standard), which has traditionally been considered difficult to use. The appearance and shape are the same as conventional carbide brazed type tools. Additionally, re-sharpening can be easily done using traditional methods. The durability is 2 to 3 times that of conventional carbide brazed type tools. For example, even if you replace a conventional cutter 6P with a KC cutter 4P, you will have more than double the durability. It is ideal for wear of cutting edges due to plywood adhesive layers like LVL, wear from MDF and boards, and recycling (regeneration) of tools. - We will remake the base of tools that can no longer be sharpened to restore them to like-new condition. - The cost is approximately 80% of that of new production, so please give it a try. *For more details, please contact us.

• Other cutting tools