Last Updated： Aggregation Period:May 20, 2026～Jun 16, 2026
This ranking is based on the number of page views on our site.
Last Updated： Aggregation Period:May 20, 2026～Jun 16, 2026
This ranking is based on the number of page views on our site.
Last Updated： Aggregation Period:May 20, 2026～Jun 16, 2026
This ranking is based on the number of page views on our site.
2431～2460 item / All 3618 items
This is a Beck smoothness testing machine compliant with JIS P 8119.
The smoothness of paper and similar materials is evaluated by the rate at which air leaks through the gap between the sample pressed against a smooth glass surface and its smooth surface.
We will track and evaluate the state of absorption when one end of a strip-shaped sample is immersed in water (liquid) due to capillary action.
-
This is a testing machine for measuring the viscosity of unvulcanized rubber and the scorch time of the rubber.
● The Mooney value is automatically calibrated with a built-in weight. ● You can register test conditions and pass/fail criteria. ● Test results can be output to a PC* (optional). ● You can recall past test results (up to 100 data). ● The heater timer function allows for time savings at the start and end. ● It is equipped with overload prevention and overheat prevention devices.
This is a disperser (paint shaker, paint conditioner, shaker) used for evaluating the dispersibility of pigments used in paints and inks.
We will vibrationally blend pigments and glass beads in a glass container and compare their dispersibility.
This is a device for pressing adhesive tape against a test plate during the adhesive strength test of adhesive tape, based on JIS Z 0237.
A roller with a mass of 2 kg is moved back and forth at a speed of 10 ± 0.5 mm/sec to press the sample onto the test plate. ● Compact tabletop design that does not take up much space. ● A sample mounting fixture that minimizes air entry between the sample and the test plate is included as standard. ● Comes with a roller resting fixture for when not in use.
Film, rubber, and fabric thickness gauge
This device measures the thickness of films, rubber, woven fabrics, and other sheet-like materials, with the measurement pressure and indenter matched to their respective JIS standards according to the material.
It is a testing device for measuring the compression permanent strain of rubber materials.
Evaluate the recovery rate when a rubber material is subjected to a constant compressive strain at high temperatures and then the compressive strain is removed.
This is a device for measuring the rebound resilience of rubber in accordance with JIS K 6255.
The rebound angle of the sample will be measured, and the rebound elasticity will be calculated. The maximum, minimum, central, and average values will be processed.
This is a shopper-type sample punch for collecting test specimens made of rubber and soft plastics.
You can easily punch out using the rotational force of the handle.
It is a lever-type press cutter that collects samples using a punch cutter.
-
This is a pneumatic press machine for sample molding equipped with a degassing and cooling speed control function.
This is a press machine that incorporates operations such as degassing and cooling control to make the sample molding conditions more reliable.
This is a vulcanization testing machine (rotorless rheometer/MDR) for evaluating the vulcanization characteristics of rubber. Fully automated testing is also possible with the optional sample automatic loading and unloading device.
● The sample chamber die can be selected in addition to the flat die specification, also in a conical die specification. ● By installing the automatic sample loading and unloading device* (pin type or film type) and the data processing device*, full automation (continuous testing of 84 samples) is possible. This contributes to labor-saving and efficiency in measurement tasks. (*Optional) ● By installing options for foam pressure measurement and tan δ measurement functions, you can obtain more physical properties of rubber. *The photo includes the automatic sample loading and unloading device (optional).
This is a testing machine that applies impact to a plastic specimen and determines the impact value from the energy of the pendulum required for destruction.
● It features a digital display, eliminating errors from wear loss of the test needle and reading errors by the operator. ● By replacing the hammer and specimen support base (fixed base), it can accommodate Charpy impact tests, Izod impact tests, and tensile impact tests. ● Easy operation with a color LCD touch panel. It can display and save the average, maximum, minimum, coefficient of variation, and standard deviation of impact values. ● Measurement data can be saved to a PC. (Note: Dedicated data processing software is required as an option. PC is optional.) ● Hammer release can be operated by button. There is no individual variation during hook release, improving reproducibility. (Note: Optional.) ● Instrumentation system can be selected. (Note: Optional. For Charpy impact tests and in-basis tensile impact tests only.) ● Positioning support base can be selected. It allows easy and accurate setting of the specimen. (Note: Optional for Charpy impact tests.) ● Various safety covers (with or without top) can be selected. (Note: Optional.)
This is a testing machine for identifying the blow point of rubber materials. By understanding the minimum required vulcanization time for rubber, it contributes to improving product quality and productivity.
The blow point refers to the minimum degree of vulcanization required to eliminate the presence of bubbles generated by insufficient vulcanization within the vulcanized material at the end of the vulcanization process when vulcanizing compounds that include rubber under pressure. Measuring the blow point is very important for producing products with a short vulcanization time and no bubbles at all. This blow point varies depending on the composition of the rubber compound, the mixing method, temperature conditions, and so on, so it is necessary to measure it very frequently for quality control of vulcanized rubber products and for research and development of rubber compositions.
This is a combustion testing machine for conducting vertical combustion tests on electric wires. It consists of a draft chamber, combustion unit, and calibration kit.
● The workability has been improved by the front door that opens and closes up and down. ● The position of the smoke exhaust section and control panel can be selected depending on the installation location.
This is a DuPont-style drop impact testing machine used for drop impact destruction tests with a maximum drop height of 1000mm, utilizing a plastic sheet punch.
There is H-200 (drop height 2000mm) and H-50 for paint film (drop height 500mm) as well.
This is a DuPont-type drop impact testing machine used for drop impact destruction tests with a maximum drop height of 2000mm, utilizing a plastic sheet punch.
H-100 (drop height 1000mm) and H-50 for coating (drop height 500mm) are also available. ■ Drop height: up to 2,000mm ■ Mass of drop weight: two types of 1,000g and 2,000g ■ Radius of impact tip: 7.93mm ■ Radius of receiving platform: 8.1mm, 15.2mm ■ Dimensions: approximately W46×D30×H226cm ■ Mass: approximately 73kg *For more details, please download the PDF or contact us.
This is a tabletop universal material testing machine with a maximum load capacity of 5 kN.
■It is possible to conduct physical property evaluation tests such as tensile strength, compressive strength, and bending strength of a wide range of materials including plastics and rubber. ■You can choose from a rich lineup of chucks (gripping tools) and jigs. ■It is compact and can be installed in a space-saving manner.
This is a density meter that can automatically measure specific gravity values simply by storing test pieces made of rubber, plastic, etc., in a designated cassette (up to 64 pieces).
<Sequence of Actions> (1) Pick up the test specimen stored in the cassette using an air-operated hand. (2) Move to the testing area, place it on the weighing container, and measure the mass in the air. (3) Again pick up the test specimen, insert it into the immersion container, immerse it in the liquid for a specified time, determine the mass in the liquid, and automatically calculate the specific gravity value. (4) After testing, dispose of the test specimen in the waste box.
It is an automotive wire abrasion testing machine (scrape tester) compliant with ISO 6722.
Place the needle, subjected to a vertical load (7N or 4N), on the insulator of the test piece, and rub the surface of the insulator in both directions along the length of the test piece.
William-type rubber wear testing machine
As a rubber wear testing machine, it has been widely used for a long time, similar to the Akron method. The test specimen is pressed against a grinding plate with a constant load, and the work done is calculated from the frictional force when the grinding plate rotates, allowing for the calculation of the rubber wear volume.
You can conduct a waterproofness test for rubber and plastic coated fabrics using a simple method.
By applying water pressure from one side of the sample surface and checking for water leakage after a certain period of time, a waterproofness test can be easily conducted.
This is a portable adhesive testing machine that measures the adhesive properties (tack value) of non-sulfurized rubber, adhesive tapes, and the like. It allows for easy measurement of the adhesive strength of materials on-site.
In the molding process of tires and belts, where rubber components and reinforcing materials are adhered together in layers and vulcanized, it is very important to confirm the adhesiveness of the components in advance. This device has been developed as a tool to easily measure the adhesive strength of components on-site and can also be applied to measure the adhesive strength of tapes and similar materials. The ambient temperature at the site changes with the seasons, which also affects adhesiveness. The Tackiness Checker allows for easy measurement of adhesive strength on-site.
![Non-contact hardening evaluation device Cure Tester 'DH-1' [Testable]](https://image.mono.ipros.com/public/product/image/4ab/2000265301/IPROS43207030295884376320.jpeg?w=280&h=280)
Using digital holography, we have achieved measurement and visualization of 3D objects! It is possible to manage the drying state in seconds.
This product applies digital holography technology to non-contact and quantitative evaluation of the drying and curing processes of paints and adhesives, visualizing the drying distribution. By understanding the drying process, it enables the optimization of manufacturing lines and allows for the calculation of the necessary amount of paint and the setting of drying times based on the desired painting conditions. Furthermore, it is expected to be applicable to the evaluation of the curing process of light-curable adhesives and the drying and curing analysis of ink dots, contributing to printable electronics.
It is a testing machine (friction coefficient measuring device) that measures the static friction coefficient (μS) of materials such as plastic films, paper, and textile products using the inclined plane method.
● It has a compact space-saving design. ● It features a liquid crystal touch panel, making operations such as setting test conditions and displaying test results easy. ● Test results can be imported to a PC* (optional).
It is a specialized machine for conducting tensile and compression tests on various materials under temperature conditions. Compared to a standard universal testing machine equipped with a constant temperature chamber, it can secure a longer stroke.
● A crosshead stroke of 900mm is secured within the constant temperature chamber. ● By adopting a double-door design, temperature changes during the loading and unloading of test specimens can be minimized. (Note: If equipped with a standard line elongation gauge, only a single door will be used.) ● A 4-station (4-piece) option is also available.
This is a device that performs the mixing of pigments and vehicles under specific conditions during the paint or ink formulation stage of testing.
When converting pigments into paints or inks, a vehicle (dispersing agent) is added and ground in, but there are various methods for this process. This machine is specifically designed for testing based on JIS K 5101, where a small amount of pigment and vehicle is placed between two glass plates and rotated while applying pressure with a weight to mix them. Therefore, the setting of test conditions such as load and rotation speed can be easily adjusted according to the type of sample.
Device for evaluating the flexibility of rubber materials at low temperatures based on JIS K 6261-3 "Low Temperature Torsion Test" (Geman Torsion Tester, Cold Resistance Tester)
● The installation work of the test specimen can be performed efficiently. ● By using a pulse motor for the twisting operation, excitation locking is possible, making wire attachment easy. ● There is a lateral movement function for the test section, making maintenance of the cooling tank easy. ● Easy operation with a liquid crystal touch panel. ● After the test is completed, measurement data can be output to an Excel worksheet. (PC and Excel are optional) ● Reference standards: JIS K6261-3, ISO 1432
This is a fully automated MFR/MVR measuring device (fully automatic melt indexer, MI meter, melt flow tester) where sample input, measurement, and cleaning are completely automated.
● Fully automated from sample input to cleaning. Contributes to labor-saving, efficiency improvement, and reproducibility enhancement in measurement tasks. ● Continuous testing of 10 sample cups (optional 40 cups) is possible. ● Compact and space-saving desktop model (height 1060mm). ● A wide range of options available (automatic measurement by method A, dry air drying unit, load change mechanism, etc.).
This is a melt indexer capable of multi-weight measurement as specified by ASTM D1238 Method D, in addition to standard single weight measurement.
【Features】 ■ A load range of 0.325kg to 21.6kg is pre-installed in the device. By automatically selecting the weight, the operator's burden is reduced, and the safety of the operation is improved. ■ Up to three-step load increments and decrements (multi-weight measurement) can be performed automatically in a single test. This allows for the determination of the flow rate ratio (FRR), which is commonly used as an indicator of how the rheological properties of thermoplastic materials are affected by the molecular weight distribution. (ASTM D1238 Method D) ■ It can also be used as a standard single-weight measurement melt indexer (MFR/MVR measurement device, MFR meter, MI meter, melt flow rate testing machine).
