disk Product List and Ranking from 52 Manufacturers, Suppliers and Companies

0584 Shortening the discharge time from the silo

A total of 24 units can be installed on 4 sides! We can provide suitable implementation proposals that meet the user's requirements.

We would like to introduce a case where "Blow Disk" was implemented to shorten the discharge time from the dust collection silo. The equipment flow is dust collector → silo → jet pack truck, and due to poor dust flow, loading onto the jet pack truck took a long time, which was the objective of this improvement. We installed a total of 24 units, with 1 unit on the bottom tier, 2 units on the middle tier, and 3 units on the top tier, on each of the 4 sides, close to the discharge section. Our company can provide suitable implementation proposals tailored to the user's conditions. 【Condition Overview】 ■ Silo dimensions: approximately 2500×2500 ■ Discharge diameter: 300A ■ Contents: dust collection dust 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign matter contamination. The silicone disks of this equipment are exceptionally strong and durable. We believe you will understand this once you use it! ■ Control (how to aerate?) is crucial! Our company provides guidance on what should be done. We also have a dedicated controller prepared.

Company：ミナギ
Price：Other

Vibration motor
Other processing machines
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

At the hopper for supplying wallpaper crushing products.

The subject is the powder of crushed wallpaper! Here is an example of installing a blow disk at the bridge generation point.

Although there is an agitator in the hopper to prevent bridging, we have improved the issue of bridging occurring in areas that it cannot reach. The process for implementation began with reviewing the hopper diagram and contents, followed by conducting tests using four "Standard Blowing Disks." The test results were favorable, and we adopted the "Controller (C-SV1)" with one built-in solenoid valve. 【Overview】 ■ Target material: Powdered wallpaper scraps (appearance is cotton-like), bulk density is about 0.2 ■ Hopper: 800×800, 2 vertical sides, 2 inclined sides ■ Discharge device: Screw feeder ■ Mixer: Located near the center of the hopper ■ Situation: Bridging between the mixing blades and the screw feeder ■ Countermeasure: Installation of blowing disks at the bridging area mentioned above (2 disks per inclined side, totaling 4 disks) *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Other machine elements
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0591 Solving NG (compost) in hammering.

During driving, advice on air ON time and air pressure, etc.! A case that responded to an urgent matter.

We received an urgent inquiry from the customer regarding a matter. "It does not drop with hammering (therefore it is likely not suitable for a knocker)," and "based on experience, it tightens with a vibrator" were the situations described. After confirming the sample and hopper diagram, we will inform you of the recommended model, layout, and control examples. The customer has installed items such as a blow disk, and the operating results have been favorable. Based on our past experiences, we provide guidance that aligns with the customer's problem-solving needs. We have been able to assist with a high probability so please feel free to consult us. [Overview] ■ Hopper dimensions: approximately 2000×1800 ■ Discharge: transported by a lower belt conveyor ■ Target item: name undisclosed, appearance resembles compost (bulk density 0.5, moisture content 40%) *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Other machine elements
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Example of implementation in the PS crushing material hopper.

PS recycling equipment's crushing material hopper! Here we introduce an example of how this equipment solved bridging issues.

Due to the occurrence of bridging, the customer implemented modifications to the hopper cone as a countermeasure. The original hopper had a gentle slope, and the diameter of the discharge section was small considering the size of the material. Even after the modifications, bridging still occurred, leading the customer to consult us. After discussing the contents and hopper conditions, we proposed a countermeasure using a blow disk and provided a loan unit. The user conducted effectiveness verification, which yielded good results. 【Overview】 ■ Hopper Diameter: φ1800 ■ Material: Ground polystyrene 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign material contamination. The silicone disk of this equipment is highly superior in strength and durability. We believe you will understand this once you use it! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please refer to the PDF materials or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0597 Eliminate the pigment fine powder bridge in one shot.

We have solved the bridging phenomenon that occurs in the hopper of the quantitative supply screw feeder in one go!

We received a contact from a customer stating, "The air knocker and air vibrator are ineffective, so I would like to install the 'Brodisk.'" After providing guidance on the installation, the device was introduced, and the results have been very favorable, receiving high praise. In this case, the customer purchased the equipment immediately after the inquiry, but we offer free lending of our products. You can first try out the effectiveness of this device. Please feel free to take advantage of this. 【Introduction Overview】 ■ Issue: Suppression of the bridging phenomenon occurring on the screw ■ Contents: Pigment fine powder ・ABD: Approximately 0.3, angle of repose: Approximately 50°, adhesion: Yes ■ Hopper: 500×500 (2 vertical sides, 2 inclined sides) ■ Quantity: 1 unit on each inclined surface, totaling 2 units installed ■ Arrangement: The 2 units are at the same height, each offset from the center to the left and right *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Countermeasures for clogging of discharge parts due to attached growth.

After the introduction, there was no damage to the hopper, and operations are running smoothly without any extra burden on the on-site personnel!

Due to the growth of adhesion and the occurrence of blockages near the hopper discharge area, we have installed a "blow disk" as a countermeasure. Previously, issues were addressed through manual hammering, which resulted in unevenness in the impacted areas. Since the introduction of this equipment, there has been no damage to the hopper, and the on-site personnel have been able to operate smoothly without any extra burden. 【Introduction Overview】 ■ Hopper Overview - Size: 500×600 - Discharge Area: 150×200 - Inclination: Approximately 70° ■ Equipment Arrangement - A standard blow disk (BD-15) has been installed near the discharge area on each side, totaling 4 units. 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign matter contamination. The silicone disk of this equipment excels in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF materials or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0604 Due to residual resin runner crushing products

Successful results and adoption! A case of installing our product at the corners of gentle slopes and gentle slopes.

This is a case where a "Blow Disk" was installed to address the residuals of crushed resin runner powder. In a situation where it was "remaining in the corners of a gentle slope," we tried this product and found it to be effective, leading to its adoption. Additionally, we also tested the "Blow Disk Mini" as a measure against powder clogging in the cyclone, and it also yielded good results, leading to its adoption. 【Case Overview】 ■ Target Material - Crushed resin runner pellets ■ Situation - Remaining in the corners of a gentle slope ■ Equipment Arrangement - One unit on each gentle slope (total of 2 units) - Using the standard Blow Disk, positioned in the corners and adjusted in height 【Key Points of Our Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign material contamination. Our silicone disks are highly superior in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please refer to the PDF materials or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0606 Resolving poor iron powder leakage

Measures near the discharge area are important! We will provide you with a rational solution that meets your requirements.

As part of the improvement of existing systems, we received an inquiry from an engineering company and adopted the "Broad Disk." Although the fluidity of the target material is not bad, the discharge section is small at Φ50, so we focused our measures here. For detailed arrangements, please contact us. We provide rational solutions tailored to our customers' conditions. 【Case Overview】 ■ Hopper Diameter: Φ800 ■ Discharge Diameter: Φ50 ■ Target Material: Iron powder (specific gravity: approx. 3, particle size: average about 100 microns) ■ Equipment Arrangement - A total of 4 Broad Disk Minis - 4 Broad Disks 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of the risk of foreign matter contamination, as well as strength and durability. The silicone disks of this equipment are extremely excellent in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is important! We provide guidance on what should be done. We also have a dedicated controller prepared. *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0613 Elimination of potassium sulfate bridge

Air ON with the Brodisk at a time delay! Introducing a case that resolved a problem in one shot.

We received a consultation regarding a problem where a bridge occurs in the newly introduced air transport tank. The equipment flow is "air transport → dust collector → hopper → rotary valve → screw feeder," and even when poked with a stick, it only creates a hole and does not come out easily, resulting in a situation where it took a long time to finally resolve. Therefore, we installed a total of 8 Brody disks (BD-15) in 2 tiers. This completely resolved the issue. 【Case Summary】 ■ Equipment Flow: Air transport → dust collector → hopper → rotary valve → screw feeder ■ Problem Situation - Bridging in the hopper - Does not come out easily even when poked with a stick (only creates a hole) - Takes a long time to finally resolve *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0632 Resolving blockages in gypsum (products)

Measures against clogging of gypsum powder that tends to remain in the four corners! A case study of installing a brody disk.

We would like to introduce a case where "Blow Disks" were used to address issues of gypsum powder clogging and residue in the product receiving hopper. To counter problems such as blockages at the discharge section and residues that tend to accumulate in the four corners, we installed one Blow Disk on each side, 150mm above the discharge section. Additionally, by placing one Blow Disk on each side of the flat area adjacent to the upper R surface, for a total of 8 disks, we have resolved the clogging of gypsum (product). 【Case Overview】 ■Trouble Details - Blockage at the discharge section - Tendency for residues to accumulate in the four corners ■Control - Controlled by a C-SV4 controller with 4 built-in solenoid valves - Sequentially activating air for 2 Blow Disks at a time with a time delay for all 8 disks 【Key Points of This Equipment】 ■The elastic disks (silicone) are very important in terms of strength and durability, especially considering the risk of foreign material contamination. The silicone disks in this equipment are exceptionally strong and durable. Once you use them, you will understand! ■Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0634 Bridge elimination of cake-like materials

Preventing bridge formation with cake-like materials! Introducing a case where four Brody Disk Minis were installed.

Here is a case where we received an inquiry about "the cake accumulating in the filter suddenly falling and bridging. Is it possible to break the cake?" After testing through lending and confirming its effectiveness, it has been implemented. Our company can provide guidance for problem-solving tailored to the individual conditions of our users. Please feel free to consult us. 【Case Overview】 ■Issues - Cake accumulated in the filter falls → Bridges in the hopper - Hopper diameter: Ø200 - Discharge diameter: 2S ■Proposal - Install a total of 4 Brody Disk Minis, 2 at varying heights 【Key Points of This Equipment】 ■The elastic disk (silicone) is very important in terms of strength and durability due to the risk of foreign matter contamination. The silicone disk of this equipment is exceptionally strong and durable. Once you use it, you will understand! ■Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF materials or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0637 In the hopper of carbon flakes + carbon fine powder.

Solving user challenges in one go! Introducing examples of improving carbon fluidity.

We would like to introduce a case where a "broad disk" was installed to improve the fluidity of carbon. Bridging occurred at the hopper discharge section, and each time, workers had to hammer it, but the effect was low. Although the raw material was eventually discharged after taking time, it was very inefficient, and we received inquiries regarding this issue. With the introduction of our product, the user's problem was solved in one go. 【Case Overview】 ■ Issues - Bridging occurred at the hopper discharge section - Workers had to hammer it each time, but the effect was low ■ Results - The introduction of our product solved the user's problem in one go 【Key Points of Our Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, considering the risk of foreign material contamination. Our silicone disk is exceptionally strong and durable. Once you use it, you will understand! ■ Control (how to aerate?) is important! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0641 Promoting outflow from the feed tank

Measures against rat holes! Introducing a case where a Brody disk was installed in a feed tank.

We would like to introduce a case where "Brodisk" was installed as a measure against rat holes in a feed tank. We received a request from a customer to borrow this product, and it was tested with the most difficult-to-handle contents, resulting in favorable outcomes that led to its adoption. Our company always offers equipment for loan. We will send it promptly, so please feel free to try it out. 【Overview of Conditions】 ■ Hopper Dimensions: 1500×1500 ■ Discharge Section: 300×300 ■ Contents: Various types available, including brown rice (ground) and paddy rice (ground) 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability due to the risk of foreign matter contamination. The silicone disk of this equipment is exceptionally strong and durable. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *Details of the case can be viewed through the related link. *For more information, please refer to the PDF materials or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

At the hopper where the crushing sword mountain is installed.

Introducing a case where all four Brody disks (mini) were simultaneously turned ON/OFF! The bridge issue has been resolved.

We would like to introduce a case where we resolved a bridging issue that occurred in a feed hopper with a substance resembling flour. Due to the "gentle slope of the hopper" and "small discharge diameter," bridging occurred under the knife edge. After receiving a consultation from the user, we listened to the details and proposed a solution that was implemented. [Case Overview (Partial)] ■ Hopper Overview - Size: 500×500 - Discharge Diameter: Φ50 - Slope: Approximately 45° [Key Points of This Equipment] ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign material contamination. The silicone disk of this equipment is exceptionally strong and durable. We believe you will understand this once you use it! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more detailed information about the case, please refer to the related links. *For more details, please check the PDF materials or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0660 At the foundry sand regeneration facility

Most cases, such as bridges and rat holes, can be easily resolved with this equipment!

We would like to introduce a case where "Blow Disks" were installed in a hopper (dust collector) that generates fine dust during the regeneration of foundry sand. The issue was that the fine dust easily absorbed moisture, causing bridging when stored in the dust collector hopper, making it impossible to discharge. We provided information on the arrangement and control of this equipment tailored to the customer's usage conditions, and after detailed discussions, it was implemented. The results have been excellent, with no bridging occurring at all. 【Overview of Arrangement and Control】 - A total of 8 Blow Disks (standard type BD-15) were installed, with 4 in the lower section and 4 in the upper section. The lower section was arranged in the left, right, and center, while the upper section had the 4 disks positioned towards the corners. - The 8 Blow Disks were sequentially aerated in pairs with a time delay using a controller (C-SV4) that incorporates 4 solenoid valves. *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0663 At the hopper of the air transport machine

We can provide guidance on model selection, placement, and control according to the user's requirements!

We would like to introduce a case study where our "Brodisk" was adopted. The fluidity of the material was quite poor, and although there was an aeration mechanism, bridging occurred at the top. As a countermeasure, our product was installed. The size of the outlet at the bottom of the hopper is 2S. There is a metal multi-layer mesh section above this, and by installing the Brodisk (standard type BD-15) further up (approximately one-third from the bottom of the hopper), the customer's issue was resolved. 【Case Overview】 ■ Equipment: Hopper of an air transport system ■ Existing countermeasure: Aeration near the discharge section using multi-layer mesh ■ Hopper diameter: Ø1000 ■ Material: Spices *For more details, please refer to the PDF document or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0674 Reduce loading time for jetpack vehicles.

We would like to introduce a case you consulted about, as it is taking a long time to load.

We would like to introduce a case study where our "Brodisk" was adopted. The user consulted us, stating that loading from the dust storage silo to the jet pack vehicle was taking a long time, and they wanted to address this issue with our product (to shorten the time). This user already had multiple instances of our equipment in place, but after discussions regarding the layout and control, they decided to adopt our solution. 【Case Overview】 ■ Target Material: Collected Dust ■ Target Tank: Large Conical Storage Tank ■ Layout Overview: Approximately the lower half of the conical section 1 unit on the lower level, 2 units on the middle level, and 3 units on the upper level (total of 6 units) A total of 24 units installed 【Key Points of Our Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign material contamination. Our silicone disks are exceptionally strong and durable. Once you use them, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

In the storage tank of activated carbon + quicklime.

The durability of elastic disks is important! Here are examples of their adoption in exhaust gas treatment equipment.

We would like to introduce a case where our "Brodisk" has been adopted. This customer (plant) has experienced troubles with other air relators in the past and is currently using our product continuously. In exhaust gas treatment systems, many customers are using it in silos containing quicklime, activated carbon, and baking soda. Since these systems rarely have the silos emptied, the durability of the elastic disk in our equipment is crucial. [Case Overview] ■Silo Diameter: Ø2000 ■Discharge Port Diameter: Ø300 ■Hopper Inclination Angle: 67° ■Discharge Amount: Several 10 Kg/h ■Contents: Activated Carbon + Quicklime *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Solve the bridge of citrus powder 0682.

We would like to introduce a case where we received inquiries from end users in the food industry and successfully resolved their issues.

We would like to introduce a case study where our "Blow Disk" was installed. Due to variations in fruit types and processing conditions in the previous stages, particle size and moisture content changed, leading to the formation of bridges that could not be cleared by existing air knockers or hammering. As a countermeasure, we decided to adopt the Blow Disk. After the introduction of this equipment, bridges no longer occurred at all, and it was subsequently adopted for another large hopper. 【Case Overview】 - One standard Blow Disk installed on each inclined surface - A total of two Blow Disks are simultaneously operated with air ON/OFF *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0687 Clearing blockages in the hopper of dried hop powder.

An example adopted to address expected blockages at the hopper discharge section.

We would like to introduce a case where a plant and maintenance operator ordered "Blow Disks." In the production of hoppers for a beverage manufacturer, it was anticipated that clogging might occur at the hopper discharge section based on past experiences. Therefore, at the user's request, we were consulted about adopting "Blow Disks." After detailed discussions (regarding contents, hopper diagrams, control methods, etc.), the system was implemented. Currently, the equipment is operational at the user's site, and there have been no occurrences of bridging or powder clogs. [Case Overview] ■ Hopper Diameter: Φ900 ■ Discharge Diameter: 150A ■ Contents: Dried hop powder ■ Equipment Layout Control - Four "Blow Disks" installed near the discharge section (two at different heights) - Air aeration controlled by a controller, with each disk activated in a staggered manner *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Resolve the clogging of resin cutting powder (preliminary check conducted through lending).

We provide assistance with model selection and layout planning, as well as free loan of this equipment!

We would like to introduce a case where a user already using the "Brodisk" requested a loan of our product. The user has been using Brodisk for many years across several devices, and the model and configuration have been determined. However, they wanted to try a different method of air control, so we lent them four Brodisk units (Type 15). The four Brodisk units were manually turned on simultaneously without any issues, successfully resolving the blockage of cutting powder. As a result, they decided to implement the plan to turn on all four Brodisk units at the same time, which is a cost-effective solution. 【Usage Overview】 ■ Installation Location: Dust Collector Discharge Section ■ Dust Collector Hopper Dimensions: Approximately 1100 x Approximately 1100 ■ Hopper Discharge Section Dimensions: Ø200 ■ Target Material: Resin Cutting Powder *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Elimination of remaining carbon black emissions.

There are many varieties of materials, and we received high praise from the customer for solving everything!

We would like to introduce a case where the issue of residual discharge occurring in the weighing hopper was resolved using a "Blow Disk." A customer consulted us, stating that there was a significant amount of residue adhering in the carbon black weighing hopper, and although they attempted to address it with a knocker and a vibrator, it was unsuccessful. They inquired whether the Blow Disk could help. We lent our product to the customer, who installed it in a dummy hopper and confirmed the air injection and vibration. After reviewing the hopper design, we provided recommendations for the appropriate model and configuration. As a result of the implementation, the residual amount was reduced to about 500g. The customer praised us highly, noting that there are many types of materials, and we were able to resolve the issue for all of them. [Implementation Overview] ■ Hopper Dimensions: Ø1000 ■ Discharge Section Dimensions: 200A *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0700 Preventing bridge formation of resin grinding materials.

Achieve excellent results at low cost! Bridge prevention in the hopper of the extruder.

We would like to introduce a case where a Brodisk was implemented to prevent bridging of resin grinding materials. In certain raw materials, a mixture of virgin materials and grinding materials is used, but when the proportion of grinding materials exceeds a certain level, bridging occurs. In this case, it could not be prevented by an air knocker, and we received inquiries on how to prevent bridging. After reviewing the raw materials (mixed products) and the hopper design, we provided guidance on the recommended arrangement of Brodisk and it was implemented based on our recommendations. The results were favorable. 【Implementation Overview】 ■ Hopper dimensions: 800×800 ■ Control: All four 15-type Brodisks are turned ON/OFF with air simultaneously. *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0704 Elastic disk compatible with metal detectors Brody disk

You can also submit your exam results! If you are interested, please feel free to request a loan.

We would like to introduce a case where a "Brodie Disk" was supplied as a bridge countermeasure near the hopper discharge area. The target material is food (rice). In the event that the elastic disk of the Brodie Disk is damaged and mixes with the target material, the aim is to ensure it can be detected by metal detectors or X-ray inspection machines. Therefore, we have adopted a product that incorporates metal powder into the elastic disk. This elastic disk complies with food hygiene tests. A test report can also be provided. 【Product Specifications, etc.】 ■ Brodie Disk BD-15S-MD 2 pieces *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0711 Prevention of bridging in the gypsum board crushing hopper

A case where the customer conducted tests with a dummy hopper, and the test results were favorable, leading to its implementation.

We received an inquiry from a customer stating, "A bridge has occurred in the recycling equipment, and I would like to try a BroaDisk." Here, we introduce a case that led to the implementation. The target materials were crushed gypsum powder and gypsum board paper, which exhibited significant variability in the properties of the contents, and there were situations where hammering did not improve the condition at all. We proposed the model, layout, and control plan, and the customer conducted tests using a dummy hopper. Since the test results were favorable, they decided to proceed with the implementation. [Implementation Overview (Partial)] - Target Hopper: Hopper under the cyclone, diameter Ø1000, discharge diameter Ø200 - Layout: 4 BroaDisks × 2 tiers, totaling 8 units - Control: Aeration of 8 BroaDisks in pairs using a controller (C-SV4) with 4 built-in solenoid valves *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Mounting on the hopper of the powder roll feeder.

The results are good! There is no longer any occurrence of bridging even with very fine A powder.

This is a case study of measures taken to prevent bridging in a mixture of powder A and powder B. Powder A has an average particle diameter of about 3 μm, while powder B is coarse. There are several mixing ratios, but in many cases, bridging does not occur with the installation of partition plates in the hopper. However, when the proportion of powder A exceeds a certain level, bridging could not be resolved with partition plates or vibrators. We reviewed the powder samples and hopper diagrams, and based on our past experience, we suggested arrangements. We lent out samples, and the customer made the decision to implement them. The results were favorable, and bridging no longer occurred even with very fine powder A alone. [Case Overview] ■ Hopper Size: 800 (inclined surface) × 500 (vertical surface) ■ Arrangement: 2 breeding disks installed per inclined surface, totaling 4 disks ■ Control: 4 breeding disks controlled by controller C-SV1 *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Preventing iron powder bridges.

The Brodisk is easy to install and offers excellent cost performance! We recommended a layout plan, and it was adopted.

We received an inquiry from a user who wanted to address iron powder bridging issues, and we would like to introduce a case where we implemented BroaDisk and BroaDisk Mini. We arranged three BroaDisks along the circumference 200mm above the hopper wall from the discharge section, and three BroaDisk Minis along the circumference 75mm above the hopper wall from the discharge section, each in a staggered configuration. Using the C-SV1 controller, which has one built-in solenoid valve, we simultaneously aerated all BroaDisks and BroaDisk Minis with intermittent air ON/OFF operation. 【Hopper Overview】 ■ Hopper Diameter: Ø500 ■ Discharge Diameter: Ø80 ■ Cone Section Inclination: Approximately 60° *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other powder equipment
Mixer/agitator
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0724 Examples of deliveries compatible with metal detectors

Measures against protein powder bridging! Detectable by metal detectors and X-ray inspection machines.

We would like to introduce a case where a Bro Disk, which incorporates metal powder into an elastic disk for countermeasures against protein powder contamination, has been adopted. In the unlikely event that the elastic disk is damaged and contaminates the product, this type of Bro Disk can be detected by metal detectors or X-ray inspection machines. The Bro Disk is easy to install and economical. However, the installation position is important, so please feel free to consult us. Based on our extensive experience, we can provide guidance on the appropriate model, layout, and control for our users. 【Case Overview】 ■ Hopper Dimensions: 600×700 ■ Outlet Diameter: 150A ■ Hopper Shape: 3 inclined sides, 1 vertical side ■ Equipment Configuration: 3 units installed, 1 on each inclined surface ■ Control: 3 Bro Disks simultaneously turned ON/OFF with air using a controller C-SV1 with 1 built-in solenoid valve. *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Other sorting machines and foreign object removal equipment
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

0730 At the powdered activated carbon injection facility

A Brody disk has been installed as a measure against bridge and rat hole issues in the powdered activated carbon storage tank!

We would like to introduce a case where our "Blow Disc" was adopted in conjunction with the renovation work of an existing plant. In this silo, the discharge mechanism is a vibration discharge device, but since troubles are expected at the upper part, a Blow Disc has been installed here. By using a controller with a built-in solenoid valve, the construction of piping and wiring has become easier, contributing to the total cost. Adjustments such as air ON and OFF times can be easily made on-site, allowing for responses tailored to the situation. 【Case Overview (Partial)】 ■ Application: Bridge and rat hole measures for powdered activated carbon storage tank ■ Silo Diameter: φ2500 ■ Silo Lower Diameter: φ1200 ■ Equipment Arrangement: 8 Blow Discs × 2 tiers at the bottom of the silo ■ Blow Discs: 16 units of BD-15S-B ■ Controller: 1 unit of C-SV4 *For more details, please download the PDF or feel free to contact us.

Company：ミナギ
Price：Other

Powder Supply Device
Other powder equipment
disk

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

[Research Material] Global Market for Liquid Filter Disks

Global Market for Liquid Filter Discs: Paper, Plastic, Others, Chemical Industry, Power Plants, Irrigation, Water Treatment, Others

This research report (Global Filter Disc For Liquid Market) investigates and analyzes the current state and outlook for the global market of filter discs for liquids over the next five years. It includes information on the overview of the global liquid filter disc market, trends of major companies (sales, selling prices, market share), market size by segment, market size by major regions, and distribution channel analysis. The market segments by type for liquid filter discs include paper, plastic, and others, while the segments by application cover the chemical industry, power plants, irrigation, water treatment, and others. The regional segments are categorized into North America, the United States, Europe, Asia-Pacific, Japan, China, India, South Korea, Southeast Asia, South America, the Middle East, and Africa to calculate the market size for liquid filter discs. It also includes the market share of major companies in the liquid filter disc sector, product and business overviews, and sales performance.

Company：マーケットリサーチセンター
Price：Other

Other services
disk

View product details

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

disk Product List and Ranking from 52 Manufacturers, Suppliers and Companies | IPROS GMS

disk Manufacturer, Suppliers and Company Rankings

disk Product ranking